none BT-3060R-037 Installation Guide
Contents
1. gt vy X GTO TAD ONS 3112 3b For existing construction dry fit the bathtub to make sure it fits correctly in the bathtub enclosure framework If necessary modify the framework to achieve the proper bathtub fit 800 325 7008 Installation Procedure Example 1 If the bathtub is to be installed in conjunction with Swan Corporation solid surface wall panels or alternate wall panels ceramic tile the following procedures must be followed 1 After the bathtub installation is complete install 1 2 moisture resistant wall board as shown 2 The Swanstone or alternate bathtub wall material will then be installed over the 1 2 moisture resistant wall board and bathtub flange as shown IMPORTANT NOTICE To prevent possible water wicking affect damage to the wall the wall board must have a 1 2 inch gap above the bathtub flange lip as shown below MOISTURE RESISTANT DRYWALL 1 2 SWANSTONE TUB WALL PANEL OR ALTERNATE TUB WALL PANEL BATHTUB FLANGE 2x4STUD BT 004 The Swan Corporation Swanstone Installation Procedure Example 2 If the bathtub is to be installed in conjunction with a Swan Corporation BA Series Alcove Wall Kit the following procedures must be followed 1 After bathtub installation is complete refer to the alcove wall kit manual for more information o2. 2 If possible fill the bathtub with warm water and mild detergent After draining the bathtub rinse and if necessary use a non abrasive multipurpose cleaner Note To remove especially tough residue or stains use denatured alcohol or mineral spirits If necessary to remove adhesive or glue use products containing Xylene or Toluene AWARNING Solvents Hazard Follow all manufacturer s safety instructions for silicone denatured alcohol and other solvents Solvent vapors are both flammable and hazardous to breathe Silicone vapors may irritate eyes and nose Personal injury can result from improperly handling or use of products containing denatured alcohol mineral spirits or other solvents Always follow the manufacturer s recommendations for the safe use of these products Ventilate any work area before beginning to apply silicone cleaning agents or solvents and solvents used by the installer can be harmful if used in an unventilated room Always work in a well ventilated area CA E RD Fumes Hazard The fumes from the silicone caulk The bathtub installation is now complete DO NOT discard these instructions PLEASE LEAVE THEM WITH THE HOMEOWNER The Swan Corporation Swanstone Care amp Cleaning Care and Cleaning The BT 3060 Bathtub is made of Natural Gloss Composite reinforced polyester The finish is stain and abrasion resistant however the finish requires reasonable care IMPORTAN
3. Application For Sound Deadening or Fireproofing If the bathtub must be elevated above the subfloor for sound deadening or fireproofing excluding above the floor framework the following procedures must be used Note Depending upon wall board application the bathtub enclosure must be framed out accordingly Refer to the Understanding Framework Construction section for more information on wall board installation 1 Refer to the plumbing fixture manufacturers instructions Install any portion of the drain or overflow hardware required prior to bathtub installation Refer to the illustration in the Plumbing section for dimensions 2 Snap the bathtub clips on the bathtub flange and locate as noted in the dimensions illustration 3 Measure and locate 1 x 4 s or 2 x 4 s on the subfloor as noted in the illustration in this section Trial fit the bathtub and make sure there is full contact with the subfloor framework the front bottom edge of the bathtub and the feet on the bottom of the bathtub 1x 4 s or 2x4 s 1x4 s or 2x4 s BT 010 800 325 7008 Installation Procedure 4 Make sure the bathtub is level in both directions If shimming is necessary shim between the 1 x 4 s or 2 x 4 s and the existing subfloor IMPORTANT NOTICE This product is n
4. against a masonry wall First install furring strips or other anchoring materials then secure the bathtub to this framework 800 325 7008 Framework Construction 1 Measure the actual bathtub prior to building or modifying the stud wall framework to determine the exact size required 2 Add 3 8 to the width measurement and at least 3 16 or more to the depth measurement of the bathtub to correctly size the framework opening 3a For new construction build a wood or steel stud framework for the bathtub enclosure Dry fit the bathtub to ensure the recommended dimension exists between the bathtub the side wall framework and the back wall framework IMPORTANT NOTICE If installing a Swan Corporation Alcove Wall Kit in conjunction with the bathtub note that the alcove side panels are designed to extend out past the edge of the bathtub Read the Alcove Wall Kit installation manual and build the framework to the specifications outlined in that publication Note When constructing or modifying stud wall framework make sure to install gang multiple studs to provide support for any required moisture resistant wall board solid surface panel attachment flanges or filler boards etc The framework depth must be at least 3 16 more than the actual depth measurement of the bathtub The illustration below shows a framework depth of 31 1 2 which is greater than the minimum k 4 30 15 6
