Hitch Haul HMXCR Instructions / Assembly
Contents
1. CRADLE STEP 2 Attach 2 bridge supports as shown and 2 ramp supports using 4 medium length bolts washers and nuts NOTE When mounting ramp supports make sure flat surface is up and the extra 3 inches is on the outside to support the ramp while transporting MEDIUM BOLTS amp NUTS BRIDGE SUPPORTS MEDIUM _ BOLTS amp NUTS RAMP SUPPORTS STEP 3 PLACING THE LONG BOLTS The carrier is designed to load the motorcycle from the left or right side using the ramp There are 3 sets of center holes and 1 set of upper holes on each cradle The large safety pins and clevis pins are used in the upper holes See FIG 5 The 4 long bolts are used in the cLEVIS center hole to support the motorcycle tires NOTE Depending on the size of your motorcycle some bolts may not be needed STRAP HOOK HOLES Not Shown A RAMP STORAGE f Ea PINS STRAP HOOK oneness Arie 2s HOLES OUNT pa IMPORTANT STEP The front tire of the motorcycle must rest down into the cradle and This step is needed in case a strap is broken or comes loose during transport A second safety pin is supplied Depending on the size of your motorcycle this pin may not be needed If this pin is not used secure the motorcycle tire with a strap not included Insert 2 receiver bar tube into the 2 receiver hitch and secure with a clevis pin Clevis Pin not included This carrier will only mount into a 2 receiver only With fee2. must be secured through tire before transporting motorcycle e Check all hardware connections nuts amp bolts before each use e For added theft security secure motorcycle with a lock and chain Not included MASTERBUILT MFG Inc PRODUCT WARRANTY MASTERBUILT Mfg Inc warrants all parts of this HITCH HAUL Motorcycle Carrier product to be free from defects in material and workmanship within one year from the date of purchase Within this period MASTERBUILT Mfg Inc shall correct any defect by repairing or replacing defective parts of the equipment or making available the parts thereof FOB Columbus GA MASTERBUILT Mfg Inc shall not be obligated to repair or replace equipment which has been repaired by others abused altered or misused We further state that we shall not be held liable for any loss due to neglectful use on the part of the operator Upon the expiration of such warranty all liability shall terminate No other warranties are expressed or implied NOTE Paint finish will scratch and chip under normal use and therefore carries no warranty To validate your warranty please complete Warranty Information and return to Masterbuilt Mfg Inc within 30 days of the date of purchase Visit Our Web Site www masterbuilt com Warranty Information Mail coupon or register online at www masterbuilt com Name Address City State Zip Dealer Name Location Date of Purchase Model Serial Cut out warran
3. AORN tgs MAS TERBUILT HITCH HAUL MOTORCYCLE CARRIER ASSEMBLY OPERATING amp SAFETY INSTRUCTIONS MODELS HMXCR HMXCRA Manual Code 900000140 090402 THIS PRODUCT IS FOR OUTDOOR USE ONLY Designed for 2 Receivers and Hitch Accessories ONLY Tools needed for assembly 2 Adjustable Wrenches 4 WARNINGS 4 e MASTERBUILT IS NOT RESPONSIBLE FOR DAMAGE DONE TO OR FROM MOTORCYCLE DUE TO MISUSE OF PRODUCT e THE HITCH HAUL MOTORCYCLE CARRIER IS INTENDED FOR OFF ROAD MOTORCYCLE USE ONLY e FAILURE TO FOLLOW THESE INSTRUCTIONS PROPERLY COULD RESULT IN INJURY e KEEP THIS MANUAL FOR FUTURE REFERENCE 4 WARNINGS 4 e Never exceed 500lb capacity or the receiver hitch manufacturer s tongue weight rating e Motorcycle carrier is intended for one motorcycle only e Do not attempt to drive motorcycle onto carrier platform e Always use the ramp to load and unload motorcycle e Always secure loading ramp while vehicle is in motion e Do not attempt to load motorcycle onto carrier if you have back joint leg or other health problems e Do not sit on motorcycle while on carrier e Do not start motorcycle engine while on carrier e Do not carry flammable items on carrier e Motorcycle must be in gear while on carrier e Motorcycle carrier is not intended for transporting humans e Motorcycle MUST be secured with ratchet style straps while being transported straps not included e Safety bolts and clevis pins
4. t firmly planted and motorcycle in neutral slowly guide motorcycle up loading ramp onto carrier Use two people if necessary The loading ramp can be used on either side of carrier Make sure lip of ramp is securely hooked into ramp mount
5. ty information and return in an envelope to MASTERBUILT Mfg Inc 1 Masterbuilt Court Columbus GA 31907 ATTN Warranty Department PARTS LIST MOUNTING AND LOADING MOTORCYCLES Bam 2 Spring Cip iia E Secure motorcycle with 2 ratchet Place the ramp onto the style straps not included Put receiver tube as shown one of the safety pins into upper allowing the center support hole passing through the spokes to slide into the bracket of the front wheel Secure with a Secure with 2 spring clip clevis pin See FIG 5 Bridge Support 2 Receiver Bar LARGE SAFETY PIN Ramp Support REPLACEMENT PARTS If you need help or if parts are missing do not return to dealer Contact Masterbuilt at 1 800 489 1581 Reciever Bar Kit Carrier Half Kit FETH AEFI r AELE 2 LARGE SAFETY PINS WITH HOLE amp CLEVIS PIN mih mg 4 MEDIUM LENGTH BOLTS WITH OET NT LOCKING NUTS amp WASHERS LOCKING NUTS amp WASHERS r p 4 Bridge Support Kit 4 BENDING PIN 1 2 SPRING CLIP ASSEMBLY INSTRUCTIONS STEP 1 Place tire cradles inside support channel on receiver bar Attach with 8 short bolts washers and nuts There are 4 nuts bolts and washers per cradle Note The washer is placed onto the bolt first and then inserted from the inside out The nut goes on the outside of the support channel SMALL BOLTS amp NUTS Tye SUPPORT CHANNEL amp 2 RECEIVER BAR
Download Pdf Manuals
Related Search