Stinger 0136350 Use and Care Manual
Contents
1. magazine e Open Quick Clear nose if applicable remove jammed fastener and close latch e Load tool 4 Weak drive e Check to make sure there is adequate air supply 5 Skipping fasteners e Replace bumper if worn e Use only recommended fastener sizes e Replace magazine if worn e Check air supply as it may be too low 6 Fasteners will not drive e Increase air pressure do not exceed 120 completely into work piece PSI Please contact Inside Sales for technical support if you have any other problems 800 746 5659 Contact Inside Sales at 800 746 5659 to place an order for replacement parts Visit our website at to learn more about our products and services national nail corp more than just nails 2964 Clydon SW Grand Rapids MI 49519 USA Phone 800 968 6245 Fax 616 531 5970 z z 5 D o le 32. staple follower in and secure e Plug into air source Tool is ready to use www nationalnail com OPERATING THE TOOL 1 Do not use tool prior to reading the Owner s Manual 2 Read warning label s on the tool 3 Visually inspect the tool for worn or damaged parts 4 Wear appropriate eye and ear protection 5 Install a male pneumatic fitting into the end cap of the tool ensuring that the fitting allows the tool to exhaust any air in the tool when the air hose is disconnected 6 Add 2 drops of non detergent 20 weight oil into the male fitting 7 Connect the air hose using a quick connect fitting to the tool and check the air pressure reading on the regulator to ensure it does not exceed 105 PSI Check the tool for any air leaks 8 Place the tool empty of fasteners in operating position on a scrap work piece Fully depress the safety and pull the trigger to verify that the tool cycles 9 Disconnect the air hose from the tool when e Loading staples and or caps e Performing inspection maintenance or repair e Clearing a staple or collated cap jam e The tool is not in use e Leaving the work area e Moving the tool to another work location e Handing the STINGER CS58 to another person e Storing the tool 10 Following recommended loading instructions load the fasteners approved for use in the tool www nationalnail com STINGER CS58 OPERATING THE TOOL 11 Cycle the tool on a scrap work piece
3. to evaluate the depth of penetration by the fastener into the work piece 12 To adjust the depth of penetration regulate the air pressure at the regulator and or disconnect the air hose adjust the depth control screw connect the air hose and cycle the tool on a scrap work piece to evaluate the adjustment 13 Repeat Step 12 as needed to set the correct depth using the minimum amount of air pressure to drive the fastener Q 9 e lt E 2 a E z STINGER CS58 SCHEMATIC A I KE 1 3 f E AN iD ke E Dd A A SS 0 ER e e Hl attente enge BP Ah Y GOGOE DANS SOS o 6 bseap A Le ge W i en E Lex p _ TO uo a 17 K a j e wy Y y Wey e T WO Suey Re WY Oy wy el Ww 9 A CH D j j Y SK Da Do AN ei SY Q T A WA WII NN IN 7 A HI YSZ NY 12 14 07 www nationalnail com STINGER CS58 PARTS LIST Item No Ref No Description 136629 01 Screw 135851 02 Washer 136635 03 Exhaust Deflector 135853 04 O Ring 135854 05 Washer 135855 06 Cap Screw 135856 07 Flat Washer 135857 08 Cap 136627 09 Exhaust Seal 136628 10 O Ring 136630 11 Poppet Spring 135861 12 Poppet O Ring 135862 13 Poppet 135863 14 Piston Stop O Ring 135864 15 Cylinder Seal O Ring 135865 16 Cylinder Spacer 135866 17 Gasket 135867 18 Cylinder 135900 19 O Ring 1
4. 35868 20 Cylinder O Ring 135869 21 Cylinder Guide 135870 22 O Ring 135871 23 Piston O Ring 135943 24 Piston amp Driver Assembly 135872 25 Driver Blade 136621 26 O Ring 135874 27 Bumper 135875 28 Body 136664 29 O Ring 135877 30 End Cap 135947 31 Washer 135948 32 Belt Clip 135878 33 O Ring 135879 34 Trigger Valve A 4 Parts included in AS 97323 O Ring and Seal Kit www nationalnail com STINGER CS58 PARTS LIST Item No Ref No Description 135880 35 O Ring 135881 36 O Ring 135882 37 Trigger Valve B 135883 38 O Ring 135884 39 O Ring 135885 40 Spring 135886 41 O Ring 2 135887 42 Plunger 135888 43 Trigger Valve Housing 135892 44 Stationary Front Plate 135891 45 Screw 135893 46 O Ring 135896 47 Latch Assembly 135890 48 Return Seal 135944 49 Front Plate Assembly 136654 50 Pin 135895 51 Pin 135897 52 Safety Foot Guide 136658 53 Spring 135899 54 Safety 136653 55 Pin 135945 56 Safety Assembly 136623 57 Step Pin 2 135946 58 Trigger Assembly 136611 59 Washer 135906 60 Bracket 135907 61 Pin 135908 62 Cap Feeder 135901 63 O Ring 135909 64 Spring 135910 65 Feed Cylinder 135911 66 O Ring 135912 67 Feed Piston 135913 68 O Ring 4 Parts included in AS 97323 O Ring and Seal Kit www nationalnail com STINGER CS58 PARTS LIST Item No Ref No Description 135914 69 Spring 135915 70 Piston Stop 135916 71 Feed Piston Cover 135917 72 Retaining Ring 135918 73 Hold Down Spring 1
