Home Decorators Collection 1981500410 Instructions / Assembly
Contents
1. HOME DECORATORS COLLECTION HDC 19815 MFG TW 19721DW NOBLE FILE CABINET 30 Hx21 5 W DISTRESSED WHITE ASSEMBLY INSTRUCTIONS Note Before assembly please be sure to work on a soft flat surface to avoid any damage to the finish Made In China TA P 1 9 BEFORE ASSEMBLY IMPORTANT NOTE READ CAREFULLY BEFORE ASSEMBLY TO PREVENT DAMAGE TO PARTS Following instruction listed below in the proper seguence as numbered to assure fast easy and correct assembly ASSEMBLY TOOLS REOUIRED DA Screw driver Rubber Mallet WOODEN DOWEL INSTALLATION PROCEDURE 1 FILL HOLE 1 4 FULL OF GLUE 0 8 2 GENTLY TAP DOWEL INTO HOLE cu WITH RUBBER MALLET OR USE HAND PRESS IN DO NOT USE HAMMER 3 WIPE AWAY EXCESS GLUE oe lex AA HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT amp LOCK PIN 1 SET INCLUDES C CAM LOCK 1PC A CAM BOLT IPC TOOL NEEDED SCREW DRIVER STEP 1 SCREW CAM BOLT A ONTO PRE SET PLASTIC NUT ON PANEL USE A SCREW DRIVER FOR TIGHTENING ATTENTION DO NOT OVER TIGHTEN THE CAM BOLT A STEP 2 ATTACH BOTH PANELS MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE HOLE WITH RUBBER MALLET GENTLY CAUTION DO NOT USE HAMMER THEN INSERT CAM LOCK C INTO PRE DRILLED HOLE ON PANEL MAKE SURE THE ARROW ON CAM LOCK C SET IN PANEL POINT TOWAR2. DRAWER FRONT PANEL DRAWER BACK PANEL DRAWER LEFT SIDE PANEL 1 PC 1 PC 1 PC D A C DRAWER RIGHT SIDE PANEL DRAWER BOTTOM PANEL LEFT SIDE FRAME 1 PC 1 PC D F RIGHT SIDE FRAME BACK PANEL ACROSS BAR 1 PC PC pP 1 PC G I ACROSS BAR SHELF TOP PANEL PC PC PC J L NOTE THE SURFACE WITH THE STICKER IS THE BACK SIDE P 4 9 STEP 1 ASSEMBLE DRAWER e USE SCREW 6 TO ATTACH DRAWER SIDE PANEL amp D AND BACK PANEL TOGETHER e INSERT THE DRAWER BOTTOM PANEL E INTO SLOTS OF SIDE PANEL C amp D USE CAM BLOT amp CAM LOCK 2 TO FIX DRAWER SIDE PANEL C amp D AND DRAWER FRONT PANEL A USE ROUND BOLT 5 TO ATTACH KNOB 5 ONTO DRAWER FRONT PANEL A P 5 9 STEP 2 RELEASE GLIDES PULL THE LEFT RIGHT INNER GLIDES FROM THE OUTER GLIDES UNTIL EXPOSING A SMALL BLACK SAFELY RELEASE TAB PUSH THE SAFETY RELEASE TAB THEN SEPARATE THE INNER GLIDE FROM THE OUTER GLIDES SAFETY RELEASE TAB STEP 3 ASSEMBLE SLIDE 4 USE FLAT HEAD SCREW 4 TO ASSEMBLE THE SLIDE 4 ONTO DRAWER SIDE PANEL C amp D P 6 9 STEP 4 ASSEMBLE SLIDE 4 USE FLAT HEAD SCREW 4 TO ASSEMBLE THE SLIDE 4 ONTO SIDE FRAME amp C STEP 5 ASSEMBLE SHELF AND ACROSS BAR I amp J e FILL RELEVANT HOLES 1 4 FULL OF
3. D THE HOLE INTO WHICH THE CAM BOLT A HAS BEEN INSERTED AND INSERTED THE CAM LOCK C TO THE VERY DEPTH OF THE HOLE STEP 3 ROTATE THE CAM LOCK C CLOCKWISE TO SECURE CAM BOLT A BY TIGHTENING WITH A SCREWDRIVER DETAIL STEP PLEASE SEE THE BELOW PICTURE P 2 9 VERTICAL CONNECTION HORIZONTAL CONNECTION 2 1 2 A S 3 4 la 4 C THANK YOU FOR PURCHASING THIS QUALITY PRODUCT BE SURE CHECK ALL PACKING MATERIAL CAREFULLY FOR SMALL PARTS WHICH MAY HAVE CAME LOOSE INSIDE THE CARTON DURING SHIPMENT COUNT ALL PARTS AND MATERIAL HARDWARE COMPARE WITH PARTS LIST TO BE SURE ALL PART ARE PRESENT IF ANY PARTS ARE MISSING OR DAMAGED PHONE FAX OR MAIL TO OUR CUSTOMER SERVICE DEPARTMENT FOR EFFICIENT AND SPEEDY SERVICE PLEASE INDICATE THE MODEL NUMBER AND CODE LETTER OF PART NEED IMPORTANT NOTE FOLLOW INSTRUCTIONS LISTED BELOW IN PROPER SEQUENCE AS NUMBERED TO ASSURE FAST EASY AND CORRECT ASSEMBLY HARDWARE LIST WOOD DOWEL CAM BOLT ROUND HEAD BOLT SLIDE 8 PCS CAM LOCK FLAT WASHER FLAT HEAD SCREW 4 SETS SPRING WASHER 2 SETS M 8 SETS D G Q VS v a KNOB FLAT HEAD SCREW ALUMINUM BAR ROUND HEAD SCREW ROUND HEAD BOLT 4 PCS 2 PCS 12 PCS SET G 5 6 0 8 ALLEN KEY GLUE 1 PC 1 PC 9 10 P 3 9 PARTS LIST
4. GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE ROUND HEAD SCREW SPRING WASHER AND FLAT WASHER 3 TO ASSEMBLE ACROSS BAR I amp J AND SIDE FRAME F amp G TOGETHER P 7 9 STEP 6 ASSEMBLE TOP PANEL L FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE ROUND HEAD SCREW SPRING WASHER AND FLAT WASHER 3 TO ASSEMBLE SIDE FRAME F amp G AND TOP PANEL L TOGETHER STEP 7 PLACE DRAWERS PULL OUT SLIDES INSIDE OF THE SIDE PANELS PROPERLY HAVE THE DRAWER TO MATCH SLIDE AND THEN SLIDE THEM INTO THE PRODUCT BODY GENTLY PUT THE 2 ALUMINUM BARS 7 INTO THE SLOTS INSIDE OF THE DRAWER P 8 9 STEP 8 ASSEMBLE BACK PANEL USE ROUND HEAD SCREW 8 TO ATTACH BACK PANEL M ON THE BACK OF PRE ASSEMBLED UNIT NOTE BEFORE YOU ASSEMBLE THE BACK PANEL PLEASE MAKE SURE THE 2 SIDE PANELS HAVE AN EVEN GAP BETWEEN THEM UNEVEN SHIFT THE SIDE PANELS UNTIL EVENLY SPACED THEN ATTACH BACK PANEL by Nes A N d P 9 9
Download Pdf Manuals
Related Search