Installation and Operating Instructions Drillmat
Contents
1. is switched on again the last setting is available once more Drilling can begin again immediately During the operation process the area total area operating time distance are de termined and the speed and output displayed Maintenance Computer The computer is maintenance free During the winter it should be stored at room temperature Sensors The sensors are maintenance free Page 14 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 6 Error recovery When trouble shooting keep to the intended sequence Error Cause Measures 6 1 The device does not Polarity reversal of the volt Check polarity switch on 299 supny Voltage supply interrupted Check battery connection cable control battery clamps and fuse 6 1 1 The computer dis Memory error Send in device plays HALP 00 or HALP 88 6 2 Speed is not dis Impulses 100m not entered Enter number of Im pulses 100m see 4 2 3 played The wheel sensor is not Adjust the distance of the sending any impulses to the wheel sensor to the magnet computer the ring in the to 5 10mm display is not flashing during the journey The red side of the magnet must point towards the sen sor Connect cable in the dis tributor correctly Secure magnet with a non magnetic screw green gn signal brown br 12 volts white ws 0 volt Sensor is defective replace Computer is defective re plac2. key the automatic relaying of the tram line rhythm can be stopped and re leased again When stopped the arrow above the tram line symbol flashes Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 11 4 3 4 3 1 4 3 2 4 3 3 4 3 4 Description of the function keys The device is switched on by pressing the On I key Switch off with the Off 0 key Should the voltage supply drop to below 9 volt e g when starting the tractor the computer switches off automatically It can be switched on again by pressing the On key Device on off Eingabe Input C Start function Start The start function is released by pressing the and C keys simultaneously That means that the memory for the area time and distance is set to 0 The time is re started automatically by pressing this key This function is to be carried out at the beginning of each operation The operating time since carrying out the start function see 4 3 2 is displayed by pressing this key If the tractor is switched off and the computer voltage free the time data entry is stopped It restarts once the device is switched on again The clock can also be stopped during operation After the time key has been pressed it can be pressed once again to stop the clock To restart it the time key has to be pressed yet again Time key ha Area key The area covered since carrying out the star
3. with position 1 of the rhythm Following rhythms are supported by the Drillmat No Rhythm No Rhythm __ No rhythm o Js 2 Tram line Tram line ginning on the right ginning on the left ginning on the left 9 10 18m 4m 27 6m beginning on the right Page 10 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 4 2 6 4 2 7 To adjust the tram line rhythm press the tram line rhythm key The correct rhythm is then set with the setting keys Finally the new rhythm is confirmed with the enter key If the correct tram line rhythm has been adjusted and set to 1 the side of the field where work is to begin still has to be taken into account With uneven and S rhythms work can begin on either side of the field With the even rhythms 4 8 and 12 work must begin at the side where the closed share is and with rhythms 6 10 and 14 on the opposite side of the field In the case of the special rhythms no 15 16 18 19 the side of the field where work is to begin must be determined first Beginning on the left means that the side of the field when starting lies on the left hand side of the tractor in the direction of travel Consequently beginning on the left is the other way round H 4 1 key iil With this key the tram lines can be switched on further manually by one step at a time tart Stop Start Stop key hmm With this
4. Installation and Operating Instructions Drillmat February 1999 DRILLMAT Io AN imp d t min s Li Input EN p Read carefully before initial operation File 302836 02_E ME019441 03 12 2007 Contents 1 SYSTEM GESCHIPUION mes 3 talh Machine GIST ID UNO este 3 k2 COMPUTE garment ear meee emcee eae eT SL ME A SES ene mn nem eee ere 4 2 Installation instructions Drillmat 5 2x MEC 0 sst E 5 2 2 12V plug connection to the tractor battery rrnm 5 2 3 Signal distributor machine o eie eee ree okkad koda nahka vatti takt 5 D MER uL tec 5 3 S G 7 31 Specified implementation AASA rennene 7 SA ATELY MSU CHONG eana e aod E E NS 7 4 Operating InsiructiOns eio eoe cene cedo aka eaae eco eda Nana ee nina pa Ran 8 Alk Malope FAO e adden A E UUTE AD 8 4 2 Description of the entry keyS ccccccceecesesseeeeeeeeeeeeseseeeeeeeeeeaeaseeeeeeseaaaeees 8 A ZA SAMAAKOVS RET TD LET 8 4 2 2 Working Width KOV so isvasat ast vatti matata a kama Aaa 8 429 Ampulses 100m KOV aa taani data aina alakaalulist 9 dod ERIN KOV isanime taala aaa evn laa saani 9 425 Tatil yt Koy sersan da noo idea elec i e limiidis 10 ak A A A ai TRE 11 4 2 7 Start stop KOV osak armas makaak avakatse lk alea a 11 4 3 Description of the function keys
