Assembly and operating instructions Automatic Door Control
Contents
1. TC channel In Door 1 Rack 1 front door addition four normally closed contacts are provided Door 2 Rack 1 rear door that can be assigned individually and connected to Door 3 Rack 2 front door their manually initiating keys or other adequate Door 4 Rack 2 rear door switching elements The Automatic Door Control Unit receives an identification so it can be automatically detected and set up by the CMC TC system The Automatic Door Kit provides the magnetic locking of the rack doors that is activated by the Automatic Door Control Unit The holding magnets of the Automatic Door Kit in their active state are supplied with 24 V power When the command for opening the door is issued the Automatic Door Control Unit deactivates the magnets and the installed gas pressure dampers open the rack doors Access Input 1 2 3 4 Four connections for Access Input components A channel for the manual door opening is provided for each door Automatic Door keys or TS 8 comfort handles with door opener function are connected to open the doors manually Power Connection for the 24 V power supply Automatic Door Control Unit 3 3 2 Proper use Assembly in the 19 frame with 7320 440 The Automatic Door Control Unit may only be used for the automatic opening of the TS 8 rack doors in an emergency situation Other applications other than those mentioned in this Is manual are expressly not permitted Warning The system may not automatica2. be exceeded Connection of the Automatic Door Control Unit to the CMC TC I O unit Connect the inputs from Door 1 2 and Door 3 4 with any free port of the CMC TC I O unit as shown in Fig 5 Use the provided RJ12 cable for this purpose Door 1 2 to Port 1 Door 3 4 to Port 2 Doors VO Door 123 4 1 2 3 4 Power max 24 Access Input 12 3 4 O Bal 1320 210 Fig 5 Connection to the CMC TC I O unit Automatic Door Control Unit Connection of the Automatic Door Control Unit to a Basic CMC or an LCP Plus Control Unit Connect the inputs from Door 1 2 and Door 3 4 with any free port on the Basic CMC as shown in Fig 6 Use the RJ12 cable provided for this purpose Door 1 2 to Port 1 Door 3 4 to Port 2 silla Power I O Door 123 4 a E 1 2 3 4 Access Input 1 2 3 4 N los Ma TE MA M M B E 320 110 Fig 6 Automatic Door Control Unit with Basic CMC Connection of the Automatic Door Kits As many as three holding magnets can be connected to the Door 1 4 outputs Connect the Automatic Door Kits as shown in Fig 7 Door 1 Rack 1 front door Door 2 Rack 1 rear door Door 3 Rack 2 front door Door 4 Rack 2 rear door Doors VO Door 1 2 3 4 1 2 3 4 Power max 24 Access Input 123 4 Fig 7 Connection of the holding magnets of the Automatic Door Kits Connection of the Automatic Door key 7320 793 or alternat
3. 3 Software Updates cccooocccccconnnnccconcncnnonnnonnns 9 Storage and diSpoSal cccccccconccnnccccnnnnncnnnannnns 10 Technical specificatiOns ooccccocnncconnncconnno 11 Spare DANS esenp 12 NVINING CIA QUAM caia 195 GOSS ANY cota ike ie dete eee 14 Customer service addresses cccccceeeeeeeees Automatic Door Control Unit 1 Notes on documentation These instructions are intended for trained specialists who are familiar with the assembly installation and operation of the system Read these operating instructions prior to commissioning and be sure to keep them accessible for later use RITTAL can accept no liability for damage and operating problems resulting from non compliance with these instructions 1 1 CE labelling The Control Unit satisfies the CE conformity requirements of the EMC Directive 2004 108 EU The declaration of conformity can be requested from Rittal Service 1 2 Storing the documents These instructions and all associated documents constitute an integral part of the product They must be given to the device operator The operator shall be responsible for storage of the documents to ensure that they are readily available when needed 1 3 Used symbols and technical terms The signal word classifies the effects of a danger in case of the non observance of the safety instructions A differentiation is made between Danger A dangerous situation for which the failure to com
4. RITTAL tl 320 790 Automatic Door Control Unit FRIEDHELM LOH GROUP A4069307IT 74 Contents 1 Notes on documentatiON oooccccocccccnccnccnnnnononoos Ll CE laBelINd sisas no 1 2 Storing the docUMEenNTS ooccccccccocncnncccnonnonnos 1 3 Used symbols and technical terms 1 4 Other applicable documenkts c 2 Safety INnSthucthoOns seis aa 2 1 Generally applicable safety instructions 3 Device description cococcccccccocncccnnoconnnnaninnon 3 1 Components and function description 3 1 1 Automatic Door Control Unit 3 2 Proper Use usadas li llas 39 DIMENSION Sirio 3 4 Scope of delivery ooncccccccoocconccccnonccnncnnnnos 4 Assembly and installation coo oo 4 1 Assembly procedure cccccccecseeeeeeeeeeeees 42 Astillero 4 3 Installation procedure ccoooncccncccccnicocinnononos 4 3 1 Automatic Door Control Unit wiring 4 3 2 Installation guidelines Commissioning and configuration 6 OME ANON ee tS 6 1 Display elements c cccccseseeeseeeeeeeeeees 6 2 Error Messages ccccoccccconcnccnnnnncnnnccnanononancnnas 7 Fault and remedial action oonccconncncon mmmmmo 8 Inspection and maintenance ccoccccccccnniconinon 8 1 lt INSPCCHON cout 8 2 Maintenance ccccoccnccnncnncnnnnccnanononanonnnanenononess 8
