Northwest 80-2000A-36 Instructions / Assembly
Contents
1. 54 Screw ST4 8 Plastic expansion Tool required Magnetic Phillips Screw Driver Product Dimensions DDDDDDDDDDDDDD 457 80 2000A 54 U cs _ a O cr lo lt r S a a a a a Ga OAIN NTANOTNIITT AANA 1372 1208 Before Assembly Before you assemble your fireplace you should put the crystals on the ember Please following below 1 Put the fireplace on flat floor with the front glass panel on top position 2 Use screwdriver not supplied to loosen the 7or 9 screws as Fig A and remove the glass panel 3 Put the craystals gently on the ember as Fig B 4 Tighten the glass panel with the 7 or 9 screws tightly 5 Use screwdriver not supplied to loosen the 2 screws as Fig C and remove the hanger Fig A INSTALLATION 1 This heater is for wall mounting only Do not attempt to use it free standing 2 Referring to Fig 3 below select a suitable position in which to mount the heater horizontally use a spirit level to achieve this 3 Check the wall to ensure there is no wiring pipe wires etc in the area to be drilled Drill 4 holes 8mm diameter amp 40mm depth using a suitable size drill and put the Plastic expansion into the holes 4 First fix hanger to wall 5 Referring to Fig 4 hang fireplace to hanger 6 Referring to Fig 5 avoid fireplace to move use screw fix fireplace to wall Warning Always ensure the fireplace is at least 200mm above2. ELECTRIC FIREPLACE INSTALLATION AND OPERATING INSTRUCTIONS Model 80 2000A 36 80 2000A 42 80 2000A 54 Retain this manual for future reference Read these instructions completely first before installing and using Failure to follow them could cause a heater malfunction resulting in serious injury and or property damage WARNING Electric heaters are hot inside Do not use it in areas where gasoline paint or flammable liquids vapors are or stored WARNING All electric heaters have hot inside Do not use it in areas where gasoline paint or flammable liquids vapors are or are stored Ad cauTION Do not expose the heater to the elements such as rain etc Due to high temperatures the heater should be located out of traffic and away from furniture and draperies Do not place clothing or other flammable material on or near heater Never place any objects on the heater Carefully supervise young children when they are in the room with the heater Heater becomes very hot when running Keep children and adults away from hot surfaces to avoid burns or clothing ignition Heater will remain hot for a time after shutdown Allow surfaces to cool before touching IMPORTANT INSTRUCTIONS When using electrical heaters basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read all instructions before using this heater 2 Keep combus
3. aximum is reached To decrease the brightness press and release the Ay 9 button Each time you press this button the brightness will decrease by small amount until the minimum brightness is reached u Del 7 HEA w O Button To activate the heater press the heater button Heater work at the high press the Heater Button once to turn off the heater TEMP HIGH LOW OFF HIGH heater work with 1500W HEATER LED for RED LOW heater work with 750W HEATER LED for Blue TEMP HEATER LED for Purple Adjusting to auto control by room temperature the heater turns on and work with 1500W when roomemperature is below 22 C the heater turns on and work with 750W when roomemperature is below 25 C and above22 C the heater will turn off when the room temperature is above 25 C 8 To turn the stove off press the 5 button once Notice This remote control must remain within 6 metres of the fireplace and not too far off to either side to be effective TROBULESHOOTING GUIDE Ad caution Turn off the appliance and let it cool before servicing it Only a qualified service person should service and repair the heater PROBLEM Stove turns off and will not turn on Flame is not moving Flame sputters Log set and or Flame is not glowing Remote control does not work CAUSE Stove has overheated and safety device has caused thermal switch to di
4. htness Press and release the FLAME control button to cycle through LO MED HI and OFF Operating by Remote Control Fig 6 1 Plug in your electric fireplace Important The Main ON OFF power switch on the fireplace must be in the ON position 2 When operating the heater with the remote control it must be pointed at the logset inside the electric stove and the red light must blink each time you press a function button The blinking red light confirms the remote control is working Note Make sure your batteries are installed correctly in your remote control 3 C button of the remote control at the top left is the main ON OFF power button I 4 vO buttons is on off button to control the red and blue lamp of flame and ember bed 5 The Red dls 9 or 7 9 buttons control the red brightness of flame and ember bed To increase the brightness press and release the dls 5 button Each time you press this button the brightness will increase by a small amount until the maximum is reached To decrease the brightness press and release the Ay 0 button Each time you press this button the brightness will decrease by small amount until the minimum brightness is reached 6 The BLUE Als 9 or 7 9 buttons control the blue brightness of flame and ember bed To increase the brightness press and release the Ale 5 button Each time you press this button the brightness will increase by a small amount until the m
