SPT WA-1140DE Use and Care Manual
Contents
1. DUAL HOSE PORTABLE AIR CONDITIONER USE AND CARE MANUAL WA 9040DE WA 9040DH WA 1140DE WA 1340DE WA 1340DH Thank you for purchasing SPT Air Conditioner please read the Use and Care Manual carefully before installing and using this appliance Keep this manual for future reference CONTENTS Table of Contents Introduction Features Identification of Parts Unit Accessories and Window Kit Installation Instructions Control Panel Remote control Operating Instructions Operating modes Cooling Dry Smart mode Timer settings Setting the clock Super and Heater Protection Features Maintenance Troubleshooting Specifications Warranty Info Notes oO o o a A O 10 11 12 13 13 14 15 16 17 18 19 20 Introduction Thank you for choosing this portable air conditioner It will provide you and your family with all of the Home Comfort requirements for your home cottage or office This appliance can be moved from room to room within your home and set up in just minutes Electrical Specifications 1 All wiring must comply with local and national electrical codes and be installed by a qualified electrician Contact a qualified electrician with questions regarding the following instructions 2 Check available power supply and resolve any wiring problems before installation and operation of this unit 3 For your safety and protection this unit is grounded through the power cord plug when plugged into a m2. 5 SWING BUTTON e Press once for vertical swing of the louver e Press again to set the louver at a desired position 6 SMART BUTTON Press to enter fuzzy logic operation regardless if unit is ON or OFF 7 TIMER ON BUTTON Used to set or cancel timer on function 8 TIMER OFF BUTTON Used to set or cancel timer off function 9 HEATER BUTTON for Heating models only Used to start or stop electrical heating mode SUPER BUTTON for Cooling only models Used to start or stop fast cooling function KEY all buttons exist and correspond to the control panel except SUPER SMART amp SWING Used to regulate Signal transmit A Auto fan speed temperature in Smart or Dry A Smart indicator ake High fan speed mode see page 12 Smart 3 Cooling indicator on Low fan speed Mode for details 8 Dry indicator pB Displays set Indicator of Timer ON or 68 99 Timer OFF and displays real temperature fica Heater indicator available for models with heater only Note Each mode and relevant function will be further specified in following pages g ujug gt 98 909 How to Insert Batteries e Remove the battery cover according to the arrow direction e Insert new batteries making sure the and match accordingly e Slide the cover back in position Note e Use 2 AAA 1 5 volt batteries e Replace batteries with new ones of the same type when the display becomes dim Using the Remote C
3. by High 4F 2 4F Low Press once to raise the set temp by High Slightly chill 1 2F Low Increase the temperature High up to 2 4F Press once to raise the set temp by p 2 4F Low Uncomfortable due to air Changes the FAN speed Auto High Low flow volume only applicable in SMART amp COOL mode Press once to swing press again for fixed airflow direction Uncomfortable due to air Note There is no SWING button on the control panel To activate flow direction or deactivate swing from the control panel press and hold FAN button for 3 seconds 12 Timer ON and Timer OFF settings Timer ON and Timer OFF are convenient features for those who would like the unit to start and stop after a certain time you can set the unit to turn ON After 5 hours When you return your home will have achieved a comfortable temperature Or before going to bed you can set timer OFF to have the unit turn off after so much time Timer ON setting 1 Press the TIMER ON button once You should see the ON indicator flash for 0 5 seconds and the time displaying 12 00 2 Press the A or V button to increase or decrease your set time Each press is an increment of 10 minutes Press and hold down the buttons to speed up the process 3 The set time clock is in 24 hours format Maximum timer setting is within 24 hours 4 Once the set time is achieved press TIMER ON button again To cancel Timer On setting e Press and hold the TIMER
4. ON button for 3 seconds Timer OFF setting e Follow the instructions as Timer On setting but use TIMER OFF button Once the time for Timer ON or OFF is set the unit will memorize the set time unless power is disconnected If you wish to set Timer ON or OFF for the same time in a future day simply press the Timer ON or Timer OFF button twice If unit is unplugged Timer settings will return to default Adjusting real time setting the clock Real time can be adjusted while unit is off or running in any mode Press TIMER ON and TIMER OFF buttons together Clock will flash for 0 5 seconds and display 12 00 Adjust the real time by pressing the A or Wbutton Each press is in increment of 1 minute Press and hold the A or V button and time will adjust in increments of 10 minutes 13 SUPER mode SUPER mode applicable for Cooling only models SUPER mode is used to start or stop fast cooling Press SUPER and unit will operate at high fan speed and automatically changing the current set temperature to 18 64F SUPER mode can be entered while unit is in operation or off You can adjust airflow direction and set timer in SUPER mode To escape from SUPER mode press any of the following buttons SUPER MODE FAN POWER or temperature A or V buttons Display will return to the original setting mode Note SMART button is not applicable in SUPER mode Unit will continue to run in SUPER mode high fan at 18 C 64 F until you pre
