EN DE Original-Montage- und Betriebsanleitung Original assembly
Contents
1. Antriebstechnik Tubular motor GEIGER SOLIDline Motor control GEIGER SoftZeroWireless GU45 F02 for cassette awnings E Original assembly and operating instructions EN Index 1 General information ccceeeceseeeseceeeeeeeeeeeeeeeeeseeeeeeeeeeeeeees 2 2 Guarantee irpan cocentexeed devareseudeshvees aAa AEAN SANKE SaN i 2 33 INtENGED Use ra a aaa ara A a aaa rae Aaaa aat Eai 3 A Safety INSTHUICH ONS i sisesetira ieessseaaennaianvennentevediacanivnignesindactinniise 3 5 Safety instructions for assembly ccccccceeeeeeseeeeeeeeeeeeeenees 4 6 Installation instructions cceecee cece eens teen eeeeeeeeeeeeeeeeeeeeeees 5 7 Information for the specialist electrician 2 0 0 6 8 Bringing into service scpincisiisiesnessncdinesasenedenertanertansdewesaanace 6 9 Learning deleting the radio code cceccceeeeeeeeeeeeeeeeeeeeeeees 7 10 Adjusting the End Position ccccccccssssseeeeeeeeeeeeneeeeeeneeeeeees 7 11 Teaching in the Incline Position eeseeeeeeeeeeeeeeeeeeeeeeeeeeeees 9 12 Deactivation of the close range function eeeseeeeeeeeeeees 9 13 GEIGER Powertronic 2 cccceeeceeeceeeeeeeceeeeeeeeeeeeeeeneeeneeeees 9 14 Function description of radio MOtor cccceeeeeeeeeeeeeees 10 15 R dio COUOS 2 esices tes ceicccsccsedececeetet dewecasdeecevescevees iveetdeneseievevisce2. Product Venetian blind motor motor for rolling shutter motor for awnings Type designation GJ56 GR45 GU45 The designated product is in conformity with the European Directive 2006 42 EC Directive 2006 42 EC of the European Parliament and of the Council of 17 May 2006 for the approximation of laws regulations and administrative provisions of the Member States concerning machinery 2004 108 EC Directive 2004 108 EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89 336 EEC The conformity of the designated product with the provisions of the directives is proved in particular by full compliance with the following standards DIN EN 60335 1 DIN EN 55014 1 EN301 489 03 DIN EN 60335 2 97 DIN EN 55014 2 EN300 220 3 DIN EN 62233 DIN EN 61000 3 2 DIN EN 61000 3 3 The accredited VDE Testing and Certification Institute EU Identification No 0366 Merianstr 28 D 63069 Offenbach tests and certifies for the company Gerhard Geiger GmbH amp Co KG Authorised representative for technical data Gerhard Geiger GmbH amp Co KG Address Schleifmihle 6 D 74321 Bietigheim Bissingen of p jw Chil GREG Bietigheim Bissingen 15 02 2013 Hans Michael Dangel General Manager 14 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 21 Technical data Technical
3. one another unintentional codes can be transmitted to other radio receivers Recommendation When starting the motor for the first time disconnect motors that are intended to be operated EN by another pair of keys or by another code from the mains www geiger de EN 11 EN 15 16 17 Initiating End Positions No incline position has been programmed in To initiate the end positions a short press of the button in the corresponding direction of movement is enough To stop the movement a short press of the button in the opposite direction is enough Should a sun wind sensor be integrated into the system in automatic mode solar on the end positions are initiated An incline position is programmed in To initiate the end positions the button corresponding to the correct direction of movement must be pressed for at least 1 5 seconds A short press of the button less than 1 5 seconds will cause the incline position to initiate To stop the movement a short press of the button in the opposite direction is enough Should a sun wind sensor be integrated into the system in automatic mode solar on the end positions will always be initiated Obstacle detection When after the teaching of the first complete uninterrupted travel from one end position to the other end position is carried out the torque needed is learnt In any following complete uninterrupted travel from end position to end position the torque nee
4. Click Please note The correct button allocation for up and down happens automatcally after programming of the end position is complete www geiger de EN 7 EN Adjusting the Lower End Position The lower end position must be adjusted first From far range press the up or down button and hold until the awning has reached the desired end position Corrections are possible with the up and down buttons Saving the lower end position From close range press the up or down button and hold approx 1 second then release The motor responds 1 x Click Click Adjusting the Upper End Position From far range press the up or down button and hold approx 3 seconds until the awning retracts and locks As soon as the casing is closed the motor automatically turns off and the upper end position is saved You will hear the motor 1 x Click Click The up and down buttons are now assigned to the corresponding turning direction of the motors Programming is finished and the motor has changed to normal operation AN Finally conduct at least one trial run so that the motor electronics can automa tically detect the threshold of the torque disconnection A Please note When changing the end position the power level is reset to its standard setting Level 0 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 11 Teaching in the Incline Position To move from a
