DreamLine DL-6996-01CL Installation Guide
Contents
1. Fig 29 Fig 30 Rev 1 1 24 Find the desirable height for the Glass shelves 09 and mark the locations on the wall NOTE The Glass shelves can be installed either two in one corner or one in each See Fig 31 for details an Tub Glass Shelves Installation Instruction Fig 31 25 Mark the location for the Shelf brackets 10 according to the measurements in Fig 32 1 Drill the holes using 5 16 drill bit and insert the Wall anchors 06 See Fig 32 for details G 3 o 3 avr Pe 1 IS 5 16 D 2 3 Fig 32 Rev 1 1 20 10 Mount the Glass brackets 10 to the wall using the Countersunk screws ST4 2 x30 NOTE padded set screw of the Glass bracket should be facing down Slide the upper Glass shelf 09 into the Glass brackets and tighten the set screws at the bottom of the brackets Then slide the bottom Glass shelf in place Tighten the set screws as well See Fig 33 and Fig 34 for details Fig 34 Rev 1 1 21 Pr2. Fig 25 Wall Profile gt Side Wall Dn Panel Wall Side Panel Profile Fig 26 Rev 1 1 19 Apply the sealant to the back surface of the Side panel 01 for another side wall installation See Fig 27 for details 20 Repeat Step 18 to install the second Side panel See Fig 28 and Fig 29 for details Fig 27 1 3 2 4 Fig 28 Rev 1 1 21 Fasten tight the Corner covers 04 and the Center cover 05 to secure the Side panels 01 and the Back panels 02 in place See Fig 28 for details Fig 29 Fig 28 Rev 1 1 22 23 Use decorative plugs to cover the screw holes in the Corner covers 04 and the Center cover 05 See Fig 29 for details Apply caulk along the top edge of the panels and along the connection of the bottom edges of the panels with the tub See Fig 30 for details ATTENTION Installation of QWALL Tub is complete If you want to install Glass shelves 09 to your Tub Wall follow to the next step
3. Fig 3 1 D 1 E F lan AN l WY Na F L B C ry D Fig 4 Rev 1 1 5 Attach the Center cover 05 vertically at the center point along the line and mark the drilling holes through the predrilled holes on the Center cover Drill the holes using 5 16 drill bit and insert the Wall Anchors 06 See Fig 6 and Fig 7 for details Fig 5 5 16 Ne A Fig 6 Rev 1 1 6 Attach the Corner cover 04 to the corner of the wall and mark the drilling holes through the predrilled holes on the Corner cover Drill the holes using 05 16 drill bit and insert the Wall Anchors 06 See Fig 8 and Fig 9 for details Fig 7 O5 16 Fig 8 Rev 1 1 Fig 9 7 Determine the position of both Back panels 02 O wo NOTE EOS a Narrow side of the Back panel 5S cannot be trimmed and should face the center of the Back wall b Wide side of the Back panel can be trimmed to the size of the wall X a and should face the corner W241 Place a mark on the wide side of the Back panel with a distance of W 2 1 from the center edge of the Back panel to
4. Rev 1 1 16 Dat Place the marks on the Side panel 01 which is going to the side wall with the fixtures according to the taken measurements in Fig 4 Drill the holes in the Side panel Mind using the proper diameter saw bit or a handheld jig saw See Fig 22 and Fig 23 for details pia Fig 21 Fig 22 Rev 1 1 17 Apply the sealant to the back surface of the Side panel 01 Apply the sealant around the drilled holes and to the whole back side of the Side panel See Fig 24 for details Fig 23 Fig 24 Rev 1 1 18 Slide the edge of the Side panel 01 all the way behind the Corner cover 04 and push the Side panel against the wall Align the top of the Side panel with the Back panel before the sealant sets Apply equal pressure to the whole surface of the Side panel from top to bottom Peel off the adhesive tape on the back side of the Decorative edge molding 03 and attach it to the front edge of the Side panel Apply pressure to the Decorative edge molding from top to bottom See Fig 25 for details NOTICE If you are installing a shower door with the wall profile you can hide the edge of the Side panel 01 behind the wall profile See Fig 26 for details
