Installation and operating instructions
Contents
1. 12 2014 OPERTIS 27 OPERTIS Germany OPERTIS GmbH Prof Bier Stra e 1 5 34454 Bad Arolsen Telephone 49 5691 87741 200 Telefax 49 5691 87741 310 support opertis de www opertis de Ce MB314 02EN V001 12 20142. Antenna is defective Replace antenna Transponder obtains Transponder is not Program the no access programmed or does transponder not have the necessary authorisations Controller has wrong Reset the date and date or wrong time time Antenna is If several antennas are Wait for the temporarily not functioning no signalling connected communication is in progress at another antenna authorisation of a transponder or programming process communication process at the other antenna to finish 18 OPERTIS 12 2014 eLOCK eXpress Installation and operating instructions EN Antenna in the Siedle housing Problem Possible cause Solution Antenna is not detected by the controller Termination resistances set incorrectly Set the termination resistances correctly Each transponder is authorised for the lock Wall scanner is not programmed construction site mode Program the wall scanner see eLOCK eXpress Quick Start Guide Failure of the controller and the antennas Too many antennas at the bus Secure power supply for several antennas from somewhere else No optical or acoustic signalling at the terminal Signalling has been switched off in the eLOCK eXpress software Switch on signalling in the software 12 2014 OPERTIS 19 EN eLOCK eXpress Antenna in the Siedle housing Installation and operatin
3. However the following residual risks cannot be excluded O If the mains voltage fails there is a risk of being locked in or out In this case itis only possible to open the door using mechanical tools In this case contact OPERTIS support O If the electronics or the connection cable to the controller fail there is a risk of being locked in or out It is then only possible to open the door using mechanical tools In this case contact OPERTIS support O If an antenna is used for access control to a fuse box there is a risk of being locked in or out if a fuse is defective It is then only possible to open the door using mechanical tools 8 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing 4 Safety Instructions A The following safety instructions must be noted and followed before use OPERTIS does not accept any liability whatsoever for personal injuries or damage to property caused by failure to follow these instructions CAUTION Risk of being locked in or out Without a functioning antenna in conjunction with a door locking mechanism the door cannot be opened if the latch engages in the strike plate When installing the antenna keep the door open or ensure that the door can be opened at any time without use of the wall scanner CAUTION Risk of malfunctions Malfunctions can occur if the antenna is installed in the immediate vicinity of alternating electroma
4. OPERTIS 11 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions Pin assignment The following connections must be connected for the connection of the antenna with the controller Connection Connection Antenna connection description Controller VCC Bus 1 1 RS485_B Bus 2 2 RS485_A Bus 3 3 GND Bus 4 4 Connecting Additional Antennas A maximum of 4 antennas can be connected to one controller The data connection is made via RS485 bus wiring maximum allowable total length is 300 m e the connection cables are connected from the controller to the first antenna and from there to the second antenna etc Star type cabling is not possible Connection diagram Controller Antenne 1 Antenne 4 S VCC 4 CN QD 1 de KU a RS485 B p gt 2 2 ala 2 3 RS485 A AN fas N 3 3 3 LAN GND IAN E re 4 A A Terminating resistance For a secure RS485 bus data connection a terminating resistance must be set at both ends of the bus cable This is activated in the factory for all antennas in the ON position ON OFF switch see Figure Front of antenna The switches at all other antennas within the bus connection must be set to OFF Controller Antenna 1 Antenna 2 Antenna 4 u OFF ON 12 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Anten
5. Explanation of the symbols and signal words used AN WARNING Indicates hazards which could result in severe or fatal injuries CAUTION Indicates hazards which could result in minor or moderate injuries Indicates hazards which could result in damage to CAUTION property Indicates information and tips for optimum use of the mole instructions and the product Target group Faultless safe function of the antennas depends to a large extent on proper installation These instructions are therefore directed at competent personnel who have completed suitable training or have experience appropriate for installation maintenance care disposal and maintenance of antennas or comparable products OPERTIS Support If you have any questions which are not answered by the information provided in these instructions please contact OPERTIS GmbH Prof Bier Stra e 1 5 D 34454 Bad Arolsen Tel 49 5691 87741 200 Fax 49 5691 87741 281 Email support opertis de 4 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing Up to date information All details of the product images dimensions and versions are correct at the time of delivery of the product We reserve the right to make changes in line with technical progress and the resulting continuous improvement process of our products The current version of these instructions and further information is also ava
