DreamLine SHDR-4146720-04 Installation Guide
Contents
1. 21 Adjust the Stationary glass 21 position to ensure that when the Glass door 03 is closed there is a gap 1 16 1 8 between the two glass panels To adjust and secure the Stationary glass in place install the Bottom Bracket 27 to the Stationary glass Mark the drilling hole for the bracket Make sure the mark is clear and visible and drill the hole using O1 8 drill bit Use the Round head screws ST4 2X 35 25 to attach the Bottom Bracket to the shower base or the threshold Cover the screw head with Decorative screw cover 26 See Fig 21 for details 22 After final adjustments of the Assembled unit drill the holes in the Glass profiles 2 and 4 through predrilled holes in the Wall profiles 1 and 5 using O 1 8 drill bit NOTE You only need to drill through the first layer of the Glass Profiles Use Round head screws ST4 2x10 14 to secure the Glass profiles inside of the Wall profiles Cover the exposed screw holes with Decorative cover 09 See Fig 22 for details ELEGANCE Rev 4 Ver 2 07 2013 23 Apply silicone sealant between the tray or threshold and the P pivot bracket Also apply silicone between the wall and the wall profiles See Fig 23 and Fig 24 for details Waterproof S Silicon ir Fig 23 NOTE If you need to install the door on the right wall simply exchange the position of the wall profile for g2. Tools Required NA j f Z Mn S CNN Mes NS EN SS bt Drill bit Tape Philips Drill bit Caulk Measure Pencil Screwdriver O 5 16 O 3 16 2 ken We ectric Flat Drill Screwdriver ammer Mallet ELEGANCE Rev 4 Ver 2 07 2013 2 Detailed Diagrams of Shower Door Components Diagram A Diagram B 12 i 2 3 4 5 22 5N 14 25 mS 8 26 E 6 at 17 10 fi 5 80 B OK 11 of 19 S S ps Bottom anti water strip Wall anchor Bolt M4 X 16 with washer Round head screw ST4 2 X 10 Wall profile Flat head screw ST4 2 X 25 Handle Big flat head screw ST4 2 X 40 Pivot assembly upper and bottom 17 Round head socket bolt M6 x 12 Pivot retainer upper and bottom Flat head socket bolt M6 X 12 Decorative cover Hex wrench Anti water strip EE Diagram B Only for door with stationary glass Stationary glass Glass shelf 2pcs 28 Anti Water strip Doo Wall Anchor pcs 30 Shefbracket wthnu Round head screw ST4 2 X35 lpc 31 Shelf bracket without nut NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using parts diagram and part list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damage
3. 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may
4. QREAMLINE ream in style ELEGANCE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page NS G Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Doors please visit www BathAuthority com Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or is missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine
5. also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such a photos may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com TEL 866 731 2244 FAX 866 227 1533 WWW BATHAUTHORITY COM For more information on DreamLine Shower Doors please visit www BathAuthority com
6. door 03 t See Fig 7 for details x b N ears E ANNS VC SNWV we x P J map lt lt AN i W X P NN LLL N Ng Fig 7 8 Open the Glass door 03 See Fig 8 for details Fig 8 ELEGANCE Rev 4 Ver 2 07 2013 9 Close the hole in the bottom Pivot retainer 08 with Flat head socket bolt M6x12 18 or you can attach the Pivot retainer to the Shower base or threshold using Big flat head screw ST4 2 x40 16 Apply silicone sealant over the Screw 16 or Bolt 18 to prevent leakage See Fig 9 for details 10 Push the Anti water strip 10 into the vertical groove of the Glass profile for glass door 02 Attach the Bottom anti water strip 11 onto the glass door You can cut the strips to size by using a knife See Fig 10 for details ELEGANCE Rev 4 Ver 2 07 2013 ATTENTION Steps 11 16 Follow these steps if the width of your door is less than 3734 and you are installing the door without stationary glass and you only need to refer to Diagram A to complete the installation Steps 17 24 Follow these steps if the width of your door is 371A and over and you are installing the door and the stationary glass with glass shelves and you have to use Diagram A and B to complete the installation 11 Push the Glass profile 04 into the groove of the Wall profile 05 and push the Anti water
7. shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR O