5. See fig 15 for details Repeat Step 10 to install the Right guide block and the Middle guide block to the Guide rail NOTE If the guide rail has been cut off in Step 2 go to Step 11 the Guide block 13 to the end of the guide rail and mark the drill hole in the Guide rail through the pre drilled hole on the block using 1 8 drill bit Drill the hole and secure the Guide block with the Round head screw ST4 2x16 If the guide rail has been cut off in Step 2 place 1 8 Cover the screw head with Decorative cover 10 See Fig 16 for details a a lt f f y jl Fig 16 Rev 1 1 12 Fasten the Rubber stopper 14 inside the groove of the Wall profile using the Round head screw ST4 2x16 08 See Fig 17 for details 13 Do the final adjustments of the assembled unit in the Wall profiles Drill the holes in the Glass profiles through the predrilled holes on the Wall profile ATTENTION Make sure not to drill the holes throughout only the first layer of the wall profile Secure the Wall profile to the Glass profile using the Round head screw ST4 2x16 08 and cover it with the Decorative cover 10 See Fig 18 for details 1 8 D Fig 18 Rev 1 1
6. 14 Apply the sealant along the profiles and guide rails on the seams between the bottom guide rail and the profiles as well as along the shower base or threshold See Fig 19 for details caulk Fig 19 Product Maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To insure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wire
7. DREAMLINE ream in style Duet Tub Door amp QWALL TUB Kit Tub Door AND SHOWER BACKWALLS KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page STEP 1 Install Shower Backwalls ower Backwalls Installation Instructions STEP 2 Install Shower Door ower Door Installation Instructions Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Kit please visit www BathAuthority com lt BREAMLINE ream in style DUET SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support bathauthority com web page Please carefully read the instructions before installing If you have a
8. damaged or missing please contact DreamLine for replacement Rev 1 1 3 Shower Door Installation 1 Measure the distance between two walls This distance is marked as W See Fig 1 for details 2 The Upper guide rail 01 and the Bottom guide rail 04 has been precut for the installation between the walls with a distance of a 48 If W 48 then it is unnecessary to cut the Guide rails and you can continue to Step 3 If W lt 48 you will need to cut e Upper guide rail 01 from one end The cutting length will be D D 48 W e Bottom guide rail 04 from both ends The cutting length will be D 2 b 60 If W 60 then it is unnecessary to cut the Guide rails and you can continue to Step 3 If W lt 60 you will need to cut e Upper guide rail 01 from one end The cutting length will be D D 60 W e Bottom guide rail 04 from both ends The cutting length will be D 2 See Fig 2 for details Fig 1 o ii l N Fig 2 Rev 1 1 3 Secure Upper guide rail 01 and Bottom guide rail 04 to the Glass profiles 03 with the Flat head screws ST4 2x25 09 See Fig 3 and Fig 4 for details Fig 3 Fig 4 Rev 1 1 4 Push the Wall profiles 02 all the way over the Glass profiles 03 at both side
9. GOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the
10. WER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of r
11. corative edge molding 2pcs 08 Decorative cover 15pcs 04 Corner cover 2pcs 09 Glass shelf 2pcs 05 Wall cover 1pc 10 Shelf bracket 6pcs NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement Rev 1 1 Back Panel Installation Instruction 1 Measure the distance of the back wall of the tub corner to corner W The distance is W See Fig 1 for details Fig 1 W 2 2 Divide the W measurement by 2 S W 2 Place a mark on the back wall e W 2 and draw a vertical line from top to bottom See Fig 2 for details Fig 2 Rev 1 1 3 Measure the side walls from the corner to the front point where the Side panel 01 is going to end This distance is D See Fig 3 for details 4 Verify on which side of your tub wall the fixtures will be installed Place a mark on the side wall NB not the side panel with a distance of 1 one inch from the corner and draw a vertical line from top to bottom Take the exact measurements e from the fixture to the line A B C e from the fixture to the bottom E F See Fig 4 and Fig 5 for details
12. d brushes Rev 1 1 13 QREAMLINE ream In style QWALL TUB TUB ACRYLIC BACK WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page A Please carefully read the instructions before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at 1 866 731 8378 ext 3 or e mail our technical support group at support BathAuthority com For more information on DreamLine Tub Back Wall please visit www BathAuthority com Rev 1 1 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Tub Back Wall Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 3 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 3 business da