5. atching wall outlet If you are not sure whether the wall outlets in your home are properly grounded please consult an electrician Do not use plug adapters or extension cords with this unit If it is necessary to use an extension cord use with heavy appliance extension cord only available at most local hardware stores Energy Saving Tips Please use the unit in the recommended room size Refer to www spt usa com Do not locate the air conditioner where furniture or other objects can obstruct the airflow Keep blinds curtains closed during the sunniest part of the day Close the fireplace damper and floor or wall grills so that cool air does not escape through the chimney or ductwork Keep the exhaust hose as short and straight as possible e If unit is to be operated throughout the day turn on the unit early before the noon heat hits e It is highly recommended to turn on the air conditioner when the room temperature is around 75f Do not wait until the room gets excess ively hot e Keep the filters clean Single Hose vs Dual Hose Single Hose draws indoor air for both front cold air output and exhaust air to cool compressor PROS e Fresh air is exchanged CONS e Fresh air will delay the soeed of ambient temperature drop Dual Hose draws indoor air for front cold air output and outdoor air for exhaust air If outside temperature is lower than ambient compressor cools down faster and produces colder air output Ambi
6. be a malfunction Please check the following suggestions before asking for service Problem Possible cause and resolution Unit does not run e Check if the protector trip or fuse is blown e Please wait 3 5 minutes before restarting delay protection may be preventing the unit to run E e Check if batteries in the remote controller need replacing e Check if the plug is securely plugged in Compressor runs for short period of e Check if set temperature is too close to ambient time and stops temperature If so lower the set temperature e The air outlet may be blocked by obstacles remove obstacles e Check if the air filters are dirty e Check if outdoor temperature is too high e There may be doors or windows open e There may be other appliances creating a heat source in the same room heater lamp computer etc e Air filter is dirty please clean e Air outlet or inlet is blocked e Set temperature is higher than ambient temperature e Inner water reservoir is open top Move the unit by pushing gently and evenly on the side e f possible drain water before moving Unit does not run and red light is flashing e Water reservoir is full Remove rubber plug and drain water 17 Specifications ae nf ee ee ee eee Heating capacity BTU hr a ea a ae 4 100 w a Humidity removal capacity pints day ee aa a a M s Net weight 82 lbs 86 lbs Gross weight 88 lbs 93 lbs Data may var
7. bove set t emperature HIGH fan speed COOLING mode COOLING mode with AUTO Fan Ambient temp Ambient temp decreasing increasing 20 4F 1 2F Compressor ON Set temp 10 2F Compressor OFF Set temp 2 4F 1 2F 2 4F 10 DRY mode To use the unit as a dehumidifier remove moisture operate the unit as follows e Press MODE button to select DRY mode e You can also select DRY mode while unit is powered off Once DRY is selected press the POWER button and unit will start in DRY mode e Adjust the louver direction by pressing SWING button if desired When unit is first initiated in DRY mode as the compressor kicks on unit will run in COOL mode with settings at 18 64 F for 3 minutes This al lows the unit to determine the ambient temperature After 3 minutes unit will automatically set the target temperature to be 1 50 3F below ambient You cannot change the set temperature and fan speed in DRY mode NOTE e DRY mode cannot be used to cool the room e Requires only air exhaust hose to be installed Do not install the air intake hose e In DRY mode fan speed is pre set at Low and cannot be changed The FAN button is invalid in this mode Delay Protection If you select COOLING or DRY mode while unit is running in another mode the compressor will be delay protected Wait for 3 5 minute and unit will resume operation Do not press any button during the wait time or unit will re count