5. apply to any seams or changes made to the product by professional tradesmen or fabricators The warranty applies only to the original purchaser and installation of these products in commercial applications The Swan Corporation s option to repair or exchange the products under this warranty does not cover any labor or other costs of removal or installation nor shall the Swan Corporation be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product 5 Year Limited Warranty Veritek Bathtubs Save these Installation Instructions for future reference They provide important information on cleaning maintenance and surface repair of the Swanstone Wall Systems and Panels Swan CORPORATION www swanstone com Form BT 3060 06 10
6. drilling the Swanstone product use a dust collection method which prevents dust particles from going into the air Always work in a well ventilated area Always use an OSHA approved dust mask when cutting drilling or sanding Swanstone products 800 325 7008 Safety Guidelines Power Tool Hazard eR To prevent personal injury or possible death always follow the electrical safety recommendations of the power tool s manufacturer Do not use power tools in an unsafe manner Power tools should only be connected to a circuit protected by a ground fault circuit interrupter GFI Shock Hazard AK Never use electric power tools around water condensation or other liquids Electric shock can cause severe burns significant injuries and even death If an extension cord is required always use an OSHA approved extension cord Power cords should only be connected to a circuit protected by a ground fault circuit interrupter GFI Electrical Shock Hazard GZ contac live electrical wiring with power tools or hand tools can cause serious injury or death Make sure all related circuit breakers are turned OFF Test for live circuits or wiring inside any wall where installation of the Swanstone product requires cutting into a wall Electrocution Hazard NA Water and other liquids conduct electric current and can create a short circuit resulting in injury or death Keep all liquids away from electrical cords and power tools D
7. potentially hazardous situation which if not avoided could result in serious injury or death Eye Protection Be sure to use all personal protective equipment to ensure your own safety To avoid eye injury always wear protective glasses with side shields when using power tools Also make sure no one else can be injured by flying particles when using power tools Fire Hazard SQ D Personal injury or death can result from a fire caused by flammable liquids or silicone Cleaners or solvents can be highly explosive resulting in personal injury or even death when not used properly Clean up any flammable substance immediately Sparks or open flames can cause flammable substances to ignite DO NOT smoke while working on or near any flammable substance Solvents Hazard Follow all manufacturer s safety instructions Q77 for silicone and denatured alcohol Alcohol vapors are both flammable and hazardous to breathe Silicone vapors may irritate eyes and nose Personal injury can result from improperly handling or use of products such as denatured alcohol Always follow the manufacturer s recommendations for the safe use of these products Ventilate any work area before beginning to apply silicone cleaning agents or solvents Fumes Hazard The fumes from the silicone and R solvents used by the installer can be harmful if used in an unventilated room Always work in a well ventilated area Dust Hazard When cutting or
8. protect the product from damage by moving it to another room or area until time to install the bathtub O Store the bathtub on a flat surface until the time of installation Do not discard the plastic liner protector from the bathtub until after the installation is complete Do not store the bathtub in a vertical position outside of the original packaging O Please use the model number located on the side of the box or the front of this manual when contacting us with questions concerning the installation of this unit Helpful Hints O Read all instructions carefully BEFORE starting the installation Familiarize yourself with the various parts of the kit O The variety of installations possible for this kit may require procedures other than those shown Ensure that framework construction is correctly sized plumb and square O Keep the plastic liner protector in place for protection of the bathtub during the installation process O Store unused materials away from the work area to prevent accidental damage O If the bathtub is placed over a garage or on an outside wall care must be taken to ensure that the bathtub plumbing is properly insulated from cold temperatures 800 325 7008 General Information Installation Tips Q Measure the actual bathtub before building or modifying the stud wall framework The recommended measurements are 3 8 wider and at least 3 16 deeper than the actual size of the bathtub O Turn o
