uTV 3 User Guide
Contents
1. devices stereo sound when in to stereo output surround sound mode 27 Most probable cause Remedy Volume during streaming is not comfortable too low or too high TV audio sources have If uTV 3 is connected to the different outputvolumes optical coaxial or RCA Cinch socket of your TV adjust the volume by using the uTV 3 volume buttons If the uTV is connected to the headset output of the TV you may adjust the volume using the TV volume control Adjust volume of your satellite receiver or set top box Adjust the volume using the streamer volume buttons After connecting the uTV 3 the TV loudspeaker is switched off The headset output Choose another audio connectionoftheTVis output on your TV such as selected optical coaxial or RCA Cinch 28 Important information Please carefully read the corresponding section in the uDirect 3 or uStream user guide which is delivered along with each accessory Hazard warnings AN Keep this device out of reach of pets and children under three years AN Only use hearing aids that have been specially programmed for you by your hearing healthcare professional A Changes or modifications to any of the devices that were not explicitly approved by Unitron are not permitted Z Opening the uTV 3 might damage it If problems occur which cannot be resolved by following the remedy guidelines in the troubleshooting section of this user guide consult your hearing healthcare pr2. into the Analog Cinch input of the uTV 3 Plug the other end into Connect the 3 5 mm plug into the Analog the headset output socket of your TV input of the uTV 3 Connect the red and white plugs to the matching red and white output sockets on your TV 10 11 Cli When connecting the uTV 3 to the headset socket of your TV you are able to adjust the volume via your TV remote control CE Some TVs will switch off their loudspeakers when plugging the jack into the headset socket the TV will not be audible for other people In this case use the Cinch RCA output socket as described in Option 3 For further information on volume adjustment refer to the section on adjusting the volume The uTV 3 can also be connected to any other audio source such as an MP3 player PC or home sound system using the stereo plug cable Step 3 Charging your streamer To charge the streamer gently plug it into the charging slot of the uTV 3 as shown below Ensure the integrated plug is inserted into the streamer charging socket correctly Ensure that you are using the correct charging slot 12 Changing the charging slot for your streamer The uTV 3 comes with two charging slots You may need to change the slot using a Phillips head screwdriver 1 Unplug the USB power cable 2 Unscrew the screw on the bottom ofthe uTV 3 Lift the charging slot to remove 3 Insert the other slot into the opening Repla
3. on the uTV 3 uTV is in Bluetooth Go to the pairing section of pairing mode your streamer s user guide Only one of the blue indicator lights turned solid blue One of the devices is Make sure to switch off all connected to another other Bluetooth devices Bluetooth device except the streamer and ulV 3 Both indicator lights are solid blue but cannot hear the TV The streamer is out of Wear your streamer range of the hearing correctly Turn all devices aids off and on again The streamer is not Ask your hearing healthcare correctly programmed professional to regroup for your hearing aids your streamer and hearing aids 26 Most probable cause Remedy cannot hear the sound from the TV via the streamer Devices are not on Turn on devices Cables not plugged in Repeat steps 2 and 3 correctly No audio input to uTV 3 Make sure TV is not muted the light indicator blinks Select a 75 volume level green onthe TV Make sure the audio cable uses an out port uTV 15 mode Indicated by blue blinking status lights on both devices A short press of the streamer access 9 button will resume streaming Distance between Bring devices closer to each streamer and uTV 3 other 30 m 100 ft is the is too far maximum in line of sight To avoid streaming interruptions make sure you wear your streamer correctly and keep the uTV 3 within the operating range Some TVs may not output Try switching TV or
4. streamer 15 Daily usage OF ENE UTV 3 sc scccsscecossesscensssoscccenvascaeessesssszenceesnessess 17 Step 1 Wearing your streamer 17 Step 2 Listening to the TV sc ccosscscesssssecssessesconscrcenseeseeer 18 Step 3 Adjusting the volume of the TV signal 20 Step 4 Switching off uTV 3 and 22 Understanding the indicator lights 23 Testing the aUdiO traNSMISSION csssseecseceescesetsetseteeeeeees 24 TOUDLESHOOLING 26 IMPOFrtANtiNFOrMAtiONs scersccccsocsvssessossersecveciecsseseessesdecvecsnsseess 29 Compliance information c sscssossecsovacscenseessesesssassoesertessssseese 33 Information and explanation of symbols 35 uTV description The Unitron uTV 3 connects your hearing aids wirelessly to your TV or other audio devices through a streamer The system consists of three main elements your hearing aids a streamer and the uTV 3 hearing aid Up to 30 meters 100 ft uDirect 3 is also compatible The uTV 3 is connected to your TV or any other audio source and wirelessly sends audio signals from your TV to a streamer within a range of up to 30 meters 100 ft The uTV 3 also serves as a charging cradle for your streamer when it is not in use 5 67 8 1 Volu
