Operating instructions
Contents
1. The BAUSER battery and time controller is delivered with mounting staff and plug connector Mounting The controller is applicable for flush mounting in a boarding dash or similar application Cutout 52mm optionally with adapter for cutout 60mm order code 735 rear view c hour counter input key operated switch relay Service hour counter g _ artiye DS p relay z aCTIve Ly An batte ry Key switch K hour counter input battery aaa L battery ace M adjustable potentiometer reset button option E Hour counter r 6 active o NL S z VW 4 Ae ii D 2 ZOND ee ee NS Electrical connection The instrument must be installed by an authorised specialist The relevant conditions must be observed in particular the operating voltage of the controller must agree with the rated voltage of the battery see rating plate Check the correct polarity of the relay contacts Function and operation 1 LED indication 2 red 3 yellow 5 green battery controller 2 LC display hour counter Technical data Operating voltage V tolerance 25 12 242. 36 Current consumption max mA 50 35 35 EMC emission EN 55011 immunity EN 50082 2 in case of excess voltages that are above the approved EMC EMI protection we recommend a shielding from custom s side Vibration EN 60068 2 34 1g 10 500Hz SAE J 1378 20g 10 80Hz Shock EN 60068 2 27 30g 18ms EN 60068 2 29 25g 6ms SAE 1378 55g 10 ms Relay contact opens when reaching discharge voltage voltage free breaking capacity 12VDC 5A 24VDC 5A 36VDC 3A 48VDC 2A Signal inputs minimum pulse duration 0 5 sec Display multicolor 10 bar LED display 2 red 3 yellow 5 green battery controller LC display 6 digits hour counter Counting range hour counter up to 99999 9h service counter option up to 9999h Time divergence max 0 02 Ambience 30 C to 70 C max 95 humidity Protection class IP65 frontal Bauser GmbH amp CoKG J ulius Bauser Str D 72186 Empfingen Tel 07485 181 0 Fax 07485 181 16 e mail mail bauser control de Internet www bauser control de 03 03 Rev 1 5
3. Operating instructions Battery and time controller Type 830 BAUSER Please note Read this operating instructions carefully In the event of questions please contact your dealer or BAUSER directly Pay attention to the battery manufacturer s information and ensure that the installation and operating conditions described below are observed since otherwise you may lose your warranty rights Note in particular the information on the valid protection conditions in the section Electrical connection or the protection regulations applicable in your country Type Function 830 battery and time controller 830 1 battery and time controller with integrated service counter Functions The BAUSER battery and time controller of type series 830 monitors the residual capacity at discharge of traction batteries and it also registers operating hours An additional relay contact protects the battery against exhaustive discharge Optionally the controller can be delivered with integrated service counter The controller is adjustable to the different battery types by the exhaustive discharge voltage via potentiometer on the rear of the unit In order to activate a new adjustment the unit has to be reset The factory set standard discharge voltage is 1 73 V cell When choosing another adjustment we recommend to verify the correct discharge voltage The residual capacity of the battery is monitored via a multi LED display 2 red 3 yellow 5 green LEDs If the r
4. esidual capacity falls under the limiting value pre warning one red LED starts flashing When reaching the discharge voltage the 2 red LEDs flash alternatively and the relay contact pins 3 4 opens In order to complete e g a lifting operation the relay contact can be closed one more time for approx 30s by switching the key operated switch off and on There are 2 possibilities to reset the controller battery is separated from the vehicle Reset voltage is 2 09V cell reset voltage has to be exceeded for approx 4 sec battery remains in the vehicle while charging The unit tracks battery recharge and even recognizes not fully charged batteries Battery recharge is indicated via flashing LEDs In order to activate a new potentiometer adjustment a battery voltage of 2 35V cell has to be exceeded The operating hours are indicated by a LC display Type 830 1 The current status of the service down counter is indicated for a period of 5 sec every time the unit is turned on or the key switch is turned on resp After termination of the service time Service counter 0 the service counting status is indicated in the LC display flashes The service counter is resetable via the reset button on the rear of the controller The key switch turns on the LEDs and relay and enables the hour counter inputs Exhaustive discharge voltage n V cell adjustable via potentiometer on the rear of the controller i ir ar a o l o l oes oe aan a a Delivery
Download Pdf Manuals
Related Search