9. O NOT create a short circuit between a source of electricity and a liquid by being in contact with both simultaneously Grab Bars It is recommended that the bathtub walls be equipped with support grab bars that comply with the most recent edition of ANSI A117 1 requirements Grab bars must be anchored to structural support wall studs behind the Swanstone wall panels Do not rely on the panels only for grab bar support The Swan Corporation Swanstone General Information General Information Followed carefully these installation instructions will result in an easy trouble free installation of your Swanstone BT 3060 Bathtub When installing this bathtub with other Swanstone products such as the BA 3060 Bath Alcove Wall Kit or other wall panel kits read all the installation instructions in each kit before beginning installation Any deviations additions and or deletions from the prescribed installation without prior written approval of our Customer Relations Department will void the warranty covering this product Not following the directions could also result in personal injuries water damage and other damage to floors pipes walls and other portions of your building or home Important Information O If the bathtub is installed in conjunction with a Swanstone BA Series Alcove Wall Kit please read both instruction manuals before proceeding The BA Series Alcove Wall Kits do not require the installation of moisture
10. Swan BT 3060 R Bathtub right side drain CORPORATION BT 3060 L Bathtub left side drain wal O Product Warnings O Safety Guidelines O General Information O Installation Procedure O Special Application O Care amp Cleaning O Warranty Information Form BT 3060 06 10 Register your warranty at www swanstone com The Swanstone Assurance if our product is properly installed and maintained as stated in these instructions it will not leak Remember Safety First IMPORTANT NOTICE The Swan Corporation the makers of the Swanstone products cannot anticipate every possible circumstance that might involve a potential hazard during the installation of our product s The warnings and instructions in this installation guide are therefore not all inclusive If a tool installation procedure or work method that is not specifically recommended by The Swan Corporation is used you must satisfy yourself that it is safe You should also make sure that the Swanstone product s will not be damaged by the methods you choose The Swan Corporation will not be held responsible for water damage of any kind in connection with the installation of one of our Swanstone bath shower panel kits A WARNING To avoid product damage personal injury or even possible death carefully read understand and follow all the instructions in this installation guide before installing this product s Do not use cleaning fluids or oper
11. T NOTICE Because cleaning products change over time always check the manufacturer s instructions to make sure it is compatible DO NOT use abrasive scouring powders cleaners or pads They will dull the finish and void the warranty Day To Day Cleanup Simply wash regularly with warm water use a soft cloth with a mild liquid detergent such as Top Job Ajax Liquid Cleaner Mr Clean All Purpose Cleaner or Glass Plus Remove hard water stains or mineral build up with scale removers such as Lime Away Protect the finish with any fiberglass wax or automotive paste wax Caulking Joints If silicone caulking was applied after installation of the wall panels or tile inspect the caulking joints monthly for damage or any signs of separation from the mating surface Cracks in the caulking will allow water to leak into the surrounding surfaces Reapply caulking to any joint showing signs of wear or cracking Failure to inspect and repair caulking joints will void the warranty 800 325 7008 LIMITED WARRANTY FOR RESIDENTIAL APPLICATIONS If a Swanstone product covered by this warranty is found to be defective in materials or workmanship after inspection by an authorized Swan Corporation representative we will repair or at our option exchange the product for a similar model This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty covers
12. ate power tools unless you read and understand the instructions and warnings in this and all other applicable labels or manuals Proper use of tools and the products described in this guide is your responsibility WARRANTY This product is covered by a Limited Lifetime Warranty Refer to the Warranty section in this manual for complete details Save this manual for future reference Important information on cleaning maintenance and repair is contained within 800 325 7008 3 The Swan Corporation Swanstone Safety Guidelines IMPORTANT NOTICE IMPORTANT NOTICE Indicates that equipment or property damage can result if instructions are not followed Read and Understand the Manual It is the responsibility of any individual who installs or maintains this product to fully understand and follow proper installation and maintenance procedures Be aware of the inherent dangers in the use of power tools when installing this product Read and understand all Warnings Cautions and Important Notices in this manual Work Safely O32 DO NOT proceed if any doubt arises about the correct or safe method of performing anything found in this or other Swanstone manuals The installation of this product can require using power tools Do not use power tools without adequate training If necessary hire or consult a trained professional for expert assistance before continuing Use Proper Tools QS Always use proper tool
