Titan 0290005 Installation Guide
Contents
1. NOTE The spray gun and cables are mounted to the gun support bar at the factory NOTE Do not attach the tip to the spray gun yet Remove the tip if it is already attached 5 Position the spray gun a Loosen the support bar knob and slide the gun support bar to the desired horizontal position Make sure the gun is far enough away from the cart so that aii gt the rear wheel does not ama track over the fresh spray p a pattern Support b Loosen the gun riser bar knob clamp and slide the spray gun to the desired vertical position A distance of 6 from the tip to the spray surface is a good starting point NOTE The height of the spray gun affects the width of the spray pattern i e the lower the gun the smaller the line width Tip size also affects line width 6 Make sure the gun cable is operating properly When pulling the spray lever on the cart handle the gun cable should be pulling the trigger This cable is factory set to operate properly If adjustment to the gun trigger tension is required refer to the Adjusting the Trigger Tension procedure in the Maintenance section of this manual 7 Turn the PRIME SPRAY knob to the PRIME position IMPORTANT Never operate unit for more than ten seconds without fluid Operating this unit without fluid will cause unnecessary wear to the packings TM LULA English 8 Remove AutoOiler cap with a flat blade screwdriver Squirt Pist2. before the line striper stops produces an evenly painted line from start to finish If the striping path ends at an obstacle release the trigger at the same moment that the line striper stops moving Attaching the Tip Guard and Tip Use the following procedure to install the tip guard and tip to the spray gun 1 NOTE The arrow on the tip Perform the Pressure Relief Procedure described in this manual Using the arrow head on the tip handle insert the tip seal and tip seal retainer into the back of the tip guard Press in for final adjustment Insert the tip into the slot on the tip guard Thread the tip guard onto the gun Position the tip guard in the desired spraying position and tighten securely handle should be pointing in the forward direction for spraying
3. Operator Controls The following section describes the operator controls on the spray gun and line striper Spray Gun Trigger Lock Engage the trigger lock whenever the gun is not in use The gun is locked when the trigger lock is at a 90 angle perpendicular to the trigger in either direction NOTE If necessary loosen the gun holder clamp knob and then engage the spray gun trigger lock Move the spray gun to its original position and tighten the clamp knob Spray Lever The spray lever is located on the cart handle The spray lever controls the trigger on the spray gun Fully pulling the spray lever triggers Spray the spray gun While striping the ever spray lever should be fully pulled for proper operation DirectLink Spraying pressure is determined by the motor throttle The throttle is regulated by adjusting the DirectLink pressure control knob The higher the throttle the higher the spraying pressure PRIME SPRAY Knob The PRIME SPRAY knob switch directs material to the al material return tube when set we to PRIME or to spray hose PRIME SPRAY when set to SPRAY knob The arrows on the PRIME SPRAY knob shows the rotation directions for PRIME and SPRAY Shutoff Switch The engine shutoff switch will shut the engine off when it is running Press and hold the shutuff switch in order to shut the engine off Sureflo Valve The Sureflo Valve is designed to keep the inlet va
4. bucket holders on the cart Make sure the bucket holders hold the five gallon bucket securely Adjust the bucket holders using the thumb screw located underneath each holder if necessary NOTE When using this line striper for first time it may 10 11 12 13 14 15 16 17 18 19 be helpful to use water in place of paint to gain familiarity with the operation of the line striper After changing from water to paint test spray several lines on cardboard roofing felt or rosin paper before striping to ensure correct line width Place the siphon tube into the bucket of material Place the return hose into a metal waste container Turn the PRIME SPRAY knob to the PRIME position area Clockwise Fully depress the pusher stem to make sure the inlet ball is free Turn the DirectLink pressure control knob fully clockwise to minimum INS Co AN j he ra V i A 4 L xX Pe 7 T OS N A Start the engine Move the choke lever up to the full choke position Push the rubber prime button 7 10 times Pull the starter rope rapidly and firmly Continue to hold the rope as you let it return Pull and return the rope until the engine starts Once the engine is running slowly move the choke lever down to the closed position Slowly turn the DirectLink pressure control knob counterclockwise to increase the pressure until fluid starts to
5. come out of the return hose Use only enough pressure to keep the fluid coming out Allow the sprayer to run for 15 30 seconds to flush the test fluid out through the return hose and into the waste container Turn the DirectLink pressure control knob fully clockwise to minimum Turn off the sprayer by pressing and holding the engine shutoff switch until the motor shuts off Remove the return hose from the waste container and place it in its operating position above the bucket of material Start the engine Turn the PRIME SPRAY knob to the SPRAY position Unlock the gun by turning the gun trigger lock to the unlocked position Turn the DirectLink pressure control knob slowly counterclockwise to increase the pressure Fully pull the spray lever on the cart handle Fluid will begin flowing through the spray hose and out of the gun Continue to pull the spray lever on the cart handle until material is coming out of the gun Release the spray lever Choke lever Prime bulb Starter rope gt SPRAY AINIYd P Titan Tool Inc All rights reserved 20 21 22 23 24 A 25 26 27 28 Lock the gun by turning the gun trigger lock to the locked position If necessary loosen the gun holder clamp knob and then engage the spray gun trigger lock Move the spray gun to its original position and tighten the clamp knob Turn the DirectLink pressure control knob fully clockwis
