Operating instructions GAM v2-03_english
Contents
1. Digital all settings which affect Outputs the digital outputs SIG Inquiry The GSM alarm module Signal Signal responds with the Strength signals strength The first number indicates a value between 0 31 31 max signal strength CONF DVTXT FCM HB Inquiry Returns all usual PFE PFTXT CON configuration values to POE POTXT PWE Figuration the GSM alarm module The PFE and PFTXT parameters only exist for GAM 2 Rights The Administrator AN on the GAM can operate all settings and make all inquiries Non Administrators TN1 TN5 can only use the commands ST DO x and the commands given under DOTXTO DOTXT1 as well as the Free Call Mode FCM which is currently set Bauser GmbH amp Co KG D 72186 Empfingen Troubleshooting Error Possible cause Possible solution LED Power remains dark No supply voltage LED GSM No SIM card blinks cyclically No contact with SIM card 2x from the PIN of SIM card deactivated beginning LED GSM blinks cyclically 3x from the beginning PIN not 1234 LED GSM on No GSM network available permanently no antenna connected LED Err blinks No configuration SMS has yet every second been sent factory default GAM does not Wrong number react toa AN already registered Configuration No given SMS Scope of delivery Connect to power supply Insert SIM card Clean surfac2. Time delay of the digital input until a xxxxx 120 new alarm SMS is sent The number of alarm SMS can be limited with this command for example if the input is unstable Example DITB1 3600 Alarm SMS are sent a maximum of every 3 600 seconds lt text gt Alarm Input n Setting the alarm text of the digital inputs Example DITXT1 Open front gate From now on the GAM will respond with GAM 1 DI1 1 Open front gate GAM 2 DI1 when digital input 1 is switched on Switch in order to deactivate auto x 1 matic transmission of an SMS when there is an input on Digital In 1 This means that the pure inquiry function can be used Example DIS1 0 Switches automatic SMS transmission off when DI1 is acti vated DIS1 1 Switches automatic SMS transmission on when DI1 is acti vated Switch in order to deactivate auto x 1 matic transmission of an SMS when there is an input on Digital In 2 This means that the pure inquiry function can be used Example DIS2 0 Switches automatic SMS transmission off when DI2 is acti vated DIS2 1 Switches automatic SMS transmission on for when DI2 is activated Sets relay output Example DO 1 Closes the relay contact The LED DO goes on DO 0 Opens the relay contact The LED DO goes off Bauser GmbH amp Co KG D 72186 Empfingen GAM GSM Alarm Modem Operating instructions GAM December 2007 Comma
3. must be entered into the telephone book by means of TN1 TN5 You Page 5 of 9 Bauser GmbH amp Co KG D 72186 Empfingen Bauser GmbH 2007 Subject to alterations Update http www bauser control de Operating instructions GAM December 2007 GAM GSM Alarm Modem Command Text Description Basic settings Command Text Description Basic settings Syntax Syntax can discover the correct number by rameter PWE calling a device which can show the incoming call number from the PWE x Password Activation and deactivation of x 0 desired landline telephone Enable password protection Normally lt Dialling code gt lt Tele phone number gt x 0 1 Warning Make sure that you It can happen with some telephone know the password which has systems that a leading 0 is dis been set when you activate played Please leave this out password protection Further commands can only be given if Example landline number the password is entered The N1 074851810 password must stand at the start Example mobile phone number of every further SMS followed by TN1 4916012345678 a semicolon If you have forgotten the pass PIN Xxxx PIN Change Changing the SIM card PIN number x 1234 word the only solution is to reset with the RESET button page 4 Xxxx Warning After resetting the GAM 0000 9999 to factory default by operating the Example 4 digits RESET button or by means of the PWE 1 RESET command the GAM Activation of
4. Update http www bauser control de
5. depending on your GSM network operator Inserting the SIM card You need an enabled SIM card from a GSM network operator to use the GAM The PIN must be set to 4234 Use a normal mobile phone in order to set the PIN Please see the operating instructions of your mo bile phone on how to change the PIN Before you insert the SIM card to the GAM please check whether you can send and receive SMS with a normal mobile phone If you have any problems to send or receive SMS please contact your provider for this issue If you have inserted a SIM card with a different PIN than 1234 the GAM will use a wrong PIN each time it switches on which means that your PIN will be blocked after three attempts If this happens you must assign a new PIN to your SIM card using the Super PIN PUK Please read the relevant section of your mobile phone operating instructions for setting the PIN or for resetting a blocked PIN with the PUK Update http www bauser control de Before opening the front cover ensure that all wires have zero potential Pay attention on safety instruc tions Open the front cover with a screwdriver Then lay the SIM card into the SIM card holder of the GAM see Fig 2 Push the cover of the SIM card holder slightly and open it up Push the SIM card into the cover hinge it shut and slide to lock Please comply with the orientation of the SIM card especially the position of the angled cor ner Close the fron
