Installation and Operating Instructions Drillmat II
Contents
1. Press working width key Select value using the keys Press enter key Finally the value entered should be controlled once more by pressing the working width key Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 4 2 3 4 2 4 MULLER lektronik Ine GG m Impulses 100 m key With this key the number of impulses recorded to the computer by the wheel sensor during a journey of 100 m are entered There are two possibilities to enter the data 1 The impulses 100m value is known Press impulses 100m key Select value using the keys Press enter key 2 The impulses 100m value is not known Measure out and mark a distance of 100 m on the field Bring vehicle to the start position Press impulses 100m and C key simultaneously Travel a distance of 100 m Press enter key O RPM key LATIN With the initial operation the rated rom must be communicated to the computer The entry is to be carried out as follows Start up the machine Press the rom key current rom will be displayed Press enter key The value displayed at this moment in time is saved as the rated rom If monitoring is to be switched off the following entry is required Press the rom key display 0 Press enter key Rom monitoring is so switched off The rpm alarm is displayed by a hooting sound and a flashing of the arr2. board computer With wheel sensor Sensor for monitoring the sowing shaft Sensor for monitoring the fan Level sensor Row marker 1 1 Wire harness index Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 3 M m ren 1 2 Computer Delivery content Drillmat compter Battery cable Console oled Page 4 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 2 1 2 2 2 3 2 4 ER Installation instructions Drillmat Computer The computer is to be installed together with the console within the driver s field of visibility The distance from the radio eguipment or radio antenna should be at least 1 m 12V socket connection to the tractor battery For the Drillmat s current supply computer and sensors the 12V socket supplied is to be connected to the tractor battery No second device should be connected to this 12V socket The 12V socket must be protected by a 25A safety fuse which is to be found in the wire connector to the brown 12V wire Wire colours brown 12 Volt blue ground The battery s negative pole must always be at ground frame chassis Wire harness The wire harness and the sensors are factory installed Sensors Wheel sensor Hall element With the wheel sensor the device determines the distance covered as well as the area The tub
3. the field Following rhythms are supported by the Drillmat read out Rhythm left right 2 Ne Tram Ling oo gp OC Page 10 Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 ME m iien read out Rhythm left right 3 5 i 14000 beginning on the right beginning on the left beginning on the left beginning on the right beginning on the left beginning on the right beginning on the left beginning on the right beginning on the left beginning on the right beginning on the left Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 11 A KEm ren Rhythm no Tram line read Rhythm left right 18 27m 6m 7 12 ih a on the right 14 28m 8m 2 13 beginning on the left 14 28m 8m 2 13 beginning on the right 2S 2 symmetrical 000048 S 10 S 10 symmetrical 5 5 128S 12symmetrica 6 6 To adjust the tram line rhythm press the tram line rhythm key The correct rhythm is then set with the setting keys Finally the new rhythm is confirmed with the enter key If the correct tram line rhythm has been adjusted and set to 1 the side of the field where work is to begin still has to be taken into account With uneven and S rhythms work can begin on either side of the field With the even rhythms 4 8 and 12 work must begin at the side where the closed coulter is and with rhythms 6 10
4. Installation and Operating Instructions Drillmat II March 2001 DRILLMAT OO imp a Lmin JAE t a Fingabe t input Read carefully before initial operation File 30283610 02 E ME025423 03 12 2007 Contents 1 1 1 2 2 1 2 2 2 3 2 4 3 1 3 2 4 1 4 2 4 2 1 4 2 2 4 2 3 4 2 4 4 2 5 4 2 6 4 2 1 4 3 4 3 1 4 3 2 4 3 3 4 3 4 4 3 5 4 3 6 4 3 7 4 3 8 4 4 5 1 9 2 6 1 6 1 1 6 2 6 3 Page 2 SV SLeM AESGHIPUON 112535 aata a al alamaa 3 Wre MALMSSS eitea ka al tl a min 3 COMPUTE GENESIS EA AA aa 4 Installation instructions Drillmat ennaaneannnnnnnnannnnnnnnnnnnan ne 5 COMPTON AHAS AASMA taste A A ODI DVINA 5 12V socket connection to the tractor battery nrmrnenne 5 WIC NANNGSS vx sinuta mimi TRE tama m jm ak m e il 5 DEMSONS sadat aada aja jaaa ita aitia aa 5 Safely ioris aa a a iaaa 7 Specified implementation cccccssecccceececeeeeeeeeeceeseeesseeeeeeeeeeseeeeeseeeeeeas 7 oalet WASUIIC TONS e a E EERE 7 Operating instructions AAA 8 HUaroperaloN rasan a a a a aaa 8 Description of the entry Ke YS ccccseccececseeceeeceeeeceeeseueceaeesseeseeeneeesaees 8 SOENG KOVS mamma 8 PMVOLKING WIA Mmmm 8 NOC saed i lt ie menahace meena miaatanamentenaey 9 bio ae OY gee ry ek nee ene a A UE aa Ai a 9 Traminer 4074101 831680 51 AA SS SIA A SA ASAMA 10 PIKOV E a ama 12 AA SIO KOV sae taala eetikal aaa am