13. epair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by either a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FORE
14. ers Attach the Handle brackets 12 to the Glass doors A amp B The handle brackets should face the same direction as the rollers Then secure the Handles 06 to the Handle brackets using Round head screw ST4 2x16 08 Secure the Rollers 11 to the top of 1 2 ps lt NA Fig 9 3 Cover the holes with the Decorative cover provided 9 See Fig 10 for details Fig 10 Rev 1 1 PLEASE NOTE d e On the outside Glass door A the Handle and the Rollers should face out e On the inside Glass door B the Handle and the Rollers should face inside See Fig 11 and Fig 12 for details A Fig 11 9 aps B Fig 12 Rev 1 1 9 One by one suspend both Glass doors onto the Upper guide rail as shown on Fig 13 Tilt the Glass door A a little to make the glass slide into the channel of guide rail Suspend the Glass door B to the guide rail the same way See Fig 13 and Fig 14 for details Fig 13 Fig 14 Rev 1 1 10 11 Slide both Glass Doors to the right Insert the Left guide block 13 into the channel on the left side of the Guide rail and secure it using the Round head screw ST4 2 x 16 08 Cover the screw head with Decorative cover 10
15. ks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such as a photo may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com EAMLINE dream in style TEL 866 731 8378 215 957 1411 FAX 866 227 9245 215 893 1780 WWW BATHAUTHORITY COM For more information on DreamLine Tub Back Wall please visit www BathAuthority com Rev 1 1 24
16. nstall the right Back panel 02 to the right side of the back wall See Fig 16 for details S 2 Fig 15 4 9 q i 6 Fig 16 Rev 1 1 13 Align both Back panels at the top and tighten the screws on the Center cover 05 to secure this assembly in place See Fig 17 and Fig 18 for details Fig 17 Fig 18 Rev 1 1 14 Determine the position of both Side panels 01 NOTE a Narrow side of the Side panel cannot be trimmed and should face the corner of the side wall Wide side of the Side panel can be trimmed to size of your measurements and should face the front of the tub b Place a mark on the wide side of the Side panel with a distance of D 1 from the corner side of the Side panel to the front edge and draw a straight line from top to bottom See Fig 19 for details 1 uo Place the Side panel 01 on a flat piece of plywood or a particle board Cut the side end of the Side panel by making a few deep scratches with a sharp industrial knife using a T Square tool or a handheld jig saw See Fig 20 and Fig 21 for details Fig 19
17. nt in leveling of the door is possible irregular installation surface level or improper angle of side walls will result in serious problems for your installation Please note that some adjustments and drilling might be necessary during the installation process 4 Please NOTE This door has only 2 out of plumb adjustment Make sure your walls are as close to being plumb as possible Tools Required P Drill bit Drill bit Tape Phillips ae oe Caulk Measure Pencil aude vc O 5 16 O 1 8 F g Ke g D oN au l Level Gun i l Hammer Miter saw or Hacksaw Rev 1 1 2 Detailed Diagram of Shower Door Components Packing List 01 Upper guide rail 1pc 08 Round head screw ST4 2x16 16pcs 02 Wall profile 2pcs 09 Round head screw ST4 2x30 18pcs 03 Glass profile 2pcs 10 Decorative cover 10pcs 04 Bottom guide rail 1pc 11 Roller Apcs 05 Glass door 2pcs 12 Handle bracket Apcs 06 Handle 2pcs 13 Guide block left right middle 1 set 07 Wall anchor 8pcs 14 Rubber stopper 6pcs NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are
18. ny questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at 1 866 731 8378 ext 3 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Doors please visit www BathAuthority com Rev 1 1 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 3 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project 3 Please insure that prior to the installation the installation surface is leveled and solid and will be able to support the total weight of the unit Also make sure the walls are at right angles While some adjustme