13. chniques and use two people to move heavy cartons Use the appropriate lifting devices to move the load Always use two people when lifting heavy or bulky cartons DO NOT attempt to lift objects that are too heavy WHEN CARRYING A HEAVY LOAD GET HELP Slipping Hazard Do not install this product in the presence of water Installing this product without drying all surfaces or in the presence of water could cause you to slip and fall due to wet floors or spilled fluids Personal injury can result from slips or falls Before installation dry all surfaces including the floor with a cloth or paper towel Clean up all water or spilled fluids immediately Tripping Hazard Personal injury can result from tripping over power cords tools or other items DO NOT leave items laying around the work area Personal Protection Be sure to use all personal protective equipment such as sturdy work boots preferably with steel toes gloves and hard hat if necessary to ensure your own safety To prevent possible damage to your hearing always wear ear protection such as earmuffs or earplugs when working around power tools Cutting Hazard The installation of the Swanstone product may require using power tools Keep hands away from the cutting edge of any tool used in the installation of our product Placing fingers in or around the cutting blades could result in serious personal injury 800 325 7008 A WARNING WARNING Indicates a
14. ff the hot and cold water supply during construction O Never install our products directly on any surface that is or may become wet or damp O Ensure all plumbing or electrical work inside the walls or subfloor is finished prior to installation of the bathtub and wall panels O Make sure the drain hole in the subfloor or slab is large enough 6 diameter recommended and aligns with the hole in the bathtub O Verify the overflow drain plumbing will correctly connect to the bathtub O Make sure the subfloor under the bathtub is level in both directions The bathtub must be level when installed Improper installation will void the warranty O The subfloor under the bathtub must be free of dirt film waxes or any other residues 800 325 7008 Disclaimer O The information contained in this Installation Manual is given free of charge It is based upon technical data which we believe to be reliable and is intended for use by persons having knowledge of this technical area at their own discretion and risk Swan assumes no responsibility for results obtained or damage incurred from the use of this material either in whole or in part by the buyer QO This manual will give you basic step by step instructions for the installation of the product that will work in most types of installations If you have an installation application that is not covered in this manual before beginning the installation please call your local Swan di
15. im behind the clips to prevent damage to the bathtub flange when the bathtub clip nails are installed The Swan Corporation Swanstone 5 The bathtub is now ready for a slurry of fast drying cement Quikrete or other product Place up toa 1 2 thick layer of mortar or thinset on the floor This will ensure complete contact and support by the existing subfloor eliminating bathtub flex during normal use IMPORTANT NOTICE This product is not designed for above the floor mounting the base of the bathtub must be fully supported by the subfloor Any application of this type or application other than that covered in this manual will void the warranty 6 Place the bathtub into the framework enclosure and firmly press it into the mortar thinset The bottom front edge of the bathtub should contact the floor surface Level the bathtub in both directions 7 Secure the bathtub clips to the studs with large head roofing nails one nail per clip Allow the mortar thinset to cure for 24 hours Yo 7 BT 009 8 Make sure the protective plastic liner is in the bathtub and or place cardboard or similar scratch resistant material in the bottom of the bathtub to prevent possible damage during further construction 9 Follow all local building codes and manufacturers instructions to install the bathtub enclosure walls and install the plumbing fixtures 800 325 7008 Special
16. itting IMPORTANT NOTICE For remodeling removal of a portion of the subfloor may be necessary Replace the subfloor prior to bathtub installation NEVER install the bathtub over open floor joists The bathtub must be installed on a solid level subfloor 1 Trial fit the bathtub in the stud pocket Measure and verify drain and supply line locations Note Make sure the bathtub fits the framework enclosure properly If necessary make any adjustments to the framework to ensure a correct fit BT 003 STUD FACE gt BATHTUB FLANGE gt gt OVERFLOW 21 2 u S 133 DRAIN 1154 DIA 4 7 SUBFLOOR 2 Remove the bathtub and install the plumbing supply lines as well as waste and overflow lines in accordance with the plumbing manufacturer s installation instructions 800 325 7008 Installation Procedure Bathtub Installation IMPORTANT NOTICE Proper installation requires the bathtub to be set into a bed of mortar type material Quikrete Improper installation will void the warranty 1 Refer to the plumbing fixture manufacturers instructions Install any portion of the drain or overflow hardware required prior to bathtub installation 2 Make sure the protective plastic liner is in the bathtub and or place cardboard or similar scratch resistant material in the bottom of the bathtub to prevent possible damage during further con