5. 35919 74 Magazine Right 135920 75 Magazine Cover 135921 76 Magazine Left 135922 77 Screw 135923 78 Nut 135924 79 Screw 135925 80 Feed Chute 135926 81 Screw 136608 82 Screw 135928 83 Magazine Cover 135929 84 Screw 135930 85 Wear Plate 135931 86 Screw 135932 87 Pusher 135933 88 Negator Spring 135949 89 Track 135934 90 Latch Cover 135935 91 Pin 135936 92 Spring 135937 93 Latch 135938 94 Magazine 135950 95 Pin 135939 96 Feed Chute Bracket 135940 97 Screw 135941 98 Washer 135942 99 Screw 136645 Barb Fitting 2 135904 Tubing Parts included in AS 97323 O Ring and Seal Kit www nationalnail com STINGER CS58 MAINTANANCE amp STORAGE MAINTENANCE 1 Disconnect the air hose from the tool when performing inspections maintenance or repairs 2 Use air line lubricators If lubricators are not available or if hose lengths exceed 10 feet add 2 drops of non detergent 20 weight oil daily into the air inlet of the tool 3 Whenever repairs or replacement of parts inside the body occur check the piston O ring for adequate grease lubrication 4 Never use any parts other than genuine STINGER replacement parts 5 Periodically clean the magazine and nose of the tool with a mild solvent STORAGE 1 Disconnect the air hose when storing the tool 2 Never store the tool in cold weather environments for any duration of time as any frost or ice formation in the tool will cause tool failures 3 F
6. national nail corp more than just nails S58 CAP STAPLER OWNER S MANUAL E d e E 2 S gt Revised 12 10 07 A N PLEASE READ This manual contains important information about product safety www nationalnail com TABLE OF CONTENTS e Important Information e Warnings e Tool Specifications e Loading the Tool e Operating the Tool e STINGER CS58 Schematic e STINGER CS58 Parts List e Maintenance and Storage e Warranty e Troubleshooting N O a N 10 13 14 15 www nationalnail com IMPORTANT INFORMATION Please take the time to read and understand the information contained in the Owner s Manual included with this product before operating or maintaining the STINGER CS58 Cap Stapler Improper use of this tool could result in serious injury or even death Most accidents occur because of the failure to observe basic safety rules and precautions Basic safety precautions are outlined in the Warnings section of this manual This product is intended for securing housewrap and roofing felt only Please do not use this pneumatic tool for applications other than those specified This manual should be available for anyone who plans to operate the tool www nationalnail com WARNINGS PERSONAL SAFETY ITEMS e Do not use tool prior to reading the Owner s Manual e Always wear eye protection that conforms to ANSI requirements 287 1 and provides protection again
7. ommended maximum operating air pressure as tool wear will be greatly increased The air supply must be capable of maintaining the operating air pressure of the tool Pressure drops in the air supply can reduce the tool s driving power e Use a pressure regulator and gauge to allow visual inspection of the air pressure being delivered to the tool Use air hoses that have rated pressures of up to 150 of the maximum pressure that can be generated by the power source The supply hose should contain fittings that will provide quick disconnecting from the male plug on the tool e Use quick connect fittings that allow the tool to be unhooked from the air supply quickly and easily e Do not use fittings that will not allow the tool to exhaust when the air supply is disconnected www nationalnail com WARNINGS OPERATION OF THE TOOL e Never inspect maintain repair adjust clear a jam or store the tool with the air connected e Never use the tool in proximity of flammable gases or liquids as some tools will create sparks that can be an ignition source for a fire or explosion Always inspect the safety device for damage and proper operation prior to operation e Never assume the tool is empty of fasteners e Never point the tool toward yourself or any other persons e Never cycle the tool unless it is in contact with the work piece e Never use the tool as a hammer or wedging device or drop to the floor from any height Alway