6. page 6 Page 3 of 9 Bauser GmbH 2007 Subject to alterations Update http www bauser control de Operating instructions GAM December 2007 GAM GSM Alarm Modem The GAM returns to the basic settings The LED Err starts blinking once per second The GAM can be newly configured by sending the con figuration SMS Pressing the RESET button during operation does not trigger a reset to factory default Extended configurations The GAM can be configured very flexibly via SMS for more complex tasks e g configuration of several authorised users for sending and receiving messages changing standard texts setting password protection and a whole series of further parameters All commands are described in detail along with exam ples in the SMS Command Table None of the commands are case sensitive i e all commands can be sent in upper or lower case All commands are given in upper case in the examples Each command must be ended with the semicolon Several commands can also be sent in one SMS Please note that not more than 160 characters can be sent in one SMS and that no spaces are allowed be tween the semicolon and the following parameter Extended example DVTXT myGAM HB 60 POTXT activated Effect Sets the device name to myGAM the heart beat to 60 min and the Power On Text to activated The GAM will issue the message myGAM activated DI1 x DI2 x DO x when it is powered on and will
7. password protection expects a SIM card with the PIN PWE 0 number 1234 Deactivation of password protection If a different PIN than 1234 is set the GAM will use a wrong Example Set DO if PWE 1 and PIN each time it is switched on PW ABCD ABCD DO 1 which means that your PIN will be blocked after three attempts ST Status Inquires the status of GAM Example PIN 9876 Example ST Sets the PIN number to 9876 Response GAM 1 DI1 0 DI2 0 DO 0 GAM 2 DI1 PFE x Power Fail Activation or deactivation of Power x 1 Enable Fail SMS RESET RESET Resets the GAM to factory default This parame same effect as operating the ter is only x 011 Example RESET button see page 4 and available with PFE 0 compare the right hand column of GAM 2 Deactivation of Power Fail SMS this Table PFE 1 Activation of Power Fail SMS Example RESET PFIXT Power Fail Setting of Power Fail Text lt text gt Warning JReseting WinRESET lt text gt Text This text is sent when the GAM 2 is Power Lost eRi ern Gr SUIS oss mek eee 3 3 the PIN of the SIM switched off if the Power Fail SMS This parame lt text gt PFE is activated ter is only max 32 available with characters Example PFTXT deactivated Extended example GAM 2 PIN 1234 RESET AN Effect Sets the current PIN includ POE x Power On Activation or deactivation of Power x 1 ing that of the SIM to 1234 Enable On SMS Default loads the default data and registers the tr
8. send a status message every 60 minutes see chapter SMS Commands SMS Commands Command Table Command Text Description Basic settings Syntax AN Administra Configuration command after tor Number switching on for the first time The GAM stores the telephone number which is calling once as an Administrator number and sends back the current status Other participants can only be established using this telephone number The same applies to changing of the basic settings It is only possible to delete this number with the RESET command page 6 or by operating the RESET button compare page 4 after switching on the GAM Update http www bauser control de Command Text Description Basic settings Syntax Example AN Response GAM 1 DI1 0 DI2 0 DO 0 GAM 2 DI1 DITDn xxxx Digital In Time Delay 1 3600 s DITBn xxxxx Digital In Time Blocked n 112 XXXXX 5 65535s DITXTn lt text Digital In gt 7 DIS1 x DIS2 x DO x Page 4 of 9 Bauser GmbH 2007 Subject to alterations Text n 1 2 lt text gt max 32 characters Digital In1 SMS enable x 0 1 Digital In2 SMS enable x 0 1 Digital Out x 0 1 Time delay of the digital input until xxxx 1 an Alarm SMS is sent Example DITD1 10 Alarm SMS is sent if the digital input is activated for 10 seconds DIn SMS se orton orTon HF DITEN