5. data of tubular motor SOLIDline KS GU45 GU4506 GU4510 GU4520 GU4530 GU4540 GU4550 Voltage 230 V 50 Hz Current 0 36A 0 47 A 0 63 A 0 8 A 1 0A 1 0A Cos Phi coso gt 0 95 Inrush current factor x 1 2 Power 83 W 105 W 140 W 180 W 220 W 220 W Torque 6Nm 10 Nm 20 Nm 30 Nm 40 Nm 50 Nm Speed 16 rpm 16 rpm 16 rpm 16 rpm 16 rpm 12 rpm Protection class IP 44 Total length 506 5 516 5 546 5 566 5 586 5 586 5 mm mm mm mm mm mm Operating mode S24min S24min S25min S24min S24min S24min Sound pressure level 39 dB A 39dB A 41dB A 41dB A 43 dB A Diameter 45 mm Weight approx approx approx approx approx approx 1 85 kg 1 90 kg 2 20 kg 2 40 kg 2 70 kg 2 70 kg Ambient temperature humidity Operation T 10 C 60 C H max 90 Storage T 15 C 70 C dry and non condensing place 1 SOLIDline ZN 1 mm SOLIDline COM SIC 3 5 mm SOLIDline SOC 3 mm 2 The average sound pressure level data are intended for guidance only The values were determined by GEIGER at a distance of 1 m with a hanging motor at idle speed and averaged over 10 seconds There is no reference to any specific test standard Subject to technical modifications 22 Notes on waste disposal Recycling of packaging materials In the interest of environmental protection please contact your local government s recycling or solid waste management department to learn more about the services it provides Waste di
6. out in the vicinity During operation observe the danger zone Do not use the installation if people or objects are in the danger zone Urgently shut down damaged installations until repair Unconditionally shut down the unit during maintenance and cleaning operations Pinching and shearing points are to be avoided and must be secured This appliance can be used by children aged 8 and above and persons whose physical sensorial or mental capacities are impaired or who have no experience or EN know how if they have been supervised or been given instructions on the use of the appliance and if they understand the possible resulting dangers Children are not permitted to play with the device Cleaning and maintenance should not be carried out by children gt The rated sound pressure level is less than 70 dB A gt Disconnect the device from the mains power supply for maintenance and replace ment of parts If the motor is disconnected via a plug connection the operator must be able to control from any place to which it has access that the plug is removed If this is not possible due to design or installation the disconnection from the power supply must be ensured via locking in the disconnected position e g isolator gt The motor tube can get very hot during prolonged use When working on the unit do not touch the tube before it has cooled down v vvvvvyv www geiger de EN 3 EN 5 Safety instructions for assembly ATTEN
7. transmitter Radio codes 10 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 Amaximum of three different functional codes can be taught The motor can thus be a member in three groups that are independent of one another Additionally a further two radio sensor codes can be taught If three radio codes have already been taught and it is attempted to teach a fourth code the radio code learnt as the third code is cancelled and replaced by the new code If two radio sensor codes have already been taught and it is attempted to teach a third code the radio sensor code learnt as the second code is cancelled and replaced by the new code Example Wireless receiver in the motor Group 1 Group 2 Group 3 Sensor 1 Sensor 2 Code Code Code Code Code 00 0 00 4 t o o ioo o M sh in mn For your documentation record any hand held remote sensor codes taught into the motor here Group 1 Group 2 Group 3 Sensor 1 Sensor 2 Programming in the far range near range In the radio receiver of the motor is integrated an approach detector that recognizes whether a radio transmitter is operated from some distance far range at least 1 5 metres distance to the motor control or 0 5 metres to the motor cable or it is operated close to the antenna near range at most 15 cm removed or directly on the motor connecting cable Caution If radio receivers or motor connecting cables lie near to
8. TION Important safety instructions Follow all installation instructions as incorrect installation can lead to serious injuries When mounting the motor without any mechanical protection of the driven parts and of the tube which may become hot the motor must be installed at a height of at least 2 5 m above the ground or of another level which provides access to the drive Before the motor is installed all cables which are not needed are to be removed and all equipment which is not needed for power operated actuation is to be put out of operation The actuating element of a manual release must be mounted at a height of less than 1 8 m If the motor is controlled by a switch or pushbutton the switch or pushbutton must be mounted within eyeshot of the motor The switch or pushbutton must not be located in the vicinity of moving parts The height of installation must be at least 1 5 m above the floor Permanently installed control devices must be attached visibly In case of devices extending horizontally a horizontal distance of at least 0 4 m must be respected between the fully extended part and any other fixed element The rated speed and the rated torque of the motor must be compatible with the device The mounting accessories that are used must be designed in accordance with the selected rated torque Good technical knowledge and good mechanical skills are necessary for the motor installation Incorrect installation can lead to serious i