5. after consultation with Rittal up to 50 m UL approval 10 m after consultation with Rittal up to 50 m UL approval 10 m after consultation with Rittal up to 50 m UL approval Not required because 24 V DC safety extra low voltage CU to Basic CMC CU to LCP Plus Automatic Door Control Unit 11 Spare parts Miniature fuses type 5 x 20 mm 1 5 A slow The product will be replaced in case of an Automatic Door Control Unit defect 12 Wiring diagrams A Word template for creating circuit diagrams can be downloaded from the RITTAL homepage www rittal com This template allows all products of the CMC TC system to be represented and integrated in circuit diagrams 13 Glossary CMC Computer Multi Control CMC TC Computer Multi Control Top Concept CU Control Unit Automatic Door Control Unit PU Il Processing Unit Il 14 Customer service addresses If you have technical questions or questions regarding our product range please contact the following service contact Tel 49 0 2772 505 1855 http www rittal com E mail info rittal de Schaltschrank Systeme Industrial Enclosures Coffrets et armoires lectriques Kastsystemen Apparatsk pssystem Armadi per quadri di comando Sistemas de armarios AVIAFUTJ LYIO Yr Stromverteilung Power Distribution Distribution de courant Stroomverdeling Str mf rdelning Distribuzione di corrente Distribuci n de corriente Elektronik Aufbau Syst
6. bserve front of the Automatic Door Control Unit the country specific regulations Doors 1 2 F1 1 5 A miniature fuse 20 mm slow for Automatic Door Kits 1 and 2 Doors 3 4 F1 1 5 A miniature fuse 20 mm slow for Automatic Door Kits 1 and 2 Power 1 Automatic Door Kit 1 2 switched on off Power 2 Automatic Door Kit 3 4 switched on off Doors 1 2 3 4 Automatic Door Kits are activated deactivated The doors can be closed The display is not affected by operating the Automatic Door keys or the TS 8 comfort handle 6 2 Error messages All error messages are issued from the Processing Unit or the Basic CMC 8 Automatic Door Control Unit 10 Technical specifications Designation Automatic Door Control Unit Housing type Plastic coating with metal trim 1 U 44 5 mm 136 mm 129 mm approx 0 6 kg Height Width Depth Weight without packaging Potential equalisation Earthing Protection category IP 40 according to EN 60529 I _ lt LED display 2x Power Control 4x Doors Status 4x max 24 V DC 400 mA 4x max 30 V DC 1A Door outputs Normally closed contacts Operational area Temperature 5 to 45 C 42 to 113 F Humidity 5 95 Storage temperature 20 to 60 C 4 to 140 F Rated voltage 1 x 24 V DC 2 0 ASELV Fuses 1 5 A miniature fuse slow UL approval CMC TC connection 2 x RJ 12 sockets Maximum cable length CU to I O unit 10 m
7. d configuration After the successful installation and the connection to the mains voltage the Automatic Door Control system must be configured This is done from the Processing Unit website as shown in Fig 11 Type Door Magnet Output Status On Message Text Door Opening Delay 0 s Range 0 999s Timeout stay y Trap Receiver e 1 e 2 4 M 4Log send SMS Format 1424384 send eMail Format 1428384 Combinations Switch Output Of On Accept Reset Fig 11 Automatic Door Control System website Legend Output status Current status of the door opening magnets Message text Specific text Delay Power on delay for the door opening magnets Time out Definition of the state the Automatic Door Control system should assume after switch off and on Trap receiver Activation of up to three SNMP trap messages Send SMS send e mail Activation of SMS and e mail messages in a fault situation Switch output Activation deactivation of the door opening magnets Accept Confirmation of the configuration input Reset Reset the configuration to the default values Combinations Calling the Combinations menu See Fig 12 Combinations 7 Fault and remedial action Output 4 4 Door Opening Malfunction Remedy Group 1 Check the miniature fuses in If status of no sensor selected is lok T Door Control land status of no sensor selected is OK Check the power supp
8. eme Electronic Packaging Electronique Electronic Packaging Systems Electronic Packaging Contenitori per elettronica Sistemas para la electr nica IVLYFRO ZIA MNyT PVATA System Klimatisierung System Climate Control Climatisation Systeemklimatisering Systemklimatisering Soluzioni di climatizzazione Climatizaci n de sistemas REE ATA IT Solutions IT Solutions Solutions IT IT Solutions IT l sningar Soluzioni per IT Soluciones TI TYYa yvay Communication Systems Communication Systems Armoires outdoor Outdoor behuizingen Communication Systems Soluzioni outdoor Sistemas de comunicacion 13117 3 VVATA Rittal GmbH 4 Co KG Postfach 1662 D 35726 Herborn RI T TAL Telefon 49 0 2772 505 0 Telefax 49 0 2772 505 2319 eMail info rittal de www rittal de Ft TT