8. or prolonged storage add 2 drops of oil to the air inlet of the tool prior to discontinuing use Also clean the exterior of the tool with a mild solvent 13 www nationalnail com WARRANTY WARRANTY ITEMS 1 Warranty for cap assemblies castings and housing castings is one year 2 Warranty for bumpers O rings driver blades and piston rings is not applicable as they are normal wearing parts whose life is dependant on application 3 Warranty for all other parts is 90 days WARRANTY CONDITIONS 1 The beginning date in which the warranty is in force is the date of purchase 2 The warranty is not transferable 3 The warranty is voided by any of the following Abuse misuse or damage to the tool Use of parts other than genuine STINGER parts Use of fasteners not designated for use in the tool Modifications to the tool that alter the original function or intent of use of the tool by anyone other than National Nail Qo op 4 National Nail retains the right to replace or repair any warranty items it deems necessary www nationalnail com TROUBLESHOOTING Disconnect the air hose from the tool when performing inspections maintenance or repairs PROBLEM CORRECTION 1 Tool operates but no fasteners e Check magazine for proper fasteners are driven Fasteners should slide freely in and out of the magazine 2 Cap leaks air e Tighten cap screws 3 Fasteners jam in nose of tool e Remove fasteners from
9. s remove your finger from the trigger when pausing from cycling e Never tamper with the safety device or use the tool if the safety device is not functioning properly Use only 5 8 STINGER StaplePac cap fasteners with the STINGER CS58 Cap Stapler Never use any fasteners that are not specified for use in this tool The CS58 holds 1 coil of plastic caps 200 caps and 2 strips of staples 100 staples each www nationalnail com TOOL SPECIFICATIONS Operating pressure Weight Nail capacity Cap capacity Air inlet Fasteners 95 105 psi 3 9 Ib 200 staples 2 100 count strips 200 plastic collated caps 1 reel 3 8 NPT STINGER StaplePac National Nail product number 0136360 Consists of 20 strips of 5 8 20 gauge staples 100 staples per strip and 10 reels of 1 diameter plastic collated caps 200 caps per reel www nationalnail com LOADING THE TOOL e Disconnect air Open the magazine cover by pushing the green cover release tab and lifting Place cap reel in basket Make sure the front end of the cap coil is placed over the cap guide area of the basket Insert lead cap into the feed chute e Slide caps along the feed chute with fingers until they engage the cap feeder Pull the cap feeder back and release to advance caps until the first cap is under the nose of the tool Close the magazine cover Depress the latch on the staple follower and pull back Insert two staple strips Slide
10. st flying particles both from the front and side Eye protection should be worn by the operator and by others in the work area Eye protection is required to protect against flying fasteners and debris that could possibly cause severe eye injury e The employer is responsible to enforce the use of eye protection equipment by the tool operator and all other personnel in the work area e To prevent accidental injuries Handle the tool with care Always assume that the tool contains fasteners Always disconnect the air hose from the STINGER CS58 when e loading staples and or caps e performing inspection maintenance or repair e clearing a staple or collated cap jam e the tool is not in use e leaving the work area moving the STINGER CS58 to another work location e handing the STINGER CS58 to another person e storing the tool Never point the tool toward yourself or anyone else Never engage in horseplay Never hold or carry the tool with a finger on the trigger Never place a hand or any other part of the body in the fastener discharge area of the tool while the air supply is connected www nationalnail com WARNINGS AIR SUPPLY AND CONNECTIONS e Use only clean regulated compressed air as a power source for this tool Do not use bottle gases combustible gases or oxygen as a power source for the tool as the tool may explode e Do not use air supply pressures that exceed 105 PSI e Do not exceed the rec
Download Pdf Manuals
Related Search