Pegasus 4190-48-CP Installation Guide
Contents
1. Rectangular Cat No 7 5 Shower Unit 4190 4192 BARCLAY INSTALLATION INSTRUCTIONS Parts Included Tub Spout 195 S e Gooseneck Riser Pipe 196 R e e Wall Support Bracket w Screws 4195 WS e Shower Head 1003 Tools Needed e Screwdriver Level e 1 4 Drill Bit e Wrench Wood Screws Set Screw 1 Before beginning any work be sure to shut off the water supply 2 Apply teflon tape to ends of both the hot and cold supply nipples Place valve body through holes in tub Thread the large locknuts onto the other ends of the nipples and secure the shower set to the tub 3 Assemble shower head to gooseneck riser pipe 4 Slip the wall bracket over the straight end of the riser pipe Carefully slide the bracket to the appropriate position approximately half way up the rod and tighten the set screw provided 5 Assemble riser pipe to the riser coupling assembly on the spout by tightening the coupling nut After hand tightening fasten securely by using a wrench 6 Secure wall support bracket to the wall using the wood screws provided 7 Turn on water supply NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish Pg 1 4 14 09 P 847 244 1234 www barcl2. ayproducts com Rectangular Cat No me Shower Unit 4190 4192 BARCLAY INSTALLATION INSTRUCTIONS Parts Included e 2 Curtain Frame Sections 1 Wall Tee 1 Ceiling Tee e 1 Wall Support 10 Long 1 Ceiling Support 30 Long 2 Flanges e 4 Wood Screws 10 Set Screws w Heads 1 Headless Set Screw a p at N 1 Connect both halves of the curtain frame 1 using the ceiling tees and wall tees as shown above In order to insure a solid fit the tees fit snugly over the frame tube Install 4 set screws in each tee 2 Remove wall support 6 ceiling support 3 and 2 flanges 4 from the carton Determine the correct length of the support rods as follows A Hold one flange 4 to the wall at desired height from the inside of the tub and centered over the tub Mark the position of the holes to be drilled Fasten the flange to the wall with the wood screws keeping the set screw hole on the top side of the flange B Measure the distance from the center of the wall flange to the ceiling Important From this measurement deduct one 1 2 This will give you the length of the ceiling support rod needed If the ceiling support rod must be shortened cut the non threaded end of the rod to the length desired by using a hacksaw Attach the flange with a set screw to the non threaded end and then attach the ceiling support rod to the ceiling tee 2 3 Screw the wall support rod 6 to the wall tee 5 Pla
3. ce wall support into flange previously mounted on wall see 2A Determine if the wall support rod should be shortened The wall tee 5 should be approximately even with the front rim of the tub when viewed from the side If necessary cut the non threaded end of the support rod 4 Again place the wall support rod 6 into the flange which is attached to the wall The ceiling flange should now be touching the ceiling Mark the location of the holes of the ceiling flange on the ceiling with a pencil Drill holes where marked on the ceiling Remove the ceiling flange from the ceiling support rod 3 Install the ceiling flange using the wood screws If necessary use plastic expansion plugs not provided It is important that the ceiling flange be mounted as securely as possible 5 Insert wall support rod into wall flange and ceiling support rod into flange then tighten the set screws securely Note Wall support tee 5 has additional hole through tee for holding riser pipe of Converto shower if previously purchased The headless set screw is used for attaching the riser pipe to the tee Pg 2 4 14 09 P 847 244 1234 www barclayproducts com
Download Pdf Manuals
Related Search