8. delay NOTE e If the air conditioner is running in COOLING or DRY mode with an open door or window for a long period of time when relative humidity is above 80 dew may collect and drip from the outlet e Once unit is unplugged all setting will return to default including Timer ON and Timer OFF settings Water Drainage In COOLING and DRY operations water is condensed as air passes through This unit is equipped with Self Evaporating Technology where most of the water is recycled and evaporated through the exhaust hose In humid conditions however when water condenses faster than the unit can recycle the excess water will collect within an inner water reservoir When the water reservoir becomes full the Water Full indicator will flash red light and unit will stop At this time you will need to drain the water reservoir before continuing operation Turn unit off and unplug from power source Move the appliance to a suitable place for water drainage Push gently on the side to prevent water spilling Pull out the rubber plug and allow water to drain out Re inserted the rubber plug when done Make sure the rubber plug is replaced or water will leak If the unit is placed in a position allowing water drainage connect the drain hose to the spout for water drainage 15 Maintenance Cleaning the AC unit Cleaning the Air Filter Turn off unit and remove power source lt is necessary to clean the air filter after approx
9. e the desire height is set insert a small screw not supplied to keep in place e Do not block the air outlet or intake with protective grid curtain shutter or other obstacles e Keep a minimum clearance of 8 between the ends of air hoses e Try to keep the air hoses as straight as possible as in Figure 3 Installation Sequence 1 Select a suitable location with easy access to an electrical outlet 2 Install the flexible air hoses and adjustable slider kit as depicted in Figure 3 e For COOLING mode please install both the air intake and air exhaust hose Cooling capacity will decrease when using single air hose However to prevent compressor from overheating when outdoor temperature is 35 95f or above remove the air intake hose e For DRY mode remove air intake hose and install only the air exhaust hose For FAN and HEATER Heating models no hose installation required Plug unit to a grounded electrical outlet Please select an appropriate power supply based on the requirements on the nameplate 4 Press the power buiton to turn unit on Note Do not use an extension cord with this appliance If an extension cord must be used use heavy appliance extension cords only Available at most local hardware stores Control Panel U HEATER WATER Full M Pag ON OFF button to start or stop the appliance MODE button to select the operating mode Smart Cooling Dry gt Fan only FAN bu
10. ent temperature drops quickly Same air circulating within the room resulting in decreased oxygen level and increased carbon dioxide If outside temperature is too high compressor cannot be cooled resulting in increased temperature of front air output NOTE It is suggested to remove the air intake hose and use as single hose system when outside temperature is over 95F Features This unit is equipped with the following features e Re Start IC Should there be a power outage when power returns unit will resume operating at last setting mode e Self Evaporating Technology Recycles the condensed water and evaporates it out with the exhaust air for added cooling efficiency as well as energy efficiency e Smart Mode fuzzy logic operation e Super Mode for cooling only models e Heater Mode for units with heater option Identification of Parts Unit Control panel Air outlet louver Remote signal receptor Remote controller Transport handle Air exhaust hose Evaporator air intake Air intake hose Drain port er LO e r SY a ee I 0 Power supply The images in this manual are based on the external view of a standard model Consequently the shape may differ from that af the air canditinner voi have calactad Accessories Installation Accessories Window patio door slider kit PART amp DESCRIPTION QUANTITY 1 Air inlet hose 1pc Extends from 17 3 4 to 70 5 8 Air inlet hose Window exhaust adapte
11. imately 100 hours of usage or whenever the filters appear dirty Turn appliance off before disconnecting from power IF 1 Turn off unit Remove the air filter by supply pulling the frame upwards se a dry and oft cloth to clean it Clean the air filter i e Tap the filter lightly to remove Never use volatile substance such as nae sae y gasoline or polishing powder to clean the i e Vacuum the filter appliance e f extremely dirty wash the filter in lukewarm water and allow to dry completely in a shaded place before replacing Never spray water directly onto the main unit key fy Dangerous 3 Clean the air filter once every two Electric shock weeks if the unit is operating in an extremely dusty environment Preparing the unit for storage If the unit will not be used for a long period of time follow the below instructions for unit storage 1 Drain water from the reservoir and replace rubber plug Connect to power source and run unit in FAN only mode for 4 6 hours on a sunny day This will allow the unit s interior to dry and prevent molding Turn unit off and remove power source Remove batteries from the remote and store ina safe place Clean the air filters and replace Remove the two air hoses and store them properly Cover the hose openings on the unit Place unit back in original packaging if available Store in a cool dry place 16 Troubleshooting The following cases may not always