6. controller or a power pack Antennas A maximum of 4 antennas can be connected to one controller Connection cable single wire 0 14 0 5mm Stripped length max 9mm at the controller max 5mm at the antenna Length of the connection cable of antennas lt 300m connected in series Pin assignment Specific data Operating temperature see Section 6 Installation 20 C to 55 C Storage temperature 40 C to 85 C Humidity for operation and storage max 95 non condensing Degree of protection to EN 60529 IP54 in the Siedle frame OPERTIS 23 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions 12 Disposal Product E Disposal in accordance with WEEE Directive 2012 19 EC O Do not dispose of product in the local household waste O Send product back to OPERTIS or dispose of it at a communal collection point for hazardous electronic wastes Product packaging The product packaging must be disposed of through the local household or paper waste collection facility Notes 24 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing 12 2014 OPERTIS 25 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions 26 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing
7. red flashing and short high tone Example Activated door closes 14 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing 7 Operation and Control Programming Terminals and Transponders Terminals and transponders are programmed using the eLOCK eXpress management software Optical and acoustic signals Note The signalling of the terminals depends on the settings in the eLOCK eXpress software Optical signalling is switched on by default A buzzer can be switched on optionally for the acoustic signalling All optical and acoustic signals are given in the eLOCK eXpress system documentation In case of certain system states and events the wall scanner emits acoustic and or optical signals Optical signal Meaning 2x short blue blue 1x short green Programming with the ToDo card completed successfully 2x short blue blue 2x short red red Programming with the ToDo card not completed successfully 2x short blue blue 1x short red No programming job with the ToDo card exists for the terminal repeated short blue Programming in progress with the NFC stick 2x short green blue Use of the security card 2x short green green Switching on of fitting by an authorised transponder 2x short red red No switching on of fitting transponder is not authorised 2x short red green Switching on of fitting in constr
8. 7741 0 Fax 49 5691 87741 310 Fi info opertis de PEO f if Pre a q y F CL A a Tm A d f kr A Bad Arolsen 2014 05 12 Andreas Steinkamp f Or Datum Gesch ftsf hrer CEO Place amp date of issue Mame und Unterschrift Name and signature 12 2014 OPERTIS 21 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions Dimensions All dimensions given in mm 21 100 10 LL 38 o o o o e e c 19 30 Rating plate ES314 2001 gt Antenna Siedle housing OPERTIS Serial number 12345 12345 HW AA PEDEF SE Prof Bier Stra amp e 1 5 MAC 00 11 22 33 44 55 D 34454 Bad Arolsen Supply voltage 6 12V DC max 100mA gt C E Bitte Installabonsanleitung beachten i Please note installation instructions A Made in Germany Note on the Operating System The antenna is operated with the FreeRTOS operating system Further information under www freertos org 22 OPERTIS 12 2014 eLOCK eXpress Installation and operating instructions EN Antenna in the Siedle housing Technical data Installation environment Design Siedle colour scheme white silver metallic titanium metallic graphite brown metallic Installation environment Siedle Vario Compact intercoms Installation distance between antennas Power supply connections Power supply at least 100 mm in 3D space The antenna is supplied with voltage power via a
9. OPERTIS Installation and operating instructions Antenna in the Siedle housing ES314 2001 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions Contents 1 o AA A nn 4 About these instructions Heeres ueis ntiesieren 4 Explanation of the symbols and signal words used ocococccccccococononononononononononicininininos 4 MAES A E 4 OPERTIS SHDDOLPL anstehen c vei OP Rd EX 4 Up to date information cis oso exten eaae nde ttn cox orav AA Ch cente dor on ex ea du 5 2 Product Description 5 A ehe 5 Operating practicado 5 A 6 Detailed INTO NANO RA AAA ARA 6 3 Intended US miii ei 6 E USS EAE ate cansences vous AE E E EE E UIS pdpr cot Copiar RUD 6 Condition of the DEOGOLICE ana seen 7 Ambient CondlHlOliS ler rcd t oie i e P en eer eiie a 7 AP O po fein tete at een edie 8 A Safety Insirucli ns 2 2 kreis 9 5 SCOPE OF SUPDPIY ARAFRRNERERERERERPRERENERERFRENERFRERERERFEFRENERERERFRERERERETTRPRFRERERFRERFEERFEFEPNEREDERRRERFRERENERe 10 6 Installation O RR E IE A IN CA RE 10 e jl A RI REITER IRRE 10 Installation Tools REQUISITO courrier Cena Cir n x nh PR eng tette cep aden ede 10 COANSCHON ALTAS Controlla cosciente rl in utin y en a noua ORNA S n ERR 11 Connecting Additional Antennas essent 12 F netonah testers e TNT 13 7 Operation and Control 15 Programming Terminals and Transponders essssssesee eene 15 Optical and acoustic SIgrals
