Home Decorators Collection 1670610210 Instructions / Assembly
Contents
1. STEP 12 ASSEMBLE BACK PANEL R USE ROUND HEAD SCREW 8 TO ATTACH BACK PANEL R ON THE BACK OF PRE ASSEMBLED UNIT NOTE BEFORE YOU ASSEMBLE THE BACK PANEL PLEASE MAKE SURE THE 2 SIDE PANELS AND DOORS HAVE AN EVEN GAP BETWEEN THEM IF UNEVEN SHIFT THE SIDE PANELS AND ADJUST DOORS UNTIL EVENLY SPACED THEN ATTACH BACK PANEL P 10 102. HOME DECORATORS COLLECTION HDC 16706 MFG TW 19437AB TW 19437AC KENDALL 48 SINGLE VANITY 34 Hx48 Wx22 D ASSEMBLY INSTRUCTIONS Note 1 Before assembly please be sure to work on a soft flat surface to avoid any damage to the finish 2 You need at least 2 people to finish the assembly of this product Made In China P 1 10 BEFORE ASSEMBLY IMPORTANT NOTE READ CAREFULLY BEFORE ASSEMBLY TO PREVENT DAMAGE TO PARTS FOLLOWING INSTRUCTIONS LISTED BELOW IN THE PROPER SEQUENCE AS NUMBERED TO ASSURE FAST EASY AND CORRECT ASSEMBLY ASSEMBLY TOOLS REQUIRED BDA L Screw driver Rubber Mallet Electric drill WOODEN DOWEL INSTALLATION PROCEDURE 1 FILL HOLE 1 4 FULL OF GLUE 0 2 GENTLY TAP DOWEL INTO HOLE WITH RUBBER MALLET OR USE HAND PRESS IN DO NOT USE HAMMER 3 WIPE AWAY EXCESS GLUE Ja HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT LOCK PIN 1 SET INCLUDES C CAM LOCK 1PC BOLT 1PC TOOL NEEDED SCREW DRIVER STEP 1 SCREW BOLT A ONTO PRE SET PLASTIC NUT ON PANEL USE A SCREW DRIVER FOR TIGHTENING ATTENTION DO NOT OVER TIGHTEN THE CAM BOLT A STEP 2 ATTAC
3. 2 8X30mm 1 6X32mm 2 lt 6331288 3 4 33128 5 HINGE SHELF HOLDER ROUND HEAD SCREW CAM BOLT FLAT HEAD SCREW 4 PCS 28 PCS CAM LOCK 4 SETS 24 SETS 111 57 Qa C 0 Ay 65 1111 6 7 3X12mm 8 9 FLAT HEAD SCREW FLAT HEAD SCREW ALLEN KEY GLUE DRAWER LIMIT STOPPER 24 PCS 1 PC 1 PC P 3 10 PARTS LIST BOX 1 TOP PANEL BOTTOM PANEL DRAWER LEFT SIDE PANEL DRAWER RIGHT SIDE PANEL 1 PC 6 PCS 6 PCS C D DRAWER BACK PANEL BACK PANEL 6 PCS 2 PCS B R BOX 2 DRAWER FRONT PANEL DRAWER BOTTOM PANEL ACROSS BAR ACROSS BAR 6 PCS 6 PCS 2 PCS 2 PCS A E F G LEFT SIDE PANEL RIGHT SIDE PANEL LEFT MIDDLE PANEL RIGHT MIDDLE PANEL 1 PC 1 PC 1 PC H J K LEG LEFT DOOR RIGHT DOOR LEG 6 PCS 1 PC 1 PC 1 PC Z Ce N aa LT p Q 5 NOTE THE SURFACE WITH THE STICKER IS THE BACK SIDE P 4 10 STEP 1 ASSEMBLE DRAWER USE SCREW 12 TO ATTACH DRAWER SIDE PANEL amp D AND BACK PANEL TOGETHER INSERT DRAWER BOTTOM PANEL INTO THE SLOTS OF SIDE PANEL amp D USE CAM BOLT amp CAM LOCK 9 TO ASSEMBLE DRAWER FRONT PANEL A AND DRAWER SIDE PANEL C amp D TOGETHER USE ROUND BOLT 10 TO ATTACH KNOB 10 ONTO DRAWER FRONT PANEL A STEP 2 ASSEMBLE DRAWER LIMIT STOPPER 11 e
