Operating instructions - OPERTIS Produktkatalog
Contents
1. OPERTIS Operating instructions Programming station ES0780 eLOCK GB Operating instructions Programming station ES0780 Contents 1 MVE OCU GUO iio nee 4 RDOUBIDESEAINSIEUC OR ee et uen de dt de 4 Explanation of the Symbols and Signal Words Used 4 PAGES 9r0UB An u en euere 4 OBER US SUBDON nee ee een 4 Up to date status of the information 5 2 PrOQUCT DeSCriDHON emet 5 DY CVG WY RE aus etaient ii idee nicotine 5 Funciona DFINCIDI eS 5 BETA CANON ALON ee NR 5 3 tended Use on nee een 6 ALTE CS U Co ee a DO E a de tn 6 GORIVOM OP me DOUCE RUE 6 AMDISNTCONOIIONS ASS m ETE 6 FAC SICA IS RES nana er Emm 6 4 Safety InSIEUCHON SH conne Gate nee ten ane tua tease 7 5 USC and Operation ae ln 7 ARE EE LE e RR UU essen 7 BGONNECHON AO WAGE PO ntm een de oder den de er one eee 7 Programming thhedqdenmlllGl Sc ou ecdesia bte et eee din desert ue 8 6 Servicing Cleaning and Maintenance uur 2u0002an00nnanuonnnnunnnnnnnnnnnunnnnnunnnnnen 9 SEVEN ernennen er 9 Gleaningzand Maintenance eaeesinsinlen 9 7 Problems and SoIUlllO S usc icio vas ous dui a Sa nannten 9 8 IPFOGUCl Specificallons ne nn 10 DECIA AIO ON COMLONIMINY T T TET 10 DR SIONS oso nu aces a E on e 10 VST GA OA S TU 11 9 DISPOSal nun aaa 11 PROC ee ee 11 PLOQUCLDACKAG HG PR ER T LE 11 07 2013 OPERTIS 3 GB eLOCK Programming station ES0780 Operating instructions 1 Introduction About these instructions These ins2. age there is a risk of an electric shock Connect one PC only via a USB cable at the USB socket N CAUTION Risk of locking in or out The programming station is absolutely necessary for programming the identifiers It should be stored in a secure place easily accessible to authorised persons so that is available when needed 5 Use and Operation Installation A PC with installed eLOCK Center software is absolutely necessary for installation of the programming station Separate installation of drivers is not necessary Plug amp Play Connection to the PC Proceed as follows Step Activity Figure 1 Connect the B connector small connector ofthe USB cable total length max 3 metres to the front of the programming station Q 2 Connect the A connector large flat connector to a free USB slot of the PC VS NN 07 2013 OPERTIS 7 GB eLOCK Programming station ES0780 Operating instructions Programming the identifiers Step Activity Figure 3 Place the identifier in or on the Card trough provided on the programming station Note Place older versions of the ES5950 key without cover on the bow with the key bow in the middle of the trough and hold fast 4 For programming procedure details see eLOCK system documentation software 8 OPERTIS 07 2013 eLOCK GB Operating instructions Programming station ES0780 6 Servicing Cleaning and Maintenance The servicing cleaning and maintena
3. nce may be carried out by qualified personnel only Warranty cover is excluded for damage caused by improper handling Servicing The programming station does not require servicing Cleaning and maintenance CAUTION Damage to property due to incorrect cleaning Incorrect cleaning can cause the surfaces to be attacked and damaged O Do not use any alkali or acidic cleaning agents or cleaning agents containing chlorine O Do not use cleaning agents with scouring additives O Do not use scouring instruments e g brushes Proceed as follows Step Activity Figure 1 Wipe surfaces with a damp cloth 7 Problems and Solutions Problem Possible cause Solution Access to identifier User does not have Have authorisation faulty authorisation to access issued by eLOCK identifier administrator Identifier is not correctly Place identifier on the placed on the programming station programming station correctly several identifiers in the Place one identifier only access area of the on the programming programming station Station Identifier is from another Use identifier from own system system Identifier is defective Replace identifier 07 2013 OPERTIS 9 GB eLOCK Programming station ES0780 Operating instructions Problem Possible cause Solution Access to identifier System configuration is Check system faulty incorrect configuration Programming station is Connect programming not or is incorrec
4. of protection IP41 according to EN 60529 Class of protection Ill safety extra low voltage according to DIN EN 61140 9 Disposal Product X Disposal in accordance with WEEE Directive 2012 19 EU O Do not dispose of product by throwing it in the local household waste O Return product to OPERTIS or dispose of at a municipal collection point for hazardous electrical wastes Product packaging Dispose of the product packaging in the local household and paper waste disposal system 07 2013 OPERTIS 11 OPERTIS CE OPERTIS GmbH Prof Bier Stra e 1 5 D 34454 Bad Arolsen Telefon 49 5691 87741 0 Telefax 49 5691 87741 310 info opertis de www opertis de M7000 70GBB V003 07 2013