10. Spezifikationen EN 60950 1 2006 A11 2009 A1 2010 Other means of proving conformity with the essential A12 2011 requirements standards specifications used 20 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing Schutzanforderungen in Bezug auf die elektromagn Vertr glichkeit S 3 1 2 Artikel 3 1 b Protection requirements concerning electromagnetic compatibility 8 3 1 2 Article 3 1 b angewendete harmonisierte Normen Harmonised standards applied Einhaltung der grundlegenden Anforderungen auf andere Art und Weise ETSI EN 301 489 3 v 1 4 1 hierzu verwendete Standards Spezifikationen Other means of proving conformity with the essential requirements standards specifications used Ma nahmen zur effizienten Nutzung des Funkfrequenzspektrums Measures for the efficient use of the radio frequency spectrum Luftschnittstelle bei Funkanlagen gem 8 3 2 Artikel 3 2 Air interface of the radio systems pursuant to S 3 2 Article 3 2 angewendete harmonisorte Normen Einatung der grundlegenden Anforderungen auf andere Art und Weise hierzu verwendete ETSI EN 301 330 1 v 1 7 1 gt LOL Standards Schnittstellenbeschreibungen ETSI EN 301 330 2 v 1 5 1 Other means of proving conformity with the essential requirements standards interface specifications used Phone fax e mail Tel 49 5691 8
11. e Siedle housing 9 Dismantling Note Dismantle in the reverse order Therefore refer to the figures in Section 6 Installation Proceed as follows Step Activity Figure 1 Switch off power supply 2 To remove the antenna the unlocking mechanism between two Siedle modules must be actuated using the Siedle Vario key order separately not included The antenna can then be removed from the housing Disconnect the connection cables from the connection terminals of the antenna To do this press the lever of the terminal connector with a small screwdriver and pull out the cables 12 2014 OPERTIS 17 EN Antenna in the Siedle housing eLOCK eXpress Installation and operating instructions 10 Problems and Solutions Problem Possible cause Solution Antenna has no ready signal Power supply is defective or not connected Ensure power supply Connection cable to the antenna is defective or not connected Ensure connection to the antenna Operating voltage not within the allowable range Connect correct power supply voltage Controller is defective Replace the controller Antenna is defective Replace antenna Relay has already picked up Wait for the relay to drop out Transponder is not recognised no positive or negative acknowledgement Transponder is defective Replace transponder
12. e of Degree of protection to EN 60529 a Siedle Vario or Compact series P54 door intercom system UP controller Compact wall Suitable for use indoors or in the scanner in conjunction with protected outdoor area cover cap 80x80 Spacer frame high optional UP controller Compact wall Suitable for use outdoors scanner in conjunction with Surface mounted on wall housing IP65 UP controller Compact wall Suitable for use indoors or in the scanner in conjunction with protected outdoor area cover cap 55x55 Compact wall scanner If using the individual antenna and UP controller components refer to the information above Condition of the product Antennas may only be used if they are in faultless technical condition Independent modifications and changes to the product are not allowed Ambient conditions O Use in particularly harsh environments with conditions such as aggressive gases or extreme temperatures is not allowed O Note In general avoid laying the cables in the immediate vicinity of noise sources Always use a shielded cable in ambient conditions with EMC disturbance If you have any questions please contact OPERTIS Support 12 2014 OPERTIS 7 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions Residual Risk If used as intended and in compliance with the maintenance instructions this product will help to maintain your property security