9. a reduction in the closing power causes a looser closing and less strain to the fabric Closing power levels from level 0 to level 7 GEIGER delivery setting level 0 A Caution By manually raising the closing power e g from level 0 to EN level 7 the fabric endures more strain In which situations is the GEIGER Powertronic applied e Ifthe casing does not completely close e Ifthe closing operation should be optimised for better fabric protection When can the GEIGER Powertronic be applied e Anytime this function can be activated during initial operation as well as at a later date Which resources are necessary e GEIGER hand held remote which is taught in in accordance with Chapter 9 Please note The end positions are not affected when the GEIGER Powertronic is activated e When the end position teach in mode is activated the power level is reset to e level 0 GEIGER delivery setting Only activate the GEIGER Powertronic after the end positions have been taught in and a complete trial has been conducted www geiger de EN 9 Activating the GEIGER Powertronic 1 At close range press the Up or Down button and hold approx 3 seconds until you hear the motor 1 x Click Click 2 From far range press the Up or Down button and hold approx 1 second until you hear the motor 1 x Click Click 3 At close range press the Up or Down button and hold approx 3 seconds until you h
10. an Instead of in the upwards direction motor runs downwards End positions are set wrongly First set the upper then the lower end position Hand held transmitter does not work Check the battery The wind sensor has triggered Try it again after the expiry of the wind cut off time Inadvertent deletion of the radio code Start learning radio code again see chapter 9 After running several times The motor became too hot and has the motor breaks down and switched off no longer responds Try it again after a cooling time of about 15 min The motor no longer runs automatically The sun automatic control mechanism was switched off The wind sensor has triggered Try it again after the expiry of the wind cut off time Inadvertent deletion of the radio code Start learning radio code again see chapter 9 The motor does not react to the near range Move as close as possible to the motor head with the hand held transmitter Exchange the batteries in the hand held transmitter The close range is deactivated To activate the close range disconnect the motor from the electrical supply for about 3 seconds EN 19 Maintenance The drive is maintenance free www geiger de EN 13 EN 20 Declaration of conformity a GEIGER EC Declaration of Conformity Antriebstechnik Gerhard Geiger GmbH amp Co KG Antriebstechnik Schleifm hle 6 D 74321 Bietigheim Bissingen
11. ded is automatically reset Slow changes in the installation due to ageing soiling cold or heat are thus automatically taken into consideration If a travel movement in UP direction is blocked by an obstacle the motor switches off and a small return motion takes place The running direction in which the obstacle was recognized is blocked The block is removed if the motor has been operated in the opposite direction for a certain time An obstacle must thus first be released before the motor can be operated again in the direction of the obstacle End position correction If a lengthening shortening of the hanging has resulted due to e g temperature changes this will be automatically corrected by closing the awning If due to temperature changes an adjusted sleeve performance is set and the hanging runs against the stop unit the end position is immediately corrected After the first trial the motor automatically identifies the torque necessary to close the awning and closes it with the lowest possible power so that the fabric is optimally protected 12 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 18 What to do if Problem Solution No short click click on switching on the motor Motor not plugged in Please check the plug connection Check connecting cable for possible damage Check the mains voltage and allow the cause of the voltage breakdown to be tested by a specialist electrici
12. ear the motor 1 x Click Click 4 Now the power can be incrementally increased with the Up button and incrementally reduced with the Down button 5 When the desired power level is reached at close range press the Up or Down button and hold approx 1 se cond The motor is now in its normal operating mode 1 x Click Click As soon as the lowest or highest power level has been reached and you try to continue to raise or lower the level you will hear a signal from the motor 2 x Click Click Should there be no activity for 60 seconds input mode will be deactivated The power level set will be assumed 14 Function description of radio motor EN In the delivery state each GEIGER radio receiver and radio transmitter is equipped with the GEIGER Code so that the motor can be operated immediately in order for example to facilitate the installation of hangings on the winding shaft For security reasons the GEIGER Code must be overwritten by an individual code This takes place automatically in the teaching for the first time of an individual code see chapter 9 learn delete radio codes 0 0 2 3 4 5 6 7 8 2 3 4 5 6 7 8 GEIGER code individual code example The DIP switches No 8 and No 9 have no function Please take the description and adjustments from the operating instructions of the appropriate hand held wall