8. 40 16 See Fig 3 for details 4 Attach the Pivot assembly 07 to the top and the bottom ends C SS of the Glass profile for glass door 02 with the Flat head DS screws ST4 2x25 15 and M4x16 bolt 13 IN See Fig 4 for details NOTE The Back plate K of the Pivot assembly should face 2 ul inside of your shower Fig 4 ELEGANCE Rev 4 Ver 2 07 2013 6 5 Slide the Glass profile for glass door 02 with Pivot assemblies 07 into the groove CMS NN of the Wall profile for glass door 01 and CR secure the upper Pivot retainer 08 to the upper Pivot assembly 07 with Round head socket bolt M6x12 17 See Fig 5 for details NOTICE The Glass door has 2 cuts for the Pivot assemblies The deeper cut must be on the top 6 Remove the Bolts L and Back plates K from the upper and bottom Pivot assemblies 07 Place the Glass door 03 to the Pivot assemblies attach Back plates K to its position and fasten tight the Bolts Make sure the clear rubber Spacers J are in between the glass and the metal parts Secure tide the Glass door to the Pivot assemblies See Fig 6 for details Fig 6 ELEGANCE Rev 4 Ver 2 07 2013 7 Mount the Handle 06 onto the Glass
9. R MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one
10. ction repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by either a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party
11. d or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference Wall profile for glass door Glass profile for glass door Glass door Glass profile 07 ELEGANCE Rev 4 Ver 2 07 2013 Self Closing Pivot Assembly Parts List E Flat head bolt M4x8 ipo G Bolt M12x10 B Pivotbracket ss dpe H j Sping ip Pivtais tpo j Coe i tp D Waser st to J Spacer pcs E _ End cup washer Je K Back plate F _ Pivot body Bot Regular Pivot Assembly Parts List xO ELEGANCE Rev 4 Ver 2 07 2013 Shower Door Installation 1 Place the Wall profile for glass door 01 on the shower base or the threshold vertically against the finished wall Adjust the Wall profile for glass door vertically using a level Mark the drill holes on the wall through the predrilled holes in the Wall profile for glass door Now drill holes in the wall and insert the Wall anchors 12 See Fig 1 for details Fig 1 2 Push the Pivot retainers 08 into both ends of the Wall profile for glass door 01 See Fig 2 for details Fig 2 ELEGANCE Rev 4 Ver 2 07 2013 3 Runa silicone bead along the holes on the wall Attach the Wall profile for glass door 01 and Pivot retainer 08 to the wall using Big flat head screws ST4 2x
12. if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns 3 If this unit is going to be installed in a new construction install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation 4 Prior to installation ensure that the installation surface is leveled and solid and will be able to support the total weight of the unit Also make sure the walls are at right angles Irregular installation surface level or improper angle of side walls will result in serious problems for your installation Please note that some adjustments and drilling might be necessary during the installation process 5 Please NOTE The doors that are under 373 do not have out of plumb adjustment Make sure your walls are at right angles 6 a If the width of your door is less than 379 4 and you are installing the door without stationary glass you only need to refer to Diagram A with Packing List A b If the width of your door is 37V4 and over and you are installing the door and stationary glass with glass shelves you have to use Diagram A and B with Packing List A and B to complete the installation
13. irectly on the profile NEVER use the metal hammer or hit the profile without the wood bumper Push the Stationary glass with attached Glass profile inside the Wall profile 05 See Fig 17 for details NOTE Please note that the hole in the corner of the Glass panel should be at the bottom farther from the wall Press the Anti Water strip 28 onto the vertical edge of the Stationary glass 21 Align the Stationary glass with the Glass Door 03 and then close the Glass door If needed adjust the position of the Stationary glass to make sure the Anti water strip and the Glass door work well See Fig 18 for details ELEGANCE Rev 4 Ver 2 07 2013 Fig 18 19 Draw a line along the inner edge of the Wall profile 05 on the wall Detach the Wall profile from the Stationary glass 21 and the Glass profile 04 assembly Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile Now drill the holes using O 5 16 drill bit in the wall See Fig 19 for details 20 Insert the Wall anchors 12 into the holes and apply silicone along the Wall profile 05 and around the holes Fasten the Wall profile to the wall with the Big flat head Screw ST4 2x40 16 Push the Stationary glass 21 with the Glass profile 04 back into the Wall profile See Fig 20 for details ELEGANCE Rev 4 Ver 2 07 2013 Fig 19 Fig 20