5. and 14 on the opposite side of the field In the case of the special rhythms no 15 29 the side of the field where work is to begin must be determined first Beginning on the left means that the side of the field when starting lies on the left hand side of the tractor in the direction of travel Consequently beginning on the right is the other way round 1 4 2 6 1 key Minni With this key the tram lines can be switched on further manually by one step at a time Stal Stop 4 2 7 Start Stop key sans With this key the automatic relaying of the tram line rhythm can be stopped and re leased again When stopped the arrow above the tram line symbol flashes Page 12 Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 4 3 4 3 1 4 3 2 4 3 3 4 3 4 MULLER lektronik Description of the function keys The device is switched on by pressing the On 1 key Switch off with the Off 0 key Should the voltage supply drop to below 9 volt e g when starting the tractor the computer switches off automatically It can be switched on again by pressing the On key Device on off Eingabe input C Start function Start The start function is released by pressing the and C keys simultaneously That means that the memory for the area time and distance is set to 0 The time is re started automatically by pressing this key This function i
6. e clip and magnet are mounted on to the wheel The red side must point to wards the sensor The sensor is to be mounted to the fixture provided at a distance of 5 10 mm A connector is provided for the sensor in the wire harness Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 5 MULL lektronik Page 6 ER Drill shaft sensor Reed contact This sensor monitors the function of the drill shaft The tube clip and magnet are mounted on to the drill shaft The red side must point towards the sensor The sensor must be mounted to the fixture provided at a dis tance of approximately 20 mm Level sensor capacitive The sensor controls the seed bin As soon as the surface is no longer covered with grain the sensor switches on and the computer sends out an alarm The sensor should be placed in the seed bin so that it switches on as soon as the set amount of residue is reached The end of the sensor should protrude 20 mm from the screw fitting The sensitivity can be regulated at the back of the sensor When the sensor switches on the lamp on the sensor lights up Row marker Reed contact The sensor indicates to the computer that the row markers have switched The sensor is to be mounted on to a static fixture opposite the switch mechanism for the row marker The magnet is to be mounted on to the switch mechanism opposite the sensor at a distance of 20 mm The mag
7. ery clamps and fuse 6 1 1 The computer dis Memory error Send in device plays HALP 00 or HALP 88 6 2 Speed is not dis Impulses 100m not entered Enter number of Im pulses 100m see 4 2 3 played The wheel sensor is not Adjust the distance of the sending any impulses to the wheel sensor to the magnet computer the ring in the to 5 10mm display is not flashing during the journey The red side of the magnet must point towards the sen Sor Connect cable in the dis tributor correctly Secure magnet with a non magnetic screw green gn signal brown br 12 volts white ws 0 volt Sensor is defective replace Computer is defective re place Wire harness is defective replace 6 3 The area is not dis Working width not entered Enter working width played see 4 2 2 Page 16 Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01
8. mu maakas aaa amaan 12 Description of the function keys n mrrennennennnenennnennennnanena 13 DEV CONO A am t 13 Ola 01 870 1070 A AAA AA NAME MUU M 13 RIME KG Vaasid E 13 SA KOY tirdid raamile mileedi 13 Kole 12575 KEY A cae atest et E tact A 14 GUE NT atred Output KOV sansaarast saata aaa jaaa 14 DISTANCE KEY at 14 EE E e EE EEr mm Ou EAEE EAEE 14 9paraton Process aana ieaiai AE aaa iaaea ii 15 Maintenance sssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mnnn 15 Saa E EE A EA 15 SENSO onanan ina jail ge es ai i lakki ua 15 EHKOETEGOVEFV co 16 The device does not switch on nniennenennenennane avane nnane naat 16 The computer displays HALP 00 or HALP 88 nniennnnennue 16 Speeds MOLAISPIAVEA ain carina aan wae aa een ae 16 Tae areg lS NOt GISDIAY 6G PMAN AAA 16 Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 ME s st 1 System description The Drillmat is used to monitor the seed drill to establish the working data and for tram line drilling The Drillmat essentially consists of The board computer control box installed in the cabin of the tractor for the entry of the reguired data as well as serving as a monitor In the case of a fault an acoustic and optical alarm is set off The machine wire harness installed on the seed drill with a connecting cable to the
9. net must momentarily be lead past the sensor when the row indicator switches It s end position should not be in front of the sensor The tram line meter moves on one position each time the row marker switches on Seed drill without track marker The switch impulse is picked up when the top link is raised The magnet and sensor should be mounted so that they approach each other in a raised position at roughly 20 mm In a working position the distance must be at least 40 mm Fan sensor Hall element Rpm monitor on the fan Both magnets are to be mounted to the fixture provided The red side must point to wards the sensor The sensor must be mounted at a distance of 5 10 mm to the sensors Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 3 1 3 2 MULLER lektronik Safety Specified implementation The Drillmat is specified exclusively for use in agriculture Any application outwith this area is regarded as unspecified The manufacturer does not accept liability for damage to persons or property result ing from unspecified use In such cases all risks are the responsibility of the user Specified implementation also includes adhering to the operation and maintenance conditions stipulated by the manufacturer in the operating instructions Relevant accident prevention regulations as well as other generally recognized safety industrial medical and road traffic rules are t