13. g instructions 11 Product Specification Declaration of Conformity Konformit tserkl rung gem dem Gesetz ber Funkanlagen und Telekommunikationsendeinrichtungen FTEG und der Richtlinie 1999 5 EG R amp TTE Declaration of Conformity in accordance with the Radio and Telecommunications Terminal Equipment Act FTEG and Directive 1999 5 EC R amp TTE Directive abad OPERTIS GmbH e manufacturer Anschrift Prof Bier Stra e 1 5 Address 34454 Bad Arolsen Deutschland Germany erkl rt dass das Produkt Wandleser System declares that the product ES314 1000T ES314 1000U ES314 2000 ES314 2001 ES314 0001U Type Funkanlage Type Radio equipment Verwendungszweck Identifikation RFID 13 56MHz Intended purpose x lass 1 Ger teklasse Glass Equipment class bei bestimmungsgem er Verwendung den grundlegenden Anforderungen des 3 und den brigen einschlagigen Bestimmungen des FTEG Artikel 3 der R amp TTE entspricht complies with the essential requirements of S3 and the other relevant provisions of the FTEG Article 3 of the R amp TTE Directive when used for its intended purpose Gesundheit und Sicherheit gem 8 3 1 1 Artikel 3 1 a 4 Health and safety requirements pursuantto 83 Article 3 1 a angewendete harmonisierte Normen Harmonised standards applied Einhaltung der grundlegenden Anforderungen auf andere Art und Weise hierzu verwendete EN 50364 201 N Standards
14. gnetic fields e g transformers MRI scanners etc and transmission equipment Before installing check whether any of the above mentioned interference factors could affect the function of the wall scanner CAUTION Risk of personal injuries The antenna is fitted with an LED which has a very bright light If the antenna is supplied with voltage without a cover cap in front of the antenna the LED can dazzle Do not look directly into the light of the LED CAUTION Risk of damage to property Electronic components can be irreparably damaged if touched Note and follow the regulations and instructions in the EN 61340 5 1 standard Do not carry out any installation or maintenance work unless the power supply is switched off Note and follow the VDE guidelines VDE 0100 12 2014 OPERTIS 9 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions 5 Scope of supply The scope of supply includes the following parts Part Name ES314 2001 Antenna in the Siedle housing Device screw 4 no 6 Installation Overview The installation is divided into the following activities O Connection at the controller O Functional test AN CAUTION Risk of malfunctions If more than three antennas are operated via one controller which is operated with PoE the max allowable power output of the controller can be exceeded This can cause failure of the controller An additiona
15. ilable on our internet site www opertis de Dated 12 2014 2 Product Description Overview The following antenna is described in these instructions Art No Name Drawing ES314 2001 Antenna in the Siedle housing EN Sy e Operating principle The OPERTIS eLOCK eXpress locking system ensures continuous consistent fitout of a building Special terminal devices are available for different door types The antenna consists only of a reading unit A connected controller is required for operation of the antenna The power supply is provided via the controller or a suitable power pack The antenna is used solely for data transmission and signalling All security relevant functions such as evaluation of the communication with the transponder or control of the relay are carried out by a controller The data between the antenna and controller is transmitted in encrypted form This ensures the greatest possible protection against manipulation The management and programming of the terminals including the issue of access authorisations is carried out using the eLOCK eXpress management software 12 2014 OPERTIS 5 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions Various types of passive transponders without their own power supply such as key fobs cards or customer specific types are available in the eLOCK locking system for authorisation at the terminals These must be held at
16. l power supply 6 12V DC must be used Installation Tools Required You will need the following tools for the installation O Suitable screwdriver for installing screws available on site O Cable strippers or side cutters for stripping off the insulation and shortening the connection cable 10 OPERTIS 12 2014 eLOCK eXpress Installation and operating instructions EN Antenna in the Siedle housing CAUTION Unauthorised access following installation In the as delivered condition the antenna is in construction site mode Access is possible with any OPERTIS transponder even if not programmed Immediately following installation you should program the authorisations to prevent unauthorised access refer to the eLOCK eXpress Quick Start Guide Have the date and time reset if necessary by your eLOCK eXpress trade partner Connection at the controller Proceed as follows Step Activity Figure 1 Connect all necessary Connection terminal at the connection cables to the rear of the antenna antenna and the controller see Pin Assignment table Set the terminating resistance Rear of the antenna see section Connecting 9 9 further antennas 1 1 Then fix the cover onto the bottom section using the device screws provided i i 2 Insert the antenna in the Siedle housing order separately not included so that the LEDs are in the top right hand side 12 2014