5. butor installed on the frame of the Drillmat with a connecting ca ble to the board computer With wheel sensor Sensor for monitoring the drill shaft Sensor for monitoring the fan Level sensor Track marker 1 1 Machine distributor S A Tram line L 0 MAA x Hall element mm IM d Tram line R Hall sensor mit a n Cable 14x1 00qmm U U Fan Lg 6 50m Level Drill shaft Track marker 19 30pin multipoint plug m S V GS RET WT Reed contact wn Mil r Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 3 1 2 Computer Delivery content Drillmat compter Battery cable Console Jelle OO Dime Page 4 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 2 1 2 2 2 3 2 4 Installation instructions Drillmat Computer The computer is to be installed together with the console within the driver s field of visibility The distance from the radio equipment or radio antenna should be at least 1 m 12V socket connection to the tractor battery For the Drillmat s current supply computer and sensors the 12V socket supplied is to be connected to the tractor battery No second device should be connected to this 12V socket The 12V socket must be protected by a 25A safety fuse which is to be found in th
6. d at this moment in time is saved as the rated rpm If monitoring is to be switched off the following entry is required Press the rpm key display O Press enter 2 key Rpm monitoring is so switched off The rpm alarm is displayed by a hooting sound and a flashing of the arrow above the rpm display every second This occurs every 5 seconds with the drill shaft alarm Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 9 4 2 5 Tram line rhythm key Tram lines can be laid out automatically using the Drillmat For this purpose the cor responding shares must be closed The working width of the seed drill and the culti vator have to be taken into account The tram line rhythm can be calculated from these values Working width of the cultivator Tram line rhythm cM Working width of the seed drill Example You are using a field sprayer with a working width of 24 m and a seed drill with a working width of 6 m In this case the tram line rhythm is 24m 6m 4 The calculation results in even 2 4 6 etc and uneven 1 3 5 etc rhythms In the case of even rhythms the tram lines are usually laid out in 2 runs As this tends to be more inaccurate the even rhythms can be laid out in one run S rhythms e g 4S 6S etc However it has to be taken into consideration that the first run is carried out with half the working width of the seed drill and subsequently begins
7. d use In such cases all risks are the responsibility of the user Specified implementation also includes adhering to the operation and maintenance conditions stipulated by the manufacturer in the operating instructions Relevant accident prevention regulations as well as other generally recognized safety industrial medical and road traffic rules are to be adhered to In addition the manufacturer accepts no liability in cases where arbitrary modifications have been made to the Drillmat Safety instructions Before working on the electrical system or carrying out any welding operations on the tractor or on an attached implement the battery connection must be interrupted Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 7 4 1 4 2 4 2 1 4 2 2 Page 8 Operating instructions Initial operation The device carries out a self test when switched on After completion the function last used before switch off is automatically selected In the case of an electronical fault the device displays HALP 00 or HALP 88 In this case return the device for repair Description of the entry keys The keyboard has two colours White keys function keys display the recorded data Grey keys entry keys enter the machine data and control keys E Setting keys When the or key is first pressed the display moves one poition in the required di rection Each time
8. e Distributor is defective re place 6 3 The area is not dis Working width not entered Enter working width played see 4 2 2 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 15
9. e wire connector to the brown 12V wire Wire colours brown 12 Volt blue ground The battery s negative pole must always be at ground frame chassis Signal distributor machine The signal distributor and the sensors are factory installed Sensors Wheel sensor Hall element With the wheel sensor the device determines the distance covered as well as the area The tube clip and magnet are mounted on to the wheel The red side must point to wards the sensor The sensor is to be mounted to the fixture provided at a distance of 5 10 mm A terminal block is provided for each lead in the machine distributor Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 5 Page 6 Drill shaft sensor Reed contact This sensor monitors the function of the drill shaft The tube clip and magnet are mounted on to the drill shaft The red side must point towards the sensor The sensor must be mounted to the fixture provided at a dis tance of approximately 20 mm Level sensor capacitive The sensor controls the seed bin As soon as the surface is no longer covered with grain the sensor switches on and the computer sends out an alarm The sensor should be placed in the seed bin so that it switches on as soon as the set amount of residue is reached The end of the sensor should protrude 20 mm from the screw fitting The sensitivity can be regulated at the back of the senso