9. BAUSER Operating instructions GAM December 2007 GAM GSM Alarm Modem Introduction The GAM is a GSM alarm modem which is easy to install and to use It is suitable for low cost remote con trol in industrial and private facilities management e g in order to monitor heating and air conditioning and cooling systems lifts and escalators It is also possible to control machines and various types of devices Using the GAM it is possible to monitor two digital inputs and switch a relay by means of a normal mobile phone Up to 5 further telephone numbers can be stored in the GAM by means of the Administrator These numbers receive an SMS message from the GAM if a fault oc curs or if the inputs are activated The device can be configured and commissioned sim ply and without any software tools or programming knowledge Apart from the GAM you only need an activated SIM card from any network operator e g T Mobile D1 Vodafone D2 E Plus O2 Types of device This documentation contains the operating instructions and technical information with regard to device types GAM 1 and GAM 2 GAM 2 contains an internal NiMH rechargeable battery as an addition This means that the GAM 2 is able to send an SMS if the power supply fails or to report a power supply failure Warning The internal rechargeable battery of the GAM 2 is empty when it is delivered to the customer Con nect the GAM 2 to the power supply for charging for 24 h
10. EE For replacement please open the discon nected device from the bottom side Put a screw driver into the four lateral recesses between side plate and bottom plate to unlock the snap in hooks Disconnect the battery and remove it The device will be destroyed thereby Bauser GmbH amp Co KG D 72186 Empfingen GAM GSM Alarm Modem Operating instructions GAM December 2007 Technical Data GAM 1 ea 2 Power supply Ue Power consumption Ps Digital inputs Signal voltage 0 for inputs Signal voltage 1 for inputs Max contact load cos 1 Max contact load EMC acc EN 61000 6 2 and EN 61000 6 3 Ambient temperature Storage temperature Wave band Power Class Terminals Screws Conductor cross sections rigid flexibel with sleeve Humidity 40 C IDC V DC V DC V IAC V A DC V A PC PC Imm Imm 10 30 10V ripple lt 1 30V ripple lt 10 35 4 5 2x digital inputs 2 wire connection galvanically isolated 2 2 8 30 1250 5 30 5 lobserved 30 to 75 20 to 50 40 to 85 20 to 50 GSM 850 900 1800 1900 MHz GSM 850 900 4 2W GSM 1800 1900 1 1W Pozidriv size1 min 1 5 max 4 min 1 max 2 5 10 to 95 During power up the device and during sending a SMS message the currency can reach a short term peak of up to 1 A Bauser GmbH amp Co KG D 72186 Empfingen Bauser GmbH 2007 Subject to alterations Page 9 of 9
11. ansmitting x 0 1 Example POE 0 mobile telephone as Administrator Deactivation of Power On SMS number POE 1 Activation of Power On SMS TNn Telephone Sets a telephone number in the lt number gt Numbern telephone number list POTXT Power On Setting of Power On Text lt text gt i i Di lt text gt Text This text is sent when the GAMis Power On n 1 5 Itis possible to establish 5 additional switched on if the Power on SMS telephone numbers lt text gt POE is activated In parallel to the Administrator max 32 number these telephone numbers characters Example POTXT activated receive a status message from the GAM when an input DI1 or DI2 is PW lt text gt Password Changing the password lt text gt ABCD activated or can inquire the status iia by means of ST In addition it is lt text gt 4 Warning Make sure that you do possible to set the DO output and characters not forget the password which use the preconfigured FCM has been set However the configuration cannot If PWE 1 commands can only be be changed read only function given if the password is entered compare Rights page 7 If you have forgotten the pass word the only solution is to reset 4 with the RESET button page 4 Example mobile phone number TN1 4916012345678 Example PW Dcba Password is converted to DCBA A mobile number must start and upper or lower case can both be the country code and may have a used maximum 16 digits The pa
12. d on devices components or assemblies if it has been ensured that the devices are disconnected from the supply voltage and that electrical charges which are stored in the components contained in the device have been discharged beforehand Cables or leads which carry voltage to which the de vice the component or the assembly is connected must always be investigated for insulation faults or breaks If a fault is found in the supply line the device must be taken out of commission immediately until the defective line has been replaced When using components or assemblies users must always be reminded to adhere strictly to the character istic data for electric magnitudes stated in the relevant description If it is not clear to a non commercial end user from an existing description which electrical character istic data apply to a component or a module how external wiring is to be undertaken and which ex ternal components or additional devices may be connected and which connection values these ex ternal components may have always contact a technical expert for information Before commissioning a device a general check should be made as to whether this device is fundamentally suitable for the application for which it is to be used If there are any doubts it is essential to contact trained engineers or technical experts on the devices used Please note that operating errors and connection faults lie outside our sphere of inf