12. lude freight charges Incidental or consequential damage caused by possible defects with this product Damage to product caused by improper power supply voltage accident fire floods or acts of nature Failure of product resulting from unauthorized modifications to the product Improper installation or failure to perform the necessary maintenance This GUARANTEE is in addition to your Statutory Rights SUNPENTOWN INTERNATIONAL INC 14625 Clark Ave City of Industry CA 91745 Tel 800 330 0388 Fax 626 336 7116 service sunpentown com www spt usa com 19
13. ontroller e To operate the air conditioner aim the remote controller at the receiver window e The remote control will operate the air conditioner at a distance up to 23 feet when pointed at the receiver window Operating Instructions Operating modes MODE Selection Each time the MODE button is pressed unit s operating mode is changed in sequence UNIT Smart Cooling Dry gt Fan only REMOTE Cooling Dry Fan only FAN Selection Each time FAN button is pressed the fan speed is changed in sequence Auto High Low Note e In FAN only mode only High and Low fan speeds are available e In DRY mode airflow is set at Low FAN button is ineffective in this mode Temperature Setting A Each press raises the temperature setting by 1 2 F V Each press lowers the temperature setting by 1 2F Temperature Range COOLING 18T 64F 320 90F Room temperature 2 4F FAN ONLY Unable to set Power ON Press button Once the unit receives the signal the RUN indicator on the air conditioner will light up HEATER SUPER SMART DRY TIMER ON and TIMER OFF operating modes will be specified in the following pages e When changing modes during operation allow 3 minutes for compressor to kick on e Wait 3 minutes before restarting the unit after powering off 9 COOLING mode To lower the room s ambient temperature operate the unit as follows 1 Pres
14. r Air outlet hose 1pc ani TH AINE Extends from 17 34 to 70 5 8 AW Window exhaust adapter 2pcs Adapter 2pcs Window patio door slider kit 1 set 3pcs From 28 3 8 up to 55 5 8 Adapter Window Kit Installation The window kit has been designed to fit most standard windows with vertical or horizontal applications However it may be necessary for you to improvise or modify some aspects of the installation procedures for certain types of windows Please refer to Figures 1 and 2 below for minimum and maximum window openings ae e Window slider kit Window slider kit minimum 28 1 3 72cm minimum 28 1 3 72cm maximum 55 1 8 140cm maximum 55 1 8 140cm FIGURE 2 FIGURE 1 Installation Instructions Selecting the best location e Best to place the unit near a window patio door or French window The shorter you can keep the intake exhaust hoses the more efficient the unit will run e Keep a minimum space of 20 inches between the back of the unit to the wall or other obstacles Installing instructions 1 Install the adapters and window exhaust adapters to the hoses Fix the adapter end of the hose to the unit Extend the hose to the destined window door to insure enough clearance Attach hose to slider kit Repeat above steps for the other hose D n pN Install the slider kit to the window door and adjust height accordingly There are small openings on the side of the slider kit Onc
15. s MODE button to select COOLING mode 2 Press FAN button to select desired fan speed 3 Press the temperature A or VW button to set desired temperature NOTE e The above settings can also be done while unit is powered OFF Once you complete the above steps press the POWER button and unit will start in COOLING mode e You can adjust the louver direction by pressing the SWING button Press once to swing and press again to stop Press and hold the FAN button on the control panel for swing e Unit will memorize your last setting for Cool when powered off or switched back from other modes Will return to default if unplugged e Once the room temperature reaches the set temperature the compressor will stop and fan will continue to run Unit operates 1C 2F of set temperature When operating in COOLING mode compressor continues to run until ambient temperature has reached 1 2f below the set temperature Compressor will then stop and unit will run in FAN mode Once unit detects the ambient temperature has rise 1 2f above se t temperature compressor will resume For example your set temperature is 70f Compress or shuts off and unit switches to FAN at 68f and resumes cooling at 72F AUTO FAN speed selected in COOLING mode e When initial ambient temperature is higher than set temperature HIGH Fan speed e When ambient temperature falls below the set temperature LOW fan speed e When ambient temperature rise 30 6f a