13. es 11 16 Initiating End Positions 000 eccce cece eeeeeeeeeeeeeeeeeeeeeeeeeseeneees 12 17 Obstacle detections svcd sccsesteeestccesiecsscercesstersdecepsivecessnexs 12 18 End position Correction cccccceeceseeeeeeeeeceeeeeeeeeeeeeeeeees 12 19 What COO Ti cise dite eccerewweven tances dca sdecwaucanwavunvdveoudbcownwcs 13 20 MaintenanGe iiss ivecs coves ciccvedeceni veces seveseuevenseuveavenes anana daidan aana 13 21 Declaration of conformity cceeeeeeeeeeeeeeeeeeeeeeeeeneeeeeeeeeeees 14 22 Technical Gata isisisi cdvcscecs cescevesseeesdevvvssdvevesevedevcvavvsenseesys 15 23 Notes on waste disposal ccccccececeeceeeeeeeeeeeeeeeeeeeeneeeneeees 15 1 General information Dear customer By purchasing a GEIGER motor you have decided on a quality product from GEIGER Thank you very much for your decision and the confidence placed in us Before you put this drive into operation please observe the following safety instructions It serves for the prevention of danger and for the avoidance of personal injury and damage to property The installation and operating instructions contain important information for the installer the specialist electrician and the user Please pass on these instructions if you transfer the product These instructions should be kept by the user Guarantee In the case of incorrect installation contrary to the installation and operating instructions and or constructional modif
14. f the drive and marked on the tube Installation into awnings Insert motor with a suitable adapter and drive into the shaft G up to the stop of the shaft adapter Fix the motor support on the awning Fix the motor together with the shaft on the motor support The bearer locks into place Depending on the selected motor head different fixation systems can be used Place the motor with square insert in the star shaped bearer and lock with pin Place the motor into the existing engine bearer and lock Place the motor in a compatible engine bearer with clip system and lock with spring or rotating lever The GEIGER SOLIDline motor is suitable for shaft diameters from 50 mm XI EN www geiger de EN 5 EN 7 Information for the specialist electrician Caution Important installation instructions Mains 230V 50Hz Please follow all installation instructions since incorrect installation can lead to N the destruction of the motor and the PE switching unit The operations with the service clamps must only be carried out by a skilled electrician f The parallel operation of several SOLIDline SoftZeroWi reless motors is possible In this case the maximum load be of the switching unit must not be exceeded PVC cables are not suitable for equipment used outdoors or exposed to prolonged high levels of UV radiation These cables should not be used if they are likely to
15. ication the legal and contractual guarantee for property damage and product liability lapses EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 3 Intended use The motors of the model range SOLIDline GU45 F02 with the SoftZeroWireless control are designed exclusively for the operation of cassette awnings The motors may not be used for the operation of roller grilles garage doors furniture and lifting tools GU 45 xx x Motor control Torque in Nm Motor diameter GEIGER universal drive 4 Safety instructions ATTENTION Important safety instructions For personal safety it is important to follow these instructions Please keep these instructions for future reference gt Do not allow children to play with stationary controls Keep remote controls away from children gt The installation is to be checked regularly for defective balance signs of wear or damaged cables and springs if relevant gt Do observe the moving sun protection system and keep persons away until it has closed completely gt When operating the manual release with the sun protection system open please be cautious as it can fall down quickly if springs or tapes wear off or are broken gt Do not operate the device if operations such as for example window cleaning are to be carried out in the vicinity Disconnect the automatic controlled device from the mains power supply if opera tions such as for example window cleaning are being carried
16. n arbitrary position to the desired end position press and hold the two way button for approx 3 sec until you hear the motor 1 x Click Click Then release the button The incline position is now saved Changing the Incline Position See Teaching in the Incline Position However this is for a newly desired position Deleting the Incline Position Stop the awning from moving up and down and press and hold the button approx 5 sec until you hear the motor 3 x Click Click 12 Deactivation of the close range function If two motors are installed so that both trigger in the close range there is the option of deacti vating the close range function in one of the two motors The prerequisite is that the motors must be assigned to different button pairs To deactivate the close range function move the desired hanging to the upper end position push the UP button and keep it pushed for about 5 seconds until the motor confirms 2 x click click The motor must be disconnected from the mains briefly to active the close range function 13 GEIGER Powertronic The GEIGER Powertronic enables the user to change the motor s closing characteristics The user can raise or reduce the closing power applied through the motor This way he or she influences the closing characteristics of the casing A rise in the closing power causes a tighter closing of the casing with increased stress on the fabric