10. mrnnnnrn 12 ASA DEVICE ONON ee a A A netile 12 4 32 Ola scis E ula titel aves mands Jul j medad 12 Soo ME UU os RETE t 12 4 94 TASA c m 12 49 09 Ola mal ea KOy amaan klaadi kala aa aa alata amaan 13 4 3 6 Current area DUDU KOY oerni ana a BR E eiue 13 4 37 DISTANCE KOV ronn te cet a a lo Soe OAN N 13 4 30 5h20d CM EUER 13 44 Operation DIOCOSS ereraa kski exe o Tau vester t eiu 14 5 Malle pepe 14 or ME 88111 910151 e E 14 5 2 SOTISOLSM coi shear etes ue Evo ce beue souci WEE bs WE SERE caussa eeu s Rev ode ae 14 6 ENOr 6 2762474 51 0 NE PD DEOS 15 6 1 The device does not switch on nvsrrrrnnnnnnnnnenenenennnannenananna 15 6 1 1 The computer displays HALP 00 or HALP 88 sseesssessss 15 6 2 The speed is not displayed 3 1usruimssde saak yu E uo Dena kaka kese aama avati esa YR REFER ES 15 6 3 The areais not displayed ce duet eer rouen a eb Eo tene de en 15 Page 2 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 1 System description The Drillmat is used to monitor the seed drill to establish the working data and for tram line drilling The Drillmat essentially consists of The board computer installed in the cabin of the tractor for the entry of the required data as well as serving as a monitor In the case of a fault an acoustic and optical alarm is set off The machine distri
11. r When the sensor switches on the lamp on the sensor lights up Track marker Reed contact The sensor indicates to the computer that the track markers have switched The sensor is to be mounted on to a static fixture opposite the switch mechanism for the track marker The magnet is to be mounted on to the switch mechanism opposite the sensor at a distance of 20 mm The magnet must momentarily be lead past the sensor when the track indicator switches It s end position should not be in front of the sensor The tram line meter moves on one position each time the track marker switches on Seed drill without track marker The switch impulse is picked up when the top link is raised The magnet and sensor should be mounted so that they approach each other in a raised position at roughly 20 mm In a working position the distance must be at least 40 mm Fan sensor Hall element Rpm monitor on the fan Both magnets are to be mounted to the fixture provided The red side must point to wards the sensor The sensor must be mounted at a distance of 5 10 mm to the sen sors Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 3 1 3 2 Safety Specified implementation The Drillmat is specified exclusively for use in agriculture Any application outwith this area is regarded as unspecified The manufacturer does not accept liability for damage to persons or property result ing from unspecifie
12. t function see 4 3 2 is displayed by pressing this key Measurement is interrupted as soon as the computer stops receiv ing wheel impulses Page 12 Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 ha 4 3 5 Total area key With this key the total area for a whole season can be determined The memory is set to 0 at the beginning of the season by pressing the total area and C keys si multaneously hah 4 3 6 Current area output key With this key the current area output is displayed in ha h km 4 3 7 Distance key The distance covered since carrying out the start function see 4 3 2 is displayed by pressing this key km h 4 3 8 Speed When this key is pressed the current speed travelled is displayed Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions Drillmat 02 99 Page 13 4 4 5 1 5 2 Operation process Once the machine data have been entered the following steps have to be carried out before beginning operation The track marker at the beginning of the field is to be operated so that the right side is lowered Subsequently only the start function has to be carried out see 4 3 2 After that each time the end of the field is reached and the track marker switched tram line drilling is continued automatically Even when the computer is switched off temporarily the last position is stored When the computer
13. the key is pressed again the display moves on until the key is let loose The board computer requires following machine data in order to be able to operate at all Impulses 100m working width drill shaft rom and the tram line rhythm M pel Working width key This key is used to enter the actual working width Press working width key Select value using the keys Press enter 2 key Finally the value entered should be controlled once more by pressing the working width key Copyright M ller Elektronik GmbH u Co Installation and Operating Instructions 02 99 4 2 3 4 2 4 imp 100 m Impulses 100 m key With this key the number of impulses recorded to the computer by the wheel sensor during a journey of 100 m are entered There are two possibilities to enter the data 1 The impulses 100m value is known Press impulses 100m key Select value using the keys Press enter 2 key 2 The impulses 100m value is not known Measure out and mark a distance of 100 m on the field Bring vehicle to the start position Press impulses 100m and C key simultaneously Travel a distance of 100 m Press enter 2 key ON RPM key 57725 With the initial operation the rated rpm must be communicated to the computer The entry is to be carried out as follows Start up the machine Press the rpm key current rpm will be displayed Press enter 2 key The value displaye
Download Pdf Manuals
Related Search