13. e Call the SMS to all the numbers entered in GAM will hang up the phone imme the telephone list AN TN1 TN5 diately You will only hear one every 60 minutes ringtone if Free Call is successful DOTXTO Digital Out Alternative text in order to switch the lt text gt OFF 0 Freecall switched off lt text gt Text DO 0 output to 0 relay open 1 Freecall activates the output lt text gt The effect of the command is This behaves depending on how max 16 equivalent to DO 0 DOP and DOT are set characters Here you can define a command For example if DOT 2sec the yourself output returns to its original state 2 seconds after activation If Configuration example DOP 1 the output is negated DOTXT0 close gate 2 Freecall toggles the output Application example If it is O itis switched to 1 and CLOSE GATE vice versa upper or lower case can both be f DOT was configured the out used Do not forget the put returns to its original state after this time If DOP 1 the Effect DO output of the GSM alarm output is negated module is switched off The relay is opened 3 equivalent to ST A status SMS is requested Warning Make sure that you do not use any text which has Warning The telephone which is already been allocated For calling must be able to receive the example AN is already allo Status SMS cated to an SMS command Landline numbers can also be used in conjunction with Freecall These
14. e of SIM card Activate PIN of SIM card with a mobile phone Reset GAM to factory default see page 4 and set the PIN of the SIM card to 1234 with a mobile phone Change antenna position Connect antenna Send configuration SMS See page 3 Configuration SMS Check number SET button reset configura tion see page 4 Please see page 3 Con figuration The following items are included in the delivery e GSM Alarm Modem GAM 1 or GAM 2 e Operating instructions Accessories e GSM GPRS antenna MMCX m Connector o Magnetic mount antenna or o Stickable patch antenna e Power pack 230VAC 24VDC a Following connection of the supply voltage GSM Alarm Modem needs approximately 30 40 seconds in order to start the GSM module Fol lowing this the LED Err is lit up for about 5 seconds turns off and than on for another 20 30 seconds Now the error check takes place Page 7 of 9 Bauser GmbH 2007 Subject to alterations Update http www bauser control de Operating instructions GAM December 2007 GAM GSM Alarm Modem A Safety Instructions When handling products which come into contact with electrical voltage the currently valid VDE stipulations must be observed especially VDE 0100 VDE 0550 0551 VDE 0700 VDE 0711 and VDE 0860 Before opening the device always disconnect the device from the main power supply and ensure that all connected wires have zero potential Tools may only be use
15. luence Understandably we cannot accept any liability whatso ever for damage injuries arising as a consequence Devices which are operated using a voltage gt 35 Volt may only be connected by a trained engineer Update http www bauser control de Operating Conditions Bauser GmbH 2007 Subject to alterations Where devices have an operating voltage gt 35 Volt final assembly may only be undertaken by an expert and it must comply with VDE stipulations When installing the device ensure that the connec tion cables have an adequate cable cross section If condensate forms it is necessary to wait for an acclimatisation period of up to 2 hours Liquids chemicals etc must be kept away from the device The device is intended for use in dry clean rooms Protect the device from moisture sprayed water and the effects of heat Do not expose the device to strong vibrations Do not use the device in an environment where there is an impermissible level of electromagnetic force Do not operate the device in an environment in which combustible gases vapours or dust are pre sent or could be present The device may only be repaired by an expert If the device has to be repaired only original spares may be used Use of any other than the original spares can lead to serious injury to persons or dam age to property GAM 2 At the end of life time the battery has to be disposed separately according directive 2006 66 EG WE
16. nd Text Description Basic settings Command Text Description Basic settings Syntax Syntax DOP x Digital Out Defines the standard polarity of the x 0 DOTXT1 Digital Out Alternative text in order to switch the lt text gt ON Polarity digital output relay contact lt text gt Text DO 1 output to 1 relay closed x 0 1 0 output relay contact is open after lt text gt The effect of the command is switching on the GAM LED DO max 16 equivalent to DO 1 off characters Here you can define a command The relay contact is closed for yourself example by command DO 1 LED DO on Configuration example If a time was set with the DOT DOTXT1 Open gate command the relay contact is opened again after this time Application example OPEN GATE 1 Output relay contact is closed upper or lower case can both be after switching on the GAM LED used Do not forget the DO on The relay contact is opened for Effect DO output of the GSM alarm example by command DO 0 LED module is switched on The relay is DO off closed If a time was set with the DOT command the relay contact is Warning Make sure that you do closed again after this time not use any text which has already been allocated For DOT xxxxx Digital Out Setting possibility for automatic reset xxxxx 0 example AN is already allo Time of the output after xxxxx seconds cated to an SMS command Monoflop functionality XXXXX DVIXT De