9. ively the comfort handle with door opener function 7320 794 Remove the jumpers at the connection terminals Access Input 1 4 Connect the Automatic Door keys as shown in Fig 8 Doors VO Door 1 2 3 4 1 2 3 4 Power max 24 Access Input ay yy Fig 8 Connection of Automatic Door keys The keys can be placed anywhere We recommend that the keys are placed where they are easily accessible provided there is no danger of them being activated inadvertently The maximum cable lengths must not be exceeded Doors VO Door 1 2 3 4 1 2 3 4 Power max 24 Access Input 12 3 4 Fig 9 Automatic Door Control Unit with TS 8 comfort handle with door opener function 6 Automatic Door Control Unit Connection of the 24 V power supply Doors VO Door 1 2 3 4 1 2 3 4 Power max 24 Access Input 12 3 4 p aim 7320 425 Fig 10 24 V power supply A Note We recommend that the doors are monitored with access sensors 7320 530 because the Automatic Door Control Unit does not provide this unction 4 3 2 1st 2nd 3rd 4th Installation guidelines Note AN The installation guidelines described below are based on a risk analysis for the Automatic Door Control system and must always be observed in order to ensure the highest possible functional reliability not only in normal operation but also in a fault situation The Automatic Door Control system mu
10. lly activate any door systems that exhibit dangerous door forces that can injure persons in any manner Only the RITTAL Automatic Door Kit product may be activated _ 7610 000 a Da A AA y Fig 3 19 attachment Mounting module with CMC 7320 450 3 3 Dimensions W x Hx D 136 mm x 44 mm x 129 mm 3 4 Scope of delivery Automatic Door Control Unit Assembly installation and operating instructions Nylon tape fastening RJ12 connection cable 4 Assembly and installation The Automatic Door Control Unit is installed in a RITTAL TS 8 rack in accordance with the procedure described below 4 1 Assembly procedure Assembly with nylon loop fastening Fig 4 Enclosure assembly with 7320 450 Fig 2 Nylon loop fastening 4 Automatic Door Control Unit 4 2 Installation Warning The system operates only with safety extra low voltage Under no circumstances may voltages higher than those prescribed be connected to the system Lethal anger 4 3 Installation procedure Once all system components have been installed in accordance with the associated installation instructions the installation as described below is performed AM Note For the installation the system must remain disconnected from the power supply for the complete time Otherwise defects can occur to the unit 4 3 1 Automatic Door Control Unit wiring Note AN The maximum signal cable length of 6 m must not
11. ly of Group 2 the Automatic Door Control If status of no sensor selected is OK Doors cannot be closed Unit land status of no sensor selected is OK oo and If Group 1 and Group 2 then switch of Output Check the plugs at the Access Units inputs and Accept Reset the Doors outputs Check the cabling in Fig 12 Combinations website l particular the connection o Doors remain closed in the ble f the P Combinations can be used to combine the status of Open svstem status eae ONES di p y Unit or the LCP Controller to the connected sensors and group them to form dedicated status messages the Automatic Door Control Unit 8 Inspection and maintenance 6 Operation The Automatic Door Control Unit does not have any 8 1 Inspection control elements The system must be checked regularly for its complete correct functioning RITTAL recommends a 6 1 Display elements regular function test when required but not in intervals longer than one year Duoni Deore aie 8 2 Maintenance m al The system does not require any maintenance 1 2 123 4 sau Sed Kitama sont 8 3 Software updates max 1 5 A T At the time of performing the installation check that the Processing Unit the Basic CMC and the LCP Fig 13 Automatic Door Control Unit display elements controller have the latest software version Legend 9 Storage and disposal The following display elements are located on the Please dispose of as electronic scrap and o
12. ply to this note causes death or severe injury Warning A dangerous situation for which the failure to comply to this note can cause death or severe injury Caution A dangerous situation for which the failure to comply to this note can cause minor injuries Note Identification of situations that can cause material damage The signal words are shown in the following form in the instructions e g Signal word 1 Description of the danger and its effect 2 Description of the behaviour of the user to prevent danger 2 Automatic Door Control Unit 1 4 Other applicable documents In conjunction with these operating and installation instructions reference is also made to the operating and installation instructions for the CMC TC Processing Unit Il and to the operating and installation instructions for the products listed in AtdiwuM nts are contained on the CD ROM that accompanies the Processing Unit Il The appropriate current version can be downloaded as PDF file from the RITTAL homepage http www rittal com 2 Safety instructions 2 1 Generally applicable safety instructions Please observe the following general safety instructions when installing and operating the system The assembly and the installation of the system in particular the wiring of enclosures with mains power may be performed only by a trained electrician Observe the valid regulations for the electrical installation for the co