17. n installing alcove wall kits 2 Follow those instructions to install any required filler boards and the Swan Corporation Alcove Wall Kit directly to the stud wall framework Multiple Studs Top View B Looking Down 3 4 Filler Board for Shower Door Installation ABS 018c The Swan Corporation Swanstone Example 3 If the bathtub is to be installed in conjunction with existing moisture resistant wall board the following procedures must be followed 1 After the bathtub installation is complete install 1 2 moisture resistant wall board over the existing wall surface as shown 2 The Swanstone or alternate shower wall material will be installed over the new layer of 1 2 moisture resistant wall board and the bathtub flange as shown IMPORTANT NOTICE To prevent possible water wicking affect damage to the wall the second layer of wall board must have a 1 2 inch gap above the bathtub flange lip as shown below MOISTURE RESISTANT DRYWALL 1 2 SWANSTONE TUB WALL PANEL OR ALTERNATE TUB WALL PANEL N N N N KIS w w en Park err 4 EXISTING WALL Fe bat er ae ee oo RS CAPO ERE ws 2x4STUD BT 005 800 325 7008 Plumbing All supply lines to the valves tub spout and shower riser must be located prior to bathtub installation This bathtub accepts a standard 16 adjustable drain and overflow f
18. ot designed for above the floor mounting the base of the bathtub must be fully supported by the subfloor Any application other than that covered in this manual will void the warranty 5 Remove the bathtub Securely attach the 1 x 4 s or 2 x 4 s to the subfloor in the positions determined in Step 3 and Step 4 6 The subfloor is now ready for a slurry of fast drying cement Quikrete or other product This material must completely fill the areas between the 1 x 4 s or 2 x 4 s where the bottom of the bathtub rests This will ensure complete support of the bathtub 7 Place the bathtub into the framework enclosure and firmly press it into the mortar thinset Level the bathtub in both directions 8 Secure the bathtub to the framework studs by attaching the bathtub clips with large head roofing nails one nail per clip 9 Allow the mortar thinset to cure for 24 hours 10 Make sure the protective plastic liner is in the bathtub and or place cardboard or similar scratch resistant material in the bottom of the bathtub to prevent possible damage during further construction 11 Follow all local building codes and manufacturers instructions to install the bathtub enclosure walls and install the plumbing fixtures The Swan Corporation Swanstone Installation Procedure Water Testing 1 Before water testing the bathtub remove any construction materials from the bathtub Also remove the plastic liner protector
19. products installed in accordance with the Swan Corporation s installation instructions used as recommended and not damaged due to misuse abuse or improper installation It does not apply to any seams or changes made to the product by professional tradesmen or fabricators The warranty applies only to the original purchaser and installation of these products in residential applications It does not apply to commercial applications The Swan Corporation s option to repair or exchange the products under this warranty does not cover any labor or other costs of removal or installation nor shall the Swan Corporation be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product Limited Lifetime Warranty Veritek Bathtubs Warranty LIMITED WARRANTY FOR COMMERCIAL APPLICATIONS If a Swanstone product covered by this warranty is found to be defective in materials or workmanship after inspection by an authorized Swan Corporation representative we will repair or at our option exchange the product for a similar model This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty covers only products installed in accordance with the Swan Corporation s installation instructions used as recommended and not damaged due to misuse abuse or improper installation It does not
20. resistant wall board O If the bathtub is installed in conjunction with solid surface wall panels or ceramic tile the stud wall framework must first have the appropriate 1 2 13 mm moisture resistant wall board marine grade plywood or cement board installed Note Install the BA Series Alcove Wall Kit or other appropriate wall board material after installing the BT3060 bathtub Required Tools O Hammer O Sabre saw for cutting drain hole in subfloor O Tape measure O Level OQ Large head roofing nails for bathtub clips O Filler thinset or mortar O Clean paper towels or shop towels Carton Contents The bathtub carton contains one Natural Gloss Composite Bathtub BT 3060 R right side drain or BT 3060 L left side drain and six metal bathtub clips Confirm that all parts of this kit have been included before beginning installation The Swan Corporation Swanstone Unpackaging O This product is shipped to you or your retail center after careful inspection After purchasing the kit carefully unbox and inspect the product for any shipping damage that may have occurred Make sure the bathtub is the correct size and is in good condition Remove the protective plastic tub liner and inspect the bathtub for damage If damage is found report it immediately to the store of purchase Installation of a damaged product will void the warranty O After inspection replace the protective plastic liner During construction