16. ss any of the buttons mentioned above SUPER mode does not exist for models with Heater HEATER mode HEATER mode for heating model only Press HEATER button to engage unit in Heater mode If unit is off pressing the HEATER button will turn unit on and operate in Heater mode Press FAN button to change fan speed High Low Timer ON or Timer OFF can be set in heating mode To escape from HEATER mode press the HEATER button again Unit will engage in fan only mode Note e HEATER can be selected while unit is running in other modes e Temperature cannot be set in HEAT mode e Temperature A and VY buttons are invalid in Heater mode 14 Protection Features Operating Conditions and Protection Features The protective device may trip and stop the unit in the following cases Mode Situation Reason Action When outdoor temperature Compressor COOLING is over 43 109F overheat use unit as single hose When ambient temperature Cooling coils Compressor will not work is below 18 64 F freezing below 18 64 F DRY When ambient temperature Cooling coils Compressor will not work is below 18 64 F freezing below 18 64 F The protective device will also engage in the following cases e Restarting the unit immediately after operation stops or changing mode during operation Please wait 3 5 minutes e Turning on the unit immediately after connecting to power source There may be a 20 seconds
17. the delay protection time 11 SMART mode Press the SMART button to enter smart mode fuzzy logic operation In this mode the temperature is automatically set based on the room s ambient temperature If unit is OFF pressing the SMART button will turn the unit on and operate in SMART mode There is no SMART button on the control panel To select SMART from the control panel press MODE button Smart Cooling Dry Fan only Unit will automatically determine the operating mode COOL or DRY when SMART mode is selected Operating Ambient temperature eae Target temperature 1 50 3 lower than 26 79F or below DRY ambient temperature after 3 minutes Over 26 79F COOLING 266 79F e FAN speed can be changed if unit runs in SMART amp COOL mode Press FAN button to change in turn Auto High Low e FAN speed cannot be changed if unit runs in SMART amp DRY mode The LCD displays as in image on the right but in fact the fan speed is preset and cannot be changed SMART button is ineffective in SUPER mode Note Temperature airflow and direction are controlled automatically in SMART mode However you can choose to increase or decrease the temperature by up to 2T 4F A increase or decrease up to 2 4F can be set i n SMART mode You feel Press Adjustment procedure Slightly warm ress once oe set temp by Decrease the 2T Low temperature up to 20 Press twice to lower the set temp
18. tton e Selects the fan speed Auto gt High Low e Press and hold to start or stop auto swing of louvers D TIMER ON button to set or cancel the timer on operation TIMER OFF button to set or cancel the timer off operation TEMP TIMER buttons to set clock to set timer or to adjust temperature setting Press A Y buttons together to switch temperature display C to F or vice versa RUN indicator lights up green when unit is operating WATER FULL indicator lights up red when water reservoir is full HEATER SUPER button e HEATER on Heater models turn heater on or off e SUPER on Cooling only models to enter or exit SUPER fast cooling mode LCD display displays temperature and mode settings The LCD display on the unit corresponds to the LCD display on the remote except for ambient temperature display Temperature Display On unit When flashing displays the set temperature e When steady displays the ambient temperature Only displays the set temperature Remote Controller The remote controller transmits signals to the main unit 1 ON OFF BUTTON To turn the unit ON or OFF 2 MODE BUTTON Used to select the operating mode 3 FAN BUTTON Used to select fan speed in sequence Auto High Low 4 TEMPERATURE SETTING BUTTONS e Used to set the desired temperature e Used to set clock or set timer e lf the A V buttons are pressed together temperature display will switch between and
19. y for technical reasons please refer to the rating label e Please read this manual thoroughly before installing and using your new portable air conditioner e Un insulated rooms such as sunrooms garages or attics should be less than the suggested sq ft e The following may effect the cooling efficiency of the unit in reaching your set temperature outside temperature room size ceiling height room insulation number of people in the room direct sunlight and sources of heat e Measuring conditions for above is COOLING RT 80 6 f RH 60 HEATING RT 68f RH 60W without hose connection RT room temperature RH room humidity 18 fel Portable Air Conditioner Your Guarantee If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase it will be repaired free of charge This guarantee is subject to the following terms Sunpentown must be notified of the fault Proof of purchase must be presented to Sunpentown s nominated representative The warranty will be void if the product if modified misused or repaired by an unauthorized person The warranty after repair will not be extended beyond the original one year period All replacement parts will be new or reconditioned Parts which are replaced become the property of Sunpentown The warranty applies for the use of the product in the USA only What is NOT COVERED Warranty does not inc
Download Pdf Manuals
Related Search