17. on 1 No AN yet see page 3 second off configuration 2 x short on No SIM card inserted device not locked into GSM or PIN of the SIM card deactivated 3 x short on Wrong PIN Off GAM ready Page 1 of 9 Bauser GmbH 2007 Subject to alterations Update http www bauser control de Operating instructions GAM December 2007 GAM GSM Alarm Modem Initial Use Instructions These operating instructions contain important information on the initial use and handling of the GAM Please read them carefully before using the GAM If damage arises which is caused by not complying with the operating instructions no claim shall be accepted under the warranty We do not accept liability for any consequential damages which may result We will not accept any liability if damage is caused to property or injury to persons because of inappropriate handling or disregarding the safety instructions No claim under the warranty whatsoever shall be accepted in such cases The GAM is fitted with highly integrated modules These electronic components are very sensitive to discharges of static electricity because of their technol ogy Please ensure that you are earthed when inserting the SIM card if possible Avoid touching the pins of compo nents on the printed circuit board While the GAM is operating depending on the ap plication GSM text messages SMS can be sent automatically as a consequence of which you may incur charges
18. ours when you first receive it Chapters and notes which only apply to the GAM 2 are identified accordingly Use for the intended purpose The use for which the device is intended is remote inquiry of the inputs and generation of SMS messages following activation of the inputs It is also possible to switch the GAM relay contact on and off by remote control via the GSM network Any other uses than those just described are not permissible and are not for the intended purpose Do not use the GAM for safety relevant control functions Bauser GmbH amp Co KG D 72186 Empfingen Connections and LED displays e syControl GAM2 GSM Alarm Modem Err L s O power OM bi 00 Fig 1 Connections As can be seen in Fig 1 the GAM has 4 pairs of screw type terminals Occupancy Clamp Power 1 2 Power supply connection DI1 3 4 Opto decoupled digital input 1 DI2 5 6 Opto decoupled digital input 2 DO 7 8 Relay contact The GSM antenna is inserted in the antenna socket MMCX m connector LED Display If the device is connected to the mains power supply the LED Power lights up As soon as the module is logged into the GSM network the LED GSM will wink every 2 seconds The LEDs DI1 and DI2 signal the state of the digital inputs The LED DO lights up if the relay is activated Meaning of the LED Err On Booting or error Blinks 1 second
19. owing this GAM sends an Alarm SMS to your mo bile phone Receipt GAM 1 DI1 1 Alarm Input 1 GAM2 DI1 Please note that it takes around 6 seconds to send an SMS Time delay between triggering of the event and receipt of the SMS is due to the GSM network Status inquiries Send the following SMS to the GAM ST The GSM alarm module responds with the current status GAM 1 DI1 0 DI2 0 DO 0 GAM 2 DI1 Power Lost Message The Power Lost message is only sent with the GAM 2 Disconnect the GAM 2 from the power supply The GAM 2 has a rechargeable battery which powers the device if the external power supply fails e g in case of a power cut As soon as the GAM 2 recognises such a condition it begins to send a Power Lost message You will receive the following message to your mobile phone GAM 2 Power Lost The GAM 2 switches off after sending the SMS Power On Message After this reconnect it to the power supply You will receive the following message to your mobile phone GAM 1 Power On DI1 0 DI2 0 DO 0 GAM 2 Power Resetting to factory default Disconnect the GAM from the power supply Press the RESET button keep it pressed down and reconnect the power supply Keep the RESET button pressed down for at least 18 seconds When the reset is triggered the LED Err lights up for around 6 seconds 1 The Power On Lost Message will be sent to each phone number listed in the device AN TN1 TN5 compare