5. uTV 3 first then press the 3 volume E and power 88 button simultaneously until the status light starts to blink in different colors e The streamer and the uTV 3 should connect now blue green or blue orange blinks and you should hear a sound test melody through your hearing aids The test sound continues fortwo minutes until any of the uTV 3 buttons are pressed Use the streamer volume buttons to change the volume of the test sound test sound can be heard redo the pairing procedure 24 To test the cable connections If you were able to hear the test melody from uTV 3 but you cannot hear the sound from the TV there is a problem with the cable connection e Ensure the audio cable is completely plugged in e Ensure that you connected the cable to an output and not an input different cable Try a different output socket of the TV Color codes during test mode Red no audio input on uTV Green audio input detected on uTV 3 Orange searching for a streamer Blue streaming test sound to streamer CE If no streamer is found and no audio input is available the uTV 3 will stop the test mode and its light indicator will blink green 25 Troubleshooting guide Most probable cause Remedy None of the indicator lights turned solid blue Devices are turned off Turn on devices Devices are not paired Repeat pairing see a rapidly blinking blue indicator light
6. 31 A Clean devices using damp cloth Never use household cleaning products washing powder soap etc or alcoholto clean them Neveruse a microwave or other heating devices to dry any of the devices AN The digitally coded inductive transmission technology used in these devices is extremely reliable and experiences virtually no interference from other devices It should be noted however that when operating the system near computer equipment larger electronic installation or other strong electromagnetic fields it may be necessary to be at least 60 cm 24 away from the interfering device to ensure proper operation A X ray radiation CT or MRI scans may destroy or adversely affect the correct functioning of the devices High powered electronic equipment larger electronic installations and metallic structures may impair and significantly reduce the operating range 32 Compliance information Declaration of Conformity Hereby Unitron declares that this Unitron product is in compliance with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive 1999 5 EC The full text of the Declaration of Conformity can be obtained from the manufacturer or the local Unitron representative whose address can be taken from the list on www unitron com worldwide locations Notice 1 This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada Operation is subject
7. ce the screw at the bottom and gently tighten it 13 Cli When using your streamer for the first time charge it for at least three hours even if the battery indicator turns green earlier After the initial charge you may leave the streamer in the charging slot for and unlimited time uStream uDirect 3 Charging is complete when the streamer s indicator light turns solid green The uTV 3 can either be on or off during charging Its status indicator light does not indicate the charging process The typical time to fully charge the streamer is 90 minutes We recommend that the streamer is switched off while charging A For safety reasons recharge the battery only with chargers supplied by Unitron If other chargers are used they must be USB certified 5 0 VDC 500 14 Step 4 Pairing uTV 3 with your streamer li If you have received the uTV 3 and the Unitron streamer together in a complete set they are paired already and you may move on to Step 7 If they were purchased separately they must first be paired with each other First put your streamer into pairing mode Check your streamer s user guide for further details Next put the uTV 3 into pairing mode To manually start pairing mode on the uTV 3 1 Switch uTV 3 on 2 Press the pairing button on the back and the main indicator light will start rapidly blinking blue 3 Make sure uTV 3 and the streamer are within 1m 3 ft ran
8. e P O Box 9017 Kitchener ON N2G 4X1 Canada Unitron Hearing GmbH Max Eyth Stra e 20 70736 Fellbach Oeffingen Germany For a listing of Unitron group companies please visit www unitron com Distributor 20 2665 6 0 oSo rt 3 lt 5 58 4 n C 9 0 unitron com
9. e 4 FCC IC RF Radiation Exposure Statement This equipment complies with FCC Industry Canada RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Australia Supplier Code Number N15398 New Zealand Supplier Code Number 71285 34 Information and explanation of symbols 3 The symbol is confirmation that this XXXX Unitron product meets the requirements of the amp Directive 1999 5 EC on Radio and Telecommunication Terminal Equipment The numbers after the CE symbol are the numbers of consulted certified bodies under the above mentioned directives The alert sign means that potential restrictions on its use are applicable in one or more EU Member States This device is a class 2 device and can be operated in the EU member states without restrictions for indoor use but must not operated outdoors in France This symbol indicates that it is important for the user to read and take into account the relevant information in this user guide This symbol indicates that it is important for the user to pay attention to the relevant warning notices in this user guide Important information for handling and product safety Australian EMC and Rad