13. st be compatible to the controlling system should the power fail If the Automatic Door Control system is used in combination with an LCP system both systems must be connected to the same power supply If the fan motors of a connected 3 phase LCP system are connected to a phase the power supply of the Automatic Door Control system must be connected to the same phase as the fathenaiaiamatic Door Control system is controlled from a Processing Unit both systems must be connected to the same power supply The rack doors must always be able to be opened manually at anytime using an Automatic Door key or TS 8 comfort handle with door opener function Please always install one of the named options Rack doors must not open inadvertently If the 24 V power supply to the Automatic Door Control Unit fails the rack doors will open Use the alarm configuring of the PU II or the Basic CMC to ensure that in this case all required protective measures are initiated for the installed server systems Rack doors must not remain closed in a fault situation The connected controller must be configured so that the relevant alarms are signalled and manual intervention is possible To ensure the continuing correct functioning of the system the correct functioning of the Automatic Door Control system must be checked in its full scope once after successful installation and then in regular time intervals Automatic Door Control Unit 5 Commissioning an
14. tomatic Door Control system Power NO Door max 24 1 2 3 Access Input 1 2 3 4 Automatic Door Control Unit 7320790 7320 792 or 7320 795 Up to four Automatic Door Kits or 7320 796 Up to four Automatic Door keys 7320 793 Up to four TS 8 comfort handles 7320 794 Fig 1 Automatic Door Control Unit rear trim panel win goor opener tunnon a 230 V 24 V power pack with 7320 725 Legend connection cable 7200 210 I O Door 1 2 or 3 4 Two RJ12 sockets for connection to an I O unit frame of a CMC TC system Fastening components in the 7320 450 The input 1 2 and input 3 4 activates Doors 1 The CMC TC Processing Unit Il can be used to define the appropriate combinations that cause the doors to be opened in an alarm situation The Automatic Door Control Unit performs the automatic opening of the rack doors should the cooling system of the racks fail or the rack doors The Automatic Door Unit can be activated by a need 7 ba opened because of a smoke alarm and CMC TC I O unit in conjunction with a PU II or fire extinguishing so that the extinguishing gas alternatively by a Basic CMC entering the room can penetrate the racks Doors 1 2 3 4 The Control Unit can activate as many as four Four terminals for up to four door locks Automatic Door Kits for the control of a maximum of Automatic Door Kits four doors where the CMC TC system can always The following assignment is recommended control two doors using one CMC
15. untry in which the system is installed and operated and the national regulations for accident prevention Also observe any company internal regulations work operating and safety regulations Use only original RITTAL products or products recommended by RIT TAL in conjunction with this product Do not make any changes to this product other than those described in these or associated operating and installation instructions The operational safety of the product is guaranteed only for its approved use Under no circumstances should the technical data and the specified limit values be exceeded This is especially true for the specified ambient temperature and IP protection category The Control Unit must not be opened The unit does not contain any parts that need servicing Operating the system when it is in direct contact with water corrosive substances or flammable gases and vapours is prohibited The CMC TC system must be disconnected from the power supply when the Control Unit is connected with an I O unit a Basic CMC or an LCP system Other than these general safety notes ensure you also observe the specific safety notes when the tasks described in the following chapters are performed 3 Device description 3 1 1 Automatic Door Control Unit All inputs and outputs of the Automatic Door Control 3 1 Components and function description Unit are located on the rear The following components belong to the complete Au
Download Pdf Manuals
Related Search