20. ssword can consist of any combination of characters and digits For details how to use it see Pa Page 6 of 9 Update http www bauser control de Bauser GmbH 2007 Subject to alterations Bauser GmbH amp Co KG D 72186 Empfingen Operating instructions GAM December 2007 GAM GSM Alarm Modem Command Text Description Basic settings Syntax TNCn Telephone Deleting a telephone number from Number the telephone list Clear Example TNC1 n 1 5 Deletes telephone number 1 from the telephone number list Remark The saving of the parameters of the GAM takes about 5 seconds Do not cut power lines during that time Inquiry commands As the GAM can be configured in a very individual way there is a possibility of inquiring with regard to settings Send one of the following commands and the GAM responds with an SMS with the content stated below in the Response column It is not possible to inquire the PW and PIN settings for reasons of security Command Text Description Response SMS Syntax TN Inquiry Inquires for all telephone AN TN1 TN2 Telephone numbers The GAM TN5 Numbers responds with the complete contents of the telephone book DI DIS1 DIS2 Inquiry The GAM responds with DITD1 DITD2 Digital all settings which affect DITB1 DITB2 Inputs the digital inputs DITXT1 DITXT2 DO DOT DOP Inquiry The GAM responds with DOTXT0 DOTXT1
21. t cover of the GAM noting the installation direction pe Fig 2 Antenna connection Insert the GSM antenna in the MMCX antenna socket Position the antenna at a location where you have a good GSM connection Tip You can check the quality of the connection with a normal mobile phone The phone SIM card must be from the same network provider After initiation the system with the start up SMS you can also check the signal strength with the command SIG see page 7 Power supply Connect the device to the power supply The LED GSM lights up permanently afterwards The GAM will now automatically try to log into the GSM network As soon as the GAM is logged into the GSM the LED GSM winks around every 2 seconds The LED Err blinks every second Page 2 of 9 Bauser GmbH 2007 Subject to alterations Bauser GmbH amp Co KG D 72186 Empfingen Operating instructions GAM December 2007 GAM GSM Alarm Modem Configuring the GAM Notation Meaning of the different text styles Normal Explanatory text Bold italics Text to be used to the GAM ina SMS Bold Response of GAM received by SMS Important information Please note All commands to the GAM must be ended with a semicolon Configuration SMS On delivery the GAM is configured by the configuration SMS after connecting up the power supply The GAM stores the SMS call number automatically and sends future events to this n
22. umber The entire GAM is therefore configured for simple applications with a single SMS during which it makes a note of the call number You do not need any additional software computer or programming knowledge Sent the following SMS to the GAM AN The LED Err stops blinking and turns off permanently The GAM responds with the current status GAM 1 DI1 0 DI2 0 DO 0 GAM 2 Di1 You can now operate the GAM by SMS from the known mobile phone The AN command can only be executed again after Resetting to factory default see page 4 and 5 None of the commands are case sensitive i e all commands can be sent in upper or lower case Tip We recommend that you store the call number of the GAM in the telephone book of your mobile phone Please note The incognito function on your tele phone must be switched off so that the GAM can identify the correct number Setting the output Send the following SMS in order to set the DO digital output DO 1 The DO output is switched on and the LED DO lights up Send the following SMS in order to reset the DO digital output DO 0 The DO output is reset and the LED DO goes off Bauser GmbH amp Co KG D 72186 Empfingen Please note the difference between the letter O and the number 0 Receiving Alarm SMS Connect digital input DI1 DIZ to a 24V power supply for at least one second Please follow the connection diagram Fig 1 on Page 1 Foll
23. vice Text Setting of device name lt text gt 0 65535 s If xxxxx 0 the output remains lt text gt This command is useful if you use GAM 1 permanently set and is only reset lt text gt several GAM devices and want to GAM 2 after the device has been switched max 16 differentiate between them on again or with the DO 0 com characters mand Example DVTXT myGAM sets device to myGAM Example DOT 10 If the output is switched FCM x Free Call The GAM offers the opportunity to x 0 with DO 1 at DOP 0 it is auto Mode trigger an action through calling up matically reset after 10 seconds the inserted SIM alone Because the x 0 1 2 3 GAM does not pick up and no actual Note connection is established this If one of the inputs is activated procedure does not cost you during the output is switched on an anything alert is sent via SMS This sending Please make sure that the answer of the SMS can enlarge the DOT ing machine is deactivated in the time to up to 6 seconds SIM inserted in the GSM alarm module or do not let it ring long HB xxxxx Heart Beat Automatic cyclic transmission ofa xxxxx 0 enough until it is answered as Status SMS otherwise your network operator will XXXXX The Heartbeat is switched off at charge you for the call 0 10080 XXXXX 0 Please note that the telephone min which is calling up has to communi 7days Example cate its call number HB 60 The GAM sends a Status Afer recognizing a Fre
Download Pdf Manuals
Related Search