19. oduct maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface Acrylic cleaning procedure Acrylic should be cleaned with warm water and a clean nonabrasive cloth If desired a mild nonabrasive detergent may also be used Use only light pressure when cleaning Avoid rubbing dirt or grit into the surface Turn the cloth often and replace with a clean cloth frequently Dry by blotting gently with a clean dry cloth DO NOT USE Window cleaning sprays alcohol kitchen abrasive compounds or solvents such as acetone gasoline or thinners Do not use ammonia based cleaning solutions on the acrylic as it will eat into the surface and cause it to damage How do you get scratches out of Acrylic For light scratches use a buffing compound such as a car wax Use the buffer or slightly buff the surface by hands until scratches disappear Rev 1 1 22 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products
20. owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sin
21. purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of DreamLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHO
22. s Make sure the flange of the wall profile faces inside the shower See Fig 5 and Fig 6 for details Fig 5 Fig 6 Rev 1 1 5 Move the finished frame to the designated position and push it against the walls If your top and bottom wall opening measurements are different or if the walls are out of plumb make adjustment by slightly pulling the Wall profiles out of the Glass Profiles Use the level to adjust the frame in the vertical position See Fig 7 for details Using help to hold this frame in the right position mark the drill holes on the wall through the holes on the flange of the Wall Profile Gently set the assembled unit aside drill the holes using 5 16 drill bit and insert the Wall anchors 07 See Fig 8 for details Fig 7 5 16 Fig 8 Rev 1 1 7 8 Apply silicone along the wall profile and around the holes on the wall Also apply silicone under the bottom guide rail Place the shower frame back in to the designated position and secure it to the walls using Round head screws ST4 2 x30 09 See Fig 9 for details the Glass door 05 Mind the position of the roll
23. the wide side of the Back panel and draw a straight line from top to bottom See Fig 10 for details Fig 10 Rev 1 1 8 Place the Back panel 02 on a flat piece of plywood or a particle board Cut the side end of the Back panel by making a few deep scratches with a sharp industrial knife using a T Square tool or a handheld jig saw See Fig 11 and Fig 12 for details Fig 11 wet Fig 12 Rev 1 1 9 Mount the Center cover 05 to the center of the back wall using the Countersunk screws ST4 2x30 07 Do not tighten the screws Leave the Center cover loose on the wall See Fig 13 for details 10 Apply the sealant to the back of the left Back panel 02 See Fig 14 for details Fig 13 Fig 14 Rev 1 1 11 Slide the right edge of the left Back panel 02 all the way behind the Center cover 05 and push the Back panel against the wall You can adjust the position of the Back panel before the sealant sets Apply equal pressure to the whole surface of the Back panel from top to bottom Fasten the Corner cover 04 to the left corner of the back wall using the Countersunk screws ST4 2x30 07 Do not tighten the screws See Fig 15 for details 12 Repeat Step 10 and Step 11 to i
24. ys or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project 3 This acrylic wall system is specially designed to be installed over any solid surface If you are installing the acrylic walls over the existing tiles remove all loose tiles before the installation If you are installing over the existing painted walls take all loose paint off Please note that some cutting and drilling might be necessary during the installation process 4 Make sure to turn off the water supply remove faucet handles or any fixture trims protruding from the wall Clean the surface removing soap film and dirt from all wall surfaces using regular household detergent then wipe it dry Tools Required Tape Drill bit T Square Caulk Measure Pencil Knife 5 16 S D Caulk l Phillips Level Gun ee l Hammer Screwdriver Rev 1 1 2 Detailed Diagram of Tub Back Wall Components 4 1 1 2 3 5 6 3 i i 9 10 Packing List 01 Side panel 2pcs 06 Wall anchor 21pcs 02 Back panel 2pcs 07 Countersunk screw ST4 2x30 21pcs 03 De
Download Pdf Manuals
Related Search