10. o be adhered to In addition the manufacturer accepts no liability in cases where arbitrary modifications have been made to the Drillmat safety instructions Before working on the electrical system or carrying out any welding operations on the tractor or on an attached implement the battery connection must be interrupted Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 7 Me m rien lektronik 4 4 1 4 2 4 2 1 4 2 2 Page 8 Operating instructions Initial operation The device carries out a self test when switched on After completion the function last used before switch off is automatically selected In the case of an electronical fault the device displays HALP 00 or HALP 88 In this case return the device for repair Description of the entry keys The keyboard has two colours White keys function keys display the recorded data Grey keys entry keys enter the machine data and control keys Se Setting keys When the or key is first pressed the display moves one poition in the required di rection Each time the key is pressed again the display moves on until the key is let loose The board computer requires following machine data in order to be able to operate at all Impulses 100m working width drill shaft rom and the tram line rhythm TE l Working width key This key is used to enter the actual working width
11. ow above the rom display every second This occurs every 5 seconds with the drill shaft alarm Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 9 MULLER lektronik 4 2 5 Tram line rhythm key Tram lines can be laid out automatically using the Drillmat For this purpose the cor responding coulters must be closed The working width of the seed drill and the cul tivator have to be taken into account The tram line rhythm can be calculated from these values Working width of the cultivator Tram line rhythm Working width of the seed drill Example You are using a field sprayer with a working width of 24 m and a seed drill with a working width of 6 m In this case the tram line rhythm is 24m 6m 4 The calculation results in even 2 4 6 etc and uneven 1 3 5 etc rhythms In the case of even rhythms the tram lines are usually laid out in 2 runs As this tends to be more inaccurate the even rhythms can be laid out in one run S rhythms e g 45 6S etc However it has to be taken into consideration that the first run is carried out with half the working width of the seed drill and subsequently begins with position 1 of the rhythm Using standard rhythms you can choose now if the left the right or all tram line coul ters should shut off That allows you to begin on the left hand boundary or the right hand boundary of
12. s to be carried out at the beginning of each operation The operating time since carrying out the start function see 4 3 2 is displayed by pressing this key If the tractor is switched off and the computer voltage free the time data entry is stopped It restarts once the device is switched on again The clock can also be stopped during operation After the time key has been pressed It can be pressed once again to stop the clock To restart it the time key has to be pressed yet again Time key ha Area key The area covered since carrying out the start function see 4 3 2 is displayed by pressing this key Measurement is interrupted as soon as the computer stops receiv ing wheel impulses Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 13 Me m rien lektronik 4 3 5 4 3 6 4 3 7 4 3 8 Page 14 Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 ha Total area key With this key the total area for a whole season can be determined The memory is set to 0 at the beginning of the season by pressing the total area and C keys si multaneously hah Current area output key With this key the current area output is displayed in ha h Km Distance key The distance covered since carrying out the start function see 4 3 2 is displayed by pre
13. ssing this key km h Speed When this key is pressed the current speed travelled is displayed 4 4 9 1 9 2 M LLER lektronik Operation process Once the machine data have been entered the following steps have to be carried out before beginning operation The row marker at the beginning of the field is to be operated so that the right side is lowered Subsequently only the start function has to be carried out see 4 3 2 After that each time the end of the field is reached and the row marker switched tram line drilling is continued automatically Even when the computer is switched off temporarily the last position is stored When the computer is switched on again the last setting is available once more Drilling can begin again immediately During the operation process the area total area operating time distance are de termined and the speed and output displayed Maintenance Computer The computer is maintenance free During the winter it should be stored at room temperature Sensors The sensors are maintenance free Copyright Muller Elektronik GmbH u Co Installation and Operating Instructions Drillmat II 03 01 Page 15 MULLER lektronik 6 Error recovery When trouble shooting keep to the intended sequence Error Cause Measures 6 1 The device does not Polarity reversal of the volt Check polarity switch on age supply Voltage supply interrupted Check battery connection cable control batt
Download Pdf Manuals
Related Search