6. e to minimum Turn the PRIME SPRAY knob to PRIME Turn off the sprayer by pressing and holding the engine shutoff switch until the motor shuts off Attach tip guard and tip to the spray gun Refer to the instructions later in this section POSSIBLE INJECTION HAZARD Do not spray without the tip guard in place Never trigger the gun unless the tip is in either the spray or the unclog position Always engage the gun trigger lock before removing replacing or cleaning tip Start the engine Turn the PRIME SPRAY knob to SPRAY Fully pull the spray lever on the cart handle to trigger the spray gun Test the spray pattern and line position on a long piece of roofing felt or cardboard Check for proper line width and position If adjustment to the position of the spray gun is required refer to the Setup procedure earlier in this section Make sure that the spray gun shuts off completely when the gun trigger is released If adjustment to the trigger tension is required refer to the Adjusting the Trigger Tension procedure in the Maintenance section of this manual Begin striping Position the line striper slightly in front of the striping path Start walking with the line striper and trigger the gun at the beginning of the striping path At the end of striping path release the trigger and continue walking a short distance if possible NOTE Triggering the gun after the line striper is moving and releasing the trigger
7. lve open and from sticking to dried materials The Sureflo Valve is activated manual by the user AutoOiler The AutoOiler is designed to provide lubrication to the fluid section of the pump After initial setup press the AutoOiler button 2 3 times before each use Titan Tool Inc All rights reserved Setup Perform the following procedure before starting the engine of a gas powered line striper This equipment produces a fluid stream at A extremely high pressure Read and understand the warnings in the Safety Precautions section at the front of this manual before operating this equipment 1 Attach the handle to the cart a Line up the hole in the bottom of the handle with the support Handle weldment on the cart oe adjustment b Thread the bolt through the knob hole in the handle and the weldment Tighten by turning the knob of the bolt clockwise c Position the handle at the desired height Loosen the knob on the rear of the support weldment in order to to loosen the handle d Pull the handle up or down to the desired height Tighten the handle knob in order to secure the handle 2 Make sure that the siphon tube and the return hose are attached and secure 3 Using a wrench thread the airless spray hose to the outlet fitting on the sprayer Tighten securely 4 Attach an airless spray gun to the spray hose Using two wrenches one on the gun and one on the hose tighten securely
8. on Lube into the AutoOiler Replace cap 9 Push AutoOiler button 2 5 times to lubricate the fluid section 10 Check the engine oil level The gasoline engine oil level is determined by the manufacturer Refer to the engine manufacturer s service manual Supplied 11 Fill the gas tank on the engine with unleaded gasoline only Do not mix the gasoline with 2 cycle oil Preparing to Paint Before painting it is important to make sure that the fluid in the system is compatible with the paint that is going to be used NOTE If this unit is new it is shipped with test fluid in the fluid section to prevent corrosion during shipment and storage This fluid must be thoroughly cleaned out of the system before you begin spraying Incompatible fluids and paint may cause the valves to become stuck closed which would require disassembly and cleaning of the sprayer s fluid section IMPORTANT Always keep the trigger lock on the spray gun in the locked position while preparing the system If necessary loosen the gun holder clamp knob and then engage the spray gun trigger lock 1 Place the siphon tube into a container of the appropriate solvent for the material being sprayed refer to recommendations of the material manufacturer An example of the appropriate solvent is water for latex paint 2 Place the return hose into a metal waste container 3 Turn the PRIME SPRAY knob to the PRIME position 4 Fully depres
9. s the pusher stem to make sure the inlet ball is free 5 Turn the DirectLink pressure control knob fully clockwise to minimum F 7 r iN 3 VI we AV L to 4 JA A SSX a N N E Vi N Fe 5 X N i lt X sL a y Clockwise 6 Start the engine a Move the choke lever up to the full choke position b Push the rubber prime button see N 7 10 times ENGI c Pull the starter rope rapidly Prime and firmly Continue to hold bulb the rope as you let it return Pull and return the rope until H the engine starts d Once the engine is running slowly move the choke lever down to the closed position NOTE If you are having trouble starting the motor rotate the DirectLink pressure control knob 1 2 turns counter clockwise UUL English Slowly turn the DirectLink pressure control knob counterclockwise to increase the pressure until fluid starts to come out of the return hose Use only enough pressure to keep the fluid coming out Allow the sprayer to run for 15 30 seconds to flush the test fluid out through the return hose and into the waste container Turn the DirectLink pressure control knob fully clockwise to minimum Turn off the sprayer by pressing and holding the engine shutoff switch until the motor shuts off NOTE Make sure that the spray gun does not have a tip 11 12 13 18 19 20 21 or tip g
10. uard installed Place a metal waste container underneath the spray gun to catch the solvent Start the engine Turn the PRIME SPRAY knob to the SPRAY position Turn the DirectLink pressure control knob slowly counterclockwise to increase the pressure Unlock the gun by turning the gun trigger lock to the unlocked position Fully pull the spray lever on the cart handle Fluid will begin flowing through the spray hose and out of the gun Continue to pull the spray lever on the cart handle until the old solvent test fluid is gone and fresh solvent is coming out of the gun Release the spray lever Lock the gun by turning the gun trigger lock to the locked position If necessary loosen the gun holder clamp knob and then engage the spray gun trigger lock Move the spray gun to its original position and tighten the clamp knob Check the entire system for leaks If leaks occur turn the sprayer off and follow the Pressure Relief Procedure in this manual before tightening any fittings or hoses Follow the Pressure Relief Procedure in this manual before changing from solvent to paint Be sure to follow the Pressure Relief Procedure A when shutting the unit down for any purpose including servicing or adjusting any part of the spray system changing or cleaning spray tips or preparing for cleanup Titan Tool Inc All rights reserved Painting ae Place a five gallon bucket of material between the
Download Pdf Manuals
Related Search