10. ge 15 Ci uTV 3 will remain in pairing mode for two minutes or until the pairing has been completed Completion of pairing Wait until both indicator lights turn solid blue This can take up to two minutes but usually occurs within a few seconds Cli The uTV basestation can be paired to a maximum of four streaming devices A fifth pairing will replace the first paired device li The two devices only need to be paired once They remain paired after switching off and will automatically connect after being switched on again 16 Daily usage of the uTV 3 Step 1 Wearing your streamer Wear the streamer as shown and switch it on AR For a more detailed description of the streamers refer to the streamer s user guide After switching your streamer on it will automatically recognize your Unitron wireless hearing aids 8 In cases of interference with other hearing aids contact your hearing healthcare professional Ti The uTV 3 can only transmit the audio signal to one streamer at a time Streaming to multiple receiving streamers is not possible 17 Step 2 Listening to the TV You will hear the sound of the TV directly in your hearing aids C If you cannot hear the sound of your TV through uTV 3 repeat the setup in steps 1 6 CE If no audio is available uTV automatically stops the Bluetoogh audio transmission to the streamer after five minutes Its ma
11. in indicator light will blink green The uTV supports Bluetooth operation up to a range of 30m 100ft Line of sight between your streamer and the uTV 3 is not required However interference in the environment by walls or furniture may reduce the operating range Ifthe streamer moves out of range of the uTV 3 the wireless audio transmission will be terminated If the streamer is then moved back into range of the uTV 3 it will automatically resume streaming to your hearing aids 18 1a It may take up to ten seconds until the streaming resumes Both streaming light indicators should be solid blue during streaming i If the uTV status light e blinks green make sure the audio input to the uTV 3 is properly connected e is green make sure the streamer is switched on both ends of the neckloop are plugged in for uDirect 3 or uDirect 2 and the devices are paired e blinks blue you are in pause mode Press the streamer access button to resume streaming Step 3 Adjusting volume of the TV signal First set the volume of the TV speakers at the level to suit other viewers Next adjust the volume via the uTV 3 volume control until the sound through the hearing aids is comfortable To fine tune the overall volume of the hearing aids and uTV 3 you may use the streamer s volume 3 buttons 20 If your uTV 3 is connected to the headphone socket of your TV you may also use you
12. iocommunications compliance label This symbol shall be accompanied by the name and the address of the authorised representative in the European Community This symbol shall be accompanied by the name and the address of the manufacturer who are placing this device on the market Pes gt 35 Operating conditions This device is designed such that it functions without problems or restrictions ifused as intended unless otherwise noted in these user guides 0 to 45 Celsius and relative humidity of lt 95 non condensing Transport and storage conditions During transport or storage the temperature should not exceed the limit values of 20 60 Celsius and relative humidity of 90 for a long period of time The air pressure between 500 and 1100 hPa is appropriate The symbol with the crossed out garbage bin is to make you aware that this device may not be thrown away as normal household waste Please dispose of old or unused devices at waste disposal sites intended for electronic waste or give your device to your hearing healthcare professional for disposal Proper disposal protects the environment and health Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Unitron is under license Other trademarks and trade names are those of their respective owners 36 JE Unitron Hearing 20 Beasley Driv
13. me up button 2 Power on off button and main indicator light Volume down button 4 Pairing button 5 Power supply 6 Digital audio optical 7 Digital audio coaxial 8 Analog audio 3 5 mm 9 Audio indicator lights 10 Exchangable charging slot Getting started Step 1 Setting up the power supply To attach the country adapter 1 Insert the round corner of Click the tail of the adapter Select the adapter that corresponds to your country Included country adapters may vary by country US EU UK AUS the adapter to the round corner of the universal power supply until it is completely inserted in to lock it into place Make sure the adapter is securely locked To remove the country adapter 1 Pull back the tab on the universal power supply and hold 2 Gently pull the adapter upwards to remove it from the receptacle Connecting the power supply Place the uTV 3 next to your TV Connect the mini USB plug of the power supply to the power input Power of the uTV 3 Plug the power supply into the wall socket s Step 2 Connecting to the TV Supported audio formats The uTV 3 can be connected to any audio source such as a TV PC or hi fi system It supports three different audio input formats For best results we recommend you use the optical or coaxial connection if available on your audio device Ci Note please ensure to always connec