21. s which are in good working condition during the installation of the Swanstone products Using tools other than those listed could adversely affect the integrity of floors pipes walls or this product and could result in water damage or other damage to floors pipes walls or other portions of your building or home Do Not Use Nails To prevent damage to the bathtub and possible water or other damage to floors pipes walls or other portions of your building or home do not nail or screw through the bathtub flange to secure it to the stud wall Bathtub clips included must be used to secure the bathtub in place Refer to the specific instructions in this manual for the proper installation of the bathtub clips av Inspect Before Cutting Make sure no electrical wiring or plumbing is present before cutting into a wall to install any accessories The Swan Corporation Swanstone A CAUTION CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Lifting Hazard 6 According to the National Institute for Occupational Safety and Health the recommended maximum safe lifting weight is 51 pounds with all lifting conditions perfect minimal forward reach steady load close to the body straight back load between knees and shoulders and good grips To avoid personal injury always use these proper lifting te
22. stributor or contact the Swan Corporation directly for additional information about your application O Follow all installation instructions Failure to follow these instructions could result in personal injuries water damage or other damage to floors pipes walls or other portions of your building or home The Swan Corporation Swanstone Installation Procedure Understanding Framework Construction _ __ 60 _____ R O H ame 12 Bathtub Clip BT 001 The BT 3060 Bathtub is approximately 60 wide 30 deep and 16 high It features a 1 1 2 threshold flange and special clips for secure attachment to the framework enclosure IMPORTANT NOTICE Dimensions are approximate sizes only Measure the actual bathtub prior to building the framework to determine the exact size Add 3 8 to the width measurement and at least 3 16 or more to the depth measurement of the bathtub to correctly size the framework opening Note Temporarily remove the protective plastic liner and inspect the bathtub for damage If damage is found immediately report it to the store of purchase Replace the plastic liner during bathtub installation and during construction of the framework Swan Corp cannot anticipate every possible installation situation or condition The variety of installations possible for this bathtub kit may require procedures other than those shown Plan ahead to en
23. struction IMPORTANT NOTICE The bathtub clips must be installed on the bathtub flange prior to the bathtub being inserted into the stud pocket 3 Snap the six bathtub clips onto the 1 1 2 bathtub flange Once installed the clips are designed to slide on the bathtub flange to easily locate clips in lin with the stud locations Note To properly secure the bathtub the flange clips must be attached to solid framework When installing the bathtub over existing moisture resistant wall board example 3 be sure to locate the wall studs and install the flange clips at those points as shown SY YY sv yo ee X X K Ty 7 7 a ee es EEEE 8 Clip Location 6 total The Swan Corporation Swanstone Installation Procedure 4 Trial fit the bathtub Make sure the bathtub is level and all feet on the bathtub are making firm contact with the subfloor Make sure all plumbing connections align properly a It may be necessary to place shims under the bathtub for best overall subfloor contact See Special Application For Sound Deadening Or Fireproofing section in this manual b It may also be necessary to shim between the bathtub flange and the enclosure framework or the existing wall board for best overall bathtub flange clip contact BT 007 IMPORTANT NOTICE Make sure all the bathtub clips contact fit against the studs or existing wall board If a gap exists sh
24. sure that framework construction is correctly sized plumb and square Check local building code before constructing the framework enclosure The Swan Corporation Swanstone The key to a good bathtub installation is proper fit within the stud wall framework Remember these important points to ensure a smooth installation e Completely read and understand this manual and the appropriate bathtub solid surface wall panel installation manual prior to beginning the project e Measure the actual bathtub and use these dimensions to build or modify the stud wall framework to fit Up to a 3 16 gap between the framework and the Swanstone bathtub flange is acceptable Installation Options O The bathtub can be installed with the flange directly against the stud wall framework and 1 2 moisture resistant wall board installed above the bathtub flange O The bathtub can be installed with the flange directly against the stud wall framework and a Swan Corporation BA Series Alcove Wall Kit can be installed directly onto the wall stud framework Refer to the alcove wall kit manual for more information prior to building modifying the framework O The bathtub can be installed with the flange against existing moisture resistant wall board with a second layer of 1 2 moisture resistant wall board added above the bathtub flange Note The bathtub should be set into place prior to wall finishing This unit should not be installed directly
Download Pdf Manuals
Related Search