4. USE FLAT HEAD SCREW 11 TO ATTACH DRAWER LIMIT STOPPER 11 ONTO ACROSS BAR amp G P 5 10 STEP 3 ASSEMBLE SIDE PANEL MIDDLE PANEL 1 AND ACROSS FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 STEP 4 ASSEMBLE SIDE PANEL MIDDLE PANEL J AND ACROSS BAR 0 FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 P 6 10 STEP 5 ASSEMBLE TOP PANEL L FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE ROUND HEAD BOLT FLAT WASHER AND SPRING WASHER 2 TO ASSEMBLE SIDE PANEL H amp K MIDDLE PANEL I amp J AND TOP PANEL L TOGETHER BY ALLEN KEY 13 USE FLAT HEAD SCREW 3 TO ATTACH MAGNET LOCK 3 UNDER TOP PANEL L STEP 6 ASSEMBLE BOTTOM PANEL FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE ROUND HEAD BOLT FLAT WASHER AND SPRING WASHER 2 TO ASSEMBLE BOTTOM PANEL M SIDE PANEL H amp K AND MIDDLE PANEL I amp J TO
5. GETHER P 7 10 STEP 7 ASSEMBLE LEG 8 5 ROTATE LEG N amp S ONTO BOTTOM PANEL M TIGHTLY STEP 8 ASSEMBLE DOOR 0 amp P USE ROUND HEAD BOLT 4 TO ATTACH KNOB 4 ONTO DOOR 0 amp P USE FLAT HEAD SCREW 5 TO ATTACH IRON SLICE 5 ONTO DOOR 0 amp P USE FLAT HEAD SCREW 6 TO ATTACH HINGE 6 ONTO DOOR 0 amp P USE FLAT HEAD SCREW 6 AND HINGE 6 TO ASSEMBLE DOOR 0 amp P ONTO MIDDLE PANEL I amp J P 8 10 STEP 9 PLACE SHELF Q e INSERT SHELF HOLDERS 7 INTO THE HORIZONTAL HOLES INSIDE OF MIDDLE PANEL I amp J THEN PUT SHELF Q ON THEM AS SHOWN gt STEP 10 ASSEMBLE DRAWER LIMIT STOPPER 11 USE FLAT HEAD SCREW 11 TO ATTACH DRAWER LIMIT STOPPER 11 ONTO BOTTOM PANEL M P 9 10 STEP 11 PLACE DRAWER INSERT THE PRE ASSEMBLED DRAWERS INTO THE PRODUCT BODY PROPERLY AS SHOWN
6. H BOTH PANELS MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE HOLE WITH RUBBER MALLET GENTLY CAUTION DO NOT USE HAMMER THEN INSERT CAM LOCK C INTO PRE DRILLED HOLE ON PANEL MAKE SURE THE ARROW ON CAM LOCK C SET IN PANEL POINT TOWARD THE HOLE INTO WHICH THE CAM BOLT A HAS BEEN INSERTED AND INSERTED THE CAM LOCK C TO THE VERY DEPTH OF THE HOLE STEP 3 ROTATE THE CAM LOCK C CLOCKWISE TO SECURE CAM BOLT A BY TIGHTENING WITH A SCREWDRIVER DETAIL STEP PLEASE SEE THE BELOW PICTURE P 2 10 VERTICAL CONNECTION HORIZONTAL CONNECTION 1 a 2 1 2 0 _ 4 3 4 lt 5 THANK YOU FOR PURCHASING THIS QUALITY PRODUCT SURE CHECK ALL PACKING MATERIAL CAREFULLY FOR SMALL PARTS WHICH MAY HAVE CAME LOOSE INSIDE THE CARTON DURING SHIPMENT COUNT ALL PARTS AND MATERIAL HARDWARE COMPARE WITH PARTS LIST TO BE SURE IF ANY PARTS ARE MISSING OR DAMAGED PHONE FAX OR MAIL TO OUR CUSTOMER SERVICE DEPARTMENT FOR EFFICIENT AND SPEEDY SERVICE PLEASE INDICATE THE ALL PARTS ARE PRESENT MODEL NUMBER AND CODE LETTER OF THE PART NEEDED HARDWARE LIST 6 SETS 1 3X12mm 11 4X25mm 12 AS 13 SS a WOOD DOWEL ROUND HEAD BOLT MAGNET LOCK KNOB IRON SLICE 28 PCS FLAT WASHER ROUND HEAD SCREW BOLT FLAT HEAD SCREW SPRING WASHER 1 SET 2 SETS 2 SETS A 16 SETS AS ug 0 FA 1
Download Pdf Manuals
Related Search