14. ofessional 29 A Dispose of electrical components in accordance with your local regulations A Do not use the device in explosive areas mines or industrial areas with danger of explosions oxygen rich environments or areas where flammable anesthetics are handled or where electronic equipment is prohibited A External devices may only be connected if they have been tested in accordance with corresponding standards Only use accessories approved by Unitron A Using your 3 cables any way contradictory to their intended purpose e g wearing the USB cable around the neck can cause injury A When operating machinery ensure that no parts get caught in the machine The mini USB port is to be used for the described purpose only 30 A Caution electric shock Do not insert plug alone into electrical outlets A AN For safety reasons only use chargers supplied by Unitron or stabilized chargers with a rating of SVDC min 500 mA Information on product safety AN When uTV 3 is not in use turn off the device AN Always plug in the uDirect 3 neckloop and wear it around your neck when transmitting signals to your hearing aids AN Protect the device connectors plugs charging slot and power supply from dirt and debris A Protect all devices from excessive moisture bathing or swimming areas and heat sources radiator TV top Protect devices from excessive shock and vibration
15. r TV remote control to adjust volume via the TV directly Refer to the TV user guide for more details on setting the TV volume Cli If your TV is connected to a satellite receiver or a set top box make sure the volumes of these additional devices are set to a 75 level for best audio quality results i Refer to your streamer s user guide for pairing instructions of the streamer with a mobile phone or other entertainment and communication devices such as radios or personal computers i Refer to your streamer s user guide for information on using the streamer to pause the audio transmission and other functions 21 Step 4 Switching off uTV 3 and streamer To switch off the devices To end the transmission of the TV audio signal switch off the uTV 3 by pressing the on off button as shown 22 Understanding the indicator lights Switched on On but no audio input Solid green Short blink green ooo Pairing mode Rapid blue blinking Streaming mode Solid blue Pause mode Short blink blue Test mode Mulit color blink ooo CE For a more detailed explanation of the streamer indicator lights please refer to the streamer s user guide 23 Testing the audio transmission The uTV is able to generate a test sound to check the system To start test mode e Switch on and wear your streamer correctly Switch off the
16. t uTV 3 to the audio output of your device Signal priorities Normally it is enough to connect one audio cable If more than one cable is connected and a signal is present uTV will select the best possible input in the following order optical coaxial analog 1 2 3 CE Note even though the optical and coaxial cables are only one wire the signal is stereo uTV 3 shows the selected input by an orange audio indicator light Input selected Slow blinkorange Input selected and Solid orange audio available Option 1 connecting optical cable Ifan optical output is available e Unpack the cable labeled Optical e Remove the protection caps from the plugs e Connect one end of the optical cable into the Optical input of uTV 3 and the other end into the optical output of your TV i Ou Option 2 connecting via coaxial cable If a coaxial output is available e Unpack the cable labeled Coaxial orange plugs e Connect one end of the coaxial cable into the Coaxial input of uTV 3 and the other end into the coaxial also known as digital out or S P DIF output of your TV Option 3 connecting via RCA Cinch cable Option 4 connecting to the headset socket If an RCA output red white is available e Unpack the cable labeled Analog 3 5 mm e Unpack the cable labeled Analog RCA Connect the stereo plug
17. to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Notice 2 Changes or modifications made to this device not expressly approved by Unitron may void the FCC authorization to operate this device Notice 3 This device has been tested and found to comply with the limits for a Class digital device pursuant to Part 15 of the FCC Rules and ICES 003 of Industry Canada These limits are designed to provide reasonable protection against harmful interference in a residential installation This 33 device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Notic
18. ulV3 guide unitron Hearing matters Thank you Thank you for choosing the Unitron 3 At Unitron we care deeply about people with hearing loss We work closely with hearing healthcare professionals to make advanced purpose driven solutions available to everyone Because hearing matters The intended use of the uTV 3 is to connect your hearing aids to a TV or other audio source It sends audio signals wirelessly to the hearing aids through a streamer within a distance of 30 m 100 ft It also serves as a charging station for the uDirect 3 and uStream Your uTV Hearing healthcare professional Telephone Serial number of uTV 3 Warranty Date of purchase Your streamer uStream uDirect 3 Package contents The complete Unitron uTV 3 consists of the following elements uTV 3 plus the following cables e Power supply with mini USB plug and country adapter Optical Coaxial e Analog RCA Cinch e Analog 3 5mm Table of contents UTV sscsiscssescencessncsectenssesseodssccsecssarsetscseetsesuesssossatses 2 Getting Started 4 Step 1 Setting up the 4 Step 2 Connecting to 6 Step 3 Charging your streamer 212 Step 4 Pairing uTV 3 with your
Download Pdf Manuals
Related Search