17. na in the Siedle housing Figure front of antenna O 1 Signalling LEDs 2 Terminating resistance ON position is labelled Functional test A CAUTION Risk of being locked in or out Peripheral devices cannot be controlled without functional controllers and without a functional antenna During the functional test of the wall scanner it is necessary to ensure that the systems controlled by the controller do not obstruct anyone at the passage entrance Note If a controller is controlled by several antennas the functional test must be performed separately for each antenna 12 2014 OPERTIS 13 EN Antenna in the Siedle housing eLOCK eXpress Installation and operating instructions Proceed as follows Step Activity Result 1 Switch on power supply O Initialisation processes The controller sets up communication with the connected antennas duration max 15 seconds Signalling to the antenna fast red flashing 1 short green flash O Standby mode Wall scanner in standby state Signalling to the antenna slow red flashing relay has not picked up 2 Hold any OPERTIS transponder in front O Controller s relays pick up signalling to the antenna 2 short red green flashes and a short high tone Example Activated door opens O After the connection time has expired Relay of the controller drops out again Signalling to the antenna Short
18. scan arbre to Pr da deni e dg da at pa a Aia 15 8 Maintenance Cleaning and Care eeeeeeeeeeeeeeeeee eene eene nnns 16 ini pc rc 16 Cleaning and Cala acorde dpa nn re oda mta dn harder dta 16 Maintenance T 16 9 Dismantling m 17 10 Problems and Solutions A 18 11 Product Specification uta ddr 20 Declaralon Of COMORMILY cose deity Cer REA EAS ARA AAA 20 DIMENSIONS RC AAA een 22 RatingplatE ii AA A AA ee 22 Note on the Operating VS 22 2 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing Technical data AEAEE O ALTE PEDEHRORENCEIEIEORURELELAUESEENENERESESTUELDEUECHERFE HUND 23 se ern en 24 PA coup e e OU MS HDI IDEM ee 24 PFOGUGT ACK AGING sete toe eo Nee Ded set pared 24 KT ST A MP 24 12 2014 OPERTIS 3 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions 1 Introduction About these instructions These instructions contain important information and instructions for installation operation of the wall scanner antenna in the Siedle housing O Read through the instructions carefully before starting the installation work and putting into service O Keep the instructions in a safe place and pass them on to each subsequent user of the antenna
19. the antenna for authorisation checking Signalling The signalling of the terminals depends on the settings in the eLOCK eXpress software Optical signalling is switched on by default A buzzer can be switched on optionally for the acoustic signalling The additional power consumption for the buzzer reduces the number of locking cycles that can be achieved by battery operated terminals Detailed Information Further information on the product is given in Section 11 Product specification 3 Intended Use Area of use The antennas are only used together with OPERTIS controllers The antennas are suitable for installation in the Siedle door intercoms Vario and Compact series Combinations of the wall scanner products Note The protected outdoor area is an area which is free from splashed water in all directions Product Area of use TS controller UP controller Suitable for use in the protected indoor area Antenna in conjunction with Suitable for use indoors or in the cover cap 80x80 protected outdoor area Spacer frame low optional Antenna in conjunction with Suitable for use outdoors cover cap 80x80 Spacer frame IP65 Antenna in conjunction with Suitable for use indoors or in the cover cap 55x55 protected outdoor area 6 OPERTIS 12 2014 eLOCK eXpress EN Installation and operating instructions Antenna in the Siedle housing Product Area of use Siedle antenna in built in fram
20. uction site mode continuous short red Wall scanner is ready for use standby 2x short red red 4x long yellow System error contact sales partner continuous short yellow The fire service transponder has been used OPERTIS 15 EN eLOCK eXpress Antenna in the Siedle housing Installation and operating instructions 8 Maintenance Cleaning and Care Intervals Maintenance and cleaning may only be carried out by qualified personnel We do not provide any warranty whatsoever for damage caused by improper handling Activity Interval Maintenance 1 year Cleaning and Care Care and cleaning are not necessary for the antenna Maintenance A CAUTION Risk of being locked in or out Without a properly functioning fitting the door cannot be opened when the latch drops into the strike plate Carry out functional checks while the door is open The following functional tests are to be performed once a year if necessary by the eLOCK eXpress trade partner Step Activity Result 1 Hold an authorised OPERTIS The connected peripheral transponder in front of the device opens for the duration connected antenna s of the Of the defined opening time controller The antenna signals as described above see Optical and acoustic signals section 2 Reset the date and time 16 OPERTIS 12 2014 eLOCK eXpress Installation and operating instructions EN Antenna in th
Download Pdf Manuals
Related Search