14. lass door 01 and the wall profile 05 Fig 24 ELEGANCE Rev 4 Ver 2 07 2013 Glass shelves installation NOTE Use parts from Diagram B for the Glass Shelves installation 24 Mark the Glass shelf 22 position on the wall According to the measurements in Fig 25 1 mark the drilling holes on the wall for the Shelf brackets 31 Drill the holes using O 5 16 drill bit and insert the Wall anchors 23 Attach the Shelf brackets 31 to the wall using the Countersunk screw ST4 2x40 32 and attach the Shelf brackets 30 to the Stationary glass 21 Insert the Glass shelves into the Shelf brackets and fasten the screws at the bottom of the brackets See Fig 25 and Fig 26 for details ELEGANCE Rev 4 Ver 2 07 2013 Product Maintenance To ensure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To ensure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe off the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scouring agents as this may scratch the surface Never use bristle brushes or abrasive sponges To ensure a long
15. lasting hardware finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not against across the grain Never use an abrasive sponge or cloth steel wool or wired brushes ELEGANCE Rev 4 Ver 2 07 2013 19 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of DreamLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professio
16. nals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its ele
17. strip 10 into the groove of the Lee Glass profile Close the Glass door 03 Adjust the position of the Glass T I door and position of the Wall profile on the wall to ensure the Glass door has a tight contact with the flange of the Anti water strip from top to bottom E See Fig 11 for details EC Fig 11 ELEGANCE Rev 4 Ver 2 07 2013 10 12 Use a level to ensure that the Glass door 03 and Xe ae a the Wall profile 05 is absolutely vertical A gt ps Draw a line along the vertical edge of the Wall ET A z p profile on the wall Detach the Wall profile from Y the Glass profile 04 Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile ie 5 D Drill the holes using O 5 16 drill bit in the wall See Fig 12 for details ra Z KO Fig 12 13 Insert the Wall anchors 12 into the holes and apply silicone along the Wall profile 05 and around the holes Fasten the Wall profile to the wall with the Big flat head Screw ST4 2x40 16 Push the Glass profile 04 assembly back into the Wall profile See Fig 13 for details ELEGANCE Rev 4 Ver 2 07 2013 11 14 Adjust the width of the Glass door 03 by pulling out the Glass profiles 02 and 04 if it necessary for size of your door Adjust the Glass door using a level and tigh
18. ten in place with the Round head socket bolt M6x12 17 Close the glass door and make sure that there is 1 16 1 8 gap between the glass door and the anti water strip See Fig 14 for details 15 After final adjustments of the Assembled unit drill the holes in the Glass profiles 02 and 04 through predrilled holes in the Wall profiles 01 and 05 using O 1 8 drill bit NOTE You only need to drill through the first layer of the Glass Profiles Use Round head screws ST4 2x10 14 to secure the Glass profiles inside of the Wall profiles Cover the exposed screw holes with Decorative cover 09 See Fig 15 for details ELEGANCE Rev 4 Ver 2 07 2013 Fig 14 16 Apply silicone sealant between the tray or threshold and the pivot bracket Also apply silicone between the wall and the wall profiles See Fig 16 for details ELEGANCE Rev 4 Ver 2 07 2013 f f f fy hi 13 L1 18 Stationary Glass Assembly and Installation NOTE Use parts from Diagram A and B for the Stationary Glass assembly and installation Apply clear silicone along the inner channel of the Glass profile 04 and push the Stationary glass 21 inside the channel NOTE If you have difficulty sliding the Glass profile over the Stationary glass you can slightly tap on the Glass profile with a rubber mallet and a piece of wood Please do not strike d
Download Pdf Manuals
Related Search