17. njury Electrical work must be carried out by a qualified electrician in accordance with the regulations in force locally Only use connecting cables that are suitable with the environmental conditions and which meet the construction requirements see accessories catalogue If the device is not equipped with a connecting cable and a plug or other means for disconnecting from the mains with a contact opening on each pole according to the conditions of the overvoltage category Ill for full disconnection a disconnecting device of this type must be incorporated into the permanently installed electrical installation according to the wiring rules Do not mount the connecting cables near hot surfaces A plug for the disconnection of the motor from the power supply must be accessible after installation Damaged connecting cables must be replaced by GEIGER connecting cables of the same type The device must be mounted as described in the installation instructions Fixations shall not be made with adhesives since they are regarded as unreliable 4 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 6 Installation instructions Before fixing the strength of the masonry or of the subsurface is to be checked Prior to installation please check to ensure there is no visible damage to the motor like cracks or open cables Caution If the tube is screwed riveted to the drive the measure must be taken from the tube end to the center o
18. s the learning mode is deac tivated The motor returns to normal operation 3 x click click r a1 max 15 cm D or about 3 sec 9 Learning deleting the radio code The learning mode must be activated first in order to delete the radio codes In the close range press UP or DOWN key for about 1 second The motor actuates 1 x click click The remote code is taught to the motor max 15 cm e AN al or about 1 sec If no action takes place within 60 seconds the learning mode is deac tivated The motor returns to normal operation 3 x click click Deleting the radio code The learning mode must be activated first in order to delete the radio codes At close range press the UP or DOWN key and hold approx 5 seconds The motor reacts immediately 1 x Click Click Keep the key pressed about 5 sec until the motor confirms the deleting of the radio codes with 1 x Click Click Please note You can only delete all remote codes and sensor remote codes together It is not possible to delete individual remote codes 10 Adjusting the End Position It is required for the upper end position to act as a stopper for torque deactivation e g casing contour In order to adjust the end position the learning mode must first be activated Activating the end position mode From far range press the up or down button and hold until you hear the motor 1 x Click
19. sposal of electric and electronic equipment Electrical and electronic equipment must be collected and disposed of separately in accordance EN with EU regulations CEDGAS www geiger de EN 15 EN For technical questions please call our service team at 49 0 7142 938 300 They will be happy to assist you Antriebstechnik Gerhard Geiger GmbH amp Co KG Schleifmuhle 6 D 74321 Bietigheim Bissingen Telephone 49 0 7142 938 0 Telefax 49 0 7142 938 230 www geiger antriebstechnik de info geiger antriebstechnik de 16 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113
20. touch metal parts that can heat up to temperatures exceeding 70 C Connecting cables with plug connectors of the Hirschmann Electronic Company are tested and approved with couplings of the limit stop Hirschmann Company radio receiver green yellow 8 Bringing into service Definition of near range Distance of the hand held transmitter to the motor control max 15 cm or hold at the hand held transmitter directly on to the motor connecting cable The motor connecting cable thus serves up to a length of 3 metres as an antenna Definition of far range Distance of the hand held transmitter to the motor control min 1 5 metres or Distance of the hand held transmitter to the motor connec ting cable min 0 5 metres Activate learning mode Connect the motor to the power grid Switch on the mains The motor makes a short back and forth movement 1 x click click After each interruption of the voltage supply the connect to 1 x click click learning mode can be activated for 30 min mans gt The learning mode is necessary in order S a to transmit radio codes or in order to be able to adjust the end positions again 6 EN Gerhard Geiger GmbH amp Co KG 100W0536en V001 1113 In the near range press UP or DOWN key and keep it pressed for about 3 seconds until the motor actuates 1 x click click If no action takes place within 60 second
Download Pdf Manuals
Related Search