5. let receptacle Never use with an extension cord or relocatable power tap outlet power strip 16 To prevent a possible fire do not burn wood or other materials in this heater 17 To prevent electric shock or fire always use a certified electrician should new circuits or outlets be required 18 When transporting or storing heater keep in a dry place free from excessive vibration and damage 19 The heater must not cover up an electrical socket the socket must always be accessible in order to disconnect the heater from the electrical supply for maintenance and cleaning 20 This heater must be grounded The main supply must be Safely routed from the heater to an electrical socket Note When the heater is turned on for the first time it may release a slight harmless odor or smoke This odor or smoke is a normal occurrence caused by the initial heating of the internal heating elements and should not occur again SAVE THESE INSTRUCTIONS Technical Specification ELECTRIC FIREPLACE Model 80 2000A 36 80 2000A 42 80 2000A 54 Rated Voltage 120V Description of product Rated Frequency 60 Hz Rated Power 1500W Lamp LED Unpacking and Testing 1 Carefully remove the unit from the box Prior to using the unit test to make sure the unit operates properly Plug the unit s power supply cord into a conveniently located 120volt grounded outlet Check to see the unit turns on and produces function WARNING Do not operate
6. sconnect or home circuit breaker has opened Flame motor defective Flame motor Is defective Ember LED PCB are burnt out Wiring is loose Low batteries CHECK e Reset switch by turning main power switch off and waiting 5 minutes then turning it back on e Call a qualified service technician to replace flame motor Call a qualified service technician to replace flame motor Inspect LED PCB and replace it if necessary Inspect wiring for loose connections and repair or replace if necessary e Replace new batteries in remote control
7. the floor Be sure that the bolts have been fixed firmly enough to withstand the weight Fig 5 OPERATION Remove all packaging before use Control Panel See also Operating Instructions below As shown in the photo below you will see the control panel in the right side of the heater HEAT FLAME c HEATER POWER Fig 6 1 Power switch 2 Heat control button 3 Flame control button 4 Heater LED 5 Power LED Operating by manual Plug the heater in to a suitable main outlet See rating label on unit for power requirements 1 Power Switch ON OFF Set this switch to position l to turn the product ON Setting it to O to turn the product OFF Turn on the fireplace the Power LED will be lighten 2 Heat control button Push the HEAT button to cycle through as bellow TEMP a HIGH LOW OFF HIGH heater work with 1500W HEATER LED for RED LOW heater work with 750W HEATER LED for Blue TEMP HEATER LED for Purple Adjusting to auto control by room temperature the heater turns on and work with 1500W when room temperature is below 22 C the heater turns on and work with 750W when room temperature is below 25 C and above22 the heater will turn off when the room temperature is above 25 C 3 Flame control button Push the FLAME control button to adjust the flame height and ember bed brig
8. the unit if it is damaged or has malfunctioned If you suspect the unit is damaged please contact customer service The appliance is employed a manually reset thermal cut out for safeguard if it operates please inspect for any objects on or adjacent to the heater which may cause high temperatures DO NOT OPERATE THE HEATER UNTIL TROUBLESHOOTING Reset switch by turning main power switch off and waiting 5 to 10 minutes then turning it back 2 This heater is for use on 120 volts The cord has a plug as shown at A in below Figure An adapter as shown at C is available for connecting three blade grounding type plugs to two slot receptacles The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box The adapter should not be used if a three slot grounded receptacle is available f f f f aa Fog rs fs F N a Fi A E i WA meS s j A pe metal screw L ee SS a t ie i ie b j x Cae 2 di z 5 NSSS COVER OF GROUNDED l UM a ner et f A Ha OUTLET BOX GROUNDING siege i A CB A en i ADAPTER _ KEN f P 3 Ne m rA a oR NI gt f a F A o amp O j amp LC ocd i Parts and hardware Remote Control Manual Fixing Hanger In the back of i the fire Fixing Bracket Crystals 1or 2 80 2000A
9. tible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet from front of heater and keep them away from sides and rear 3 Always unplug heater when not in use 4 Do not operate any heater with a damaged cord or plug or after heater malfunctions has been dropped or damaged in any way 5 Do not use outdoors 6 This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container 7 Do not run cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 8 To disconnect heater turn controls to OFF before removing plug from outlet 9 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater 10 To prevent possible fire do not block air intakes in any manner 11 Use this heater only as described in this manual Any other use is not recommended by the manufacturer which may cause fire electric shock or injury to people and or animals 12 Always use properly grounded fused and polarized outlets 13 Always use ground fault protection where required by electrical codes 14 Always disconnect power before performing any cleaning maintenance or relocation of heater 15 Always plug heaters directly into a wall out
Download Pdf Manuals
Related Search