5. red We reserve the right to make changes due to technical progress and the resulting continuous improvement process to which our products are subjected The current version of these instructions and further information is also available on our internet site www opertis de Dated 07 2013 2 Product Description Overview The following programming station is described in these instructions Art No Drawing Name ES0780 Programming station e USB cable included in the scope of supply 1 Contact area for identifier 2 USB connection Functional principle The programming station is used for programming identifiers in an eLOCK lock system It is connected to a PC on which the eLOCK Center software is located The data transfer takes place via the standard USB cable supplied The programming station is used for transferring or reading out the authorisations for identifiers in an eLOCK lock system directly from the eLOCK Center software to the RFID transponder in the identifier Detailed information Further information on the product is given in Section 8 Product opecifications 07 2013 OPERTIS 5 GB eLOCK Programming station ES0780 Operating instructions 3 Intended Use Area of use The programming station is required for the programming of identifiers in all OPERTIS lock systems except eLOCK AddDelete Condition of the product The programming station may only be used if it is in a technically perfect condi
6. tion Independent modifications and changes to the product are not allowed Ambient conditions The programming station is intended for use at a suitable office workstation Use outside buildings or in a particularly polluted environment e g in aggressive gases high humidity in extreme temperatures or in a very dusty environment is not allowed If you have any questions please contact OPERTIS Support Residual risk lf used properly and if the maintenance instructions are followed this product will Support your property security However the following residual risks cannot be excluded O Ifthe electronics fail no new identifiers can be created or existing identifiers cannot be changed Successors cannot be generated for lost identifiers therefore they cannot be blocked at authorised fittings O Ifthe PC fails neither identifiers nor fittings can be created or changed Successors cannot be generated for lost identifiers therefore they cannot be blocked at authorised fittings 6 OPERTIS 07 2013 eLOCK GB Operating instructions Programming station ES0780 4 Safety Instructions The following safety instructions must be read and followed before use OPERTIS does not accept any liability whatsoever for personal losses or injuries or damage to property caused by failure to note and follow these instructions N WARNING Risk of personal injuries When connecting the programming station via the USB socket to the mains volt
7. tly station to the PC witha connected to the PC USB cable Programming station is Replace programming defective Station Programming station eLOCK Center is Re install eLOCK is not recognised by __ incorrectly installed Center Een USB connection at PC is Connect programming defective station to another USB connection Programming station is Replace programming defective station Programming station System configuration is Check system is not recognised by incorrect configuration PC The USB connection Use active USB hub does not supply sufficient Current 8 Product Specifications Declaration of conformity OPERTIS GmbH herewith declares that the Programming Station fulfils the basic standards and other relevant specifications of the 1999 5 EG and 2011 65 EU directives and that they are CE compliant A copy of the statement of conformity can be ordered from the OPERTIS Support Dimensions All dimensions are given in mm 141 27 10 OPERTIS 07 2013 eLOCK GB Operating instructions Programming station ES0780 Technical data Housing Colour black Material ABS plastic Specific data Power supply 5V DC 100 mA via USB connection does not require its own power supply Connection USB cable type Mini B 5 pole OPERTIS Art No ES0792 Operating temperature 0 to 55 C Storage temperature 40 C to 70 C Air humidity for operation and max 95 non condensing storage Degree
8. tructions contain important notes and information on operation of the ES0780 programming station O Read through the instructions carefully and attentively O Keep the instructions in a safe place and pass them on to each subsequent user of the programming station Explanation of the Symbols and Signal Words Used WARNING ndicates risks which could result in fatal or severe personal injuries CAUTION Indicates risks which could result in fatal or severe personal injuries CAUTION Indicates risks which could result in damage to property Denotes information notes and tips on optimum use of Note the instructions and the product Target group These instructions are directed at competent personnel entrusted with the servicing maintenance and disposal of trouble free operation of the programming station and who has successfully completed suitable vocational training for these activities or has had the necessary appropriate experience OPERTIS Support If you have any questions extending beyond the information provided in these instructions please contact OPERTIS GmbH Prof Bier StraBe 1 5 D 34454 Bad Arolsen Tel 49 5691 87741 200 Fax 49 5691 87741 281 E Mail support opertis de 4 OPERTIS 07 2013 eLOCK GB Operating instructions Programming station ES0780 Up to date status of the information All details on the product images dimensions and models correspond to the status at the time the product is delive
Download Pdf Manuals
Related Search