Coastal Shower Doors NPQFR35.75ORB-C Installation Guide
Contents
1. door to operate properly When satisfied with door operation secure Hinge Post and Strike Post to the Wall Jambs using 638PHPT Adjustment Screws J see ex ploded view sheet 1 12 If Jamb Caps K were purchased install the Jamb Caps K at both the hinge side and the strike side of the door as shown in exploded view sheet 1 Trim the End Caps to required lengths before installing Next Install the Rail End Cap L on to end of Door Rail d3 as shown in exploded view sheet 1 13 With drip wing positioned toward inside of shower enclosure Insert Drip Rail E onto the bottom edge of the Door Assembly D as shown in exploded view sheet 1 and figure 4 Now snug the Drip Rail up to the vertical Vinyl mark the edge of the door glass on the rail and cut off the excess as shown in figure 5 From inside the shower enclosure close the shower door and mark where drip wing needs to be notched for proper closure against door strike see figure 6 Notch the drip rail as required and reposition the Drip Rail on the door and check for fit Once you are satisfied with the Drip Rail fit remove the Drip Rail and run a a bead of clear mildew resistant silicone down the full length the Drip Rail cavity this will insure a secure Drip Rail installation when you reposition it on the glass Reposition the Drip Rail on the glass and press firmly into place 14 Run a bead of clear mildew resistant caulking down the full length of each Wall Jamb outsid2. EMBLY Door Hinge Post Door Hinge Stile designation not used Door Hinge Washer Door Hinge Bushing Door Assembly Screw Door Glazing Vinyl Door Pull Glazing Vinyl Door Pull Door Glass 3 16 thk Vinyls below are used with 1 4 glass c954b c955b Door Glazing Vinyl Door Pull Glazing Vinyl Paragon Frameless Door exploded view left hand hinge shown OPTIONAL JAMP CAP rim excess this side as required typical 2 places r lit Se Q e d tt D SEE DETAIL 1 A THIS PAGE amp D dg dg ED Bee aat iward SEE DETAIL 1 4 ow PS interior af enclosure THIS PAGE drip rail is shown before cuts have been made see figures 4 amp 5 amp amp PART LIST OF MATERIAL KEY PART QTY LETTER NUMBER DESCRIPTION QTY 1 E C 914C DRIP RAIL 1 2 1 F c956c SEAL VINYL Strike Post 2 G 98 45 MAGNET Strike Post 1 H 6 8114PHP INSTALLATION SCREWS 6 l 1329 PLASTIC SCREW ANCHORS 6 1 J 638PHPT ADJUSTMENT SCREWS 6 zis K cp903 JAMB CAP wall jamb 2 2 2 2 Jamb Caps are optional and are ordered separately Fris Paragon Dr w CP931 C914C 03 02 07 1 Measure the base opening along center of shower curb as shown gi in figure 1 then trim Sill A to 1 16 less than measurement obtained I 2 With high lip
3. FHP Door Assembly Screw 2 k2 Plastic Washers 4 d7 c944b Door Glazing Vinyl k3 Sleeve Bushings 2 d8 c945b Door Strike Vinyl 1 k4 Screw Post 2 m d9 931M Door Strike 1 k5 Metal Washers 2 d10 Door Glass 3 16 thk 1 k6 Set Screw 2 L cp903 JAMP CAP wall jamb 2 Vinyls below are used with 1 4 glass d7 c954b Door Glazing Vinyl L d8 c955b Door Strike Vinyl 1 tek A Fris Paragon Dr w ta8 egnw C 914 C 03 02 2007 Jamb Caps are optional and are ordered separately 1 Measure the base opening along center of shower curb as shown in j figure 1 then trim Sill A to 1 16 less than measurement obtained ooo W 2 With high lip toward exterior of enclosure position the Sill at center of shower curb Temporarily tape Sill to shower curb to prevent movement MEASURE BASE OPENING Note For Door Only Installations Trim Wall Jambs B to the same height as the Strike Post C before proceeding otherwise leave Wall Jambs as L_ they are no trimming and continue the installation figure 1 3 Place Wall Jambs B on to ends of Sill A and up against shower walls as shown in figure 2 Plumb the Jambs then pencil mark their installation holes locations on shower walls 3 per jamb Remove Wall Jambs Use a 3 16 drill bit designed to drill through material you are working with to drill 1 1 4 deep installation holes in
4. Paragon Frameless Door w Oval Pull Handle exploded view left hand hinge shown OPTIONAL JAMP CAP rim excess this side as required ypical 2 a S gt O SET SCREWS TO THE INSIDE 2 PLACES miey B ji b y ra ks fs oS dg ko SEE DETAIL 1 A lt F k THIS PAGE amp Qw L O 4 amp Drip wing faces toward interior of enclosure drip rail is shown ds _ before cuts have been 1 4 made see figures 5 amp 6 E DETAIL 1 A amp SNIP SEAL VINYL AS SHOWN P BOTTOM VINYL SHOWN TOP VINYL SIMILAR A T denotes Vinyls used with 3 16 glass PART LIST OF MATERIAL KEY PART KEY PART LETTER NUMBER DESCRIPTION QTY LETTER NUMBER DESCRIPTION QTY A 901 SILL 1 E C914C DRIP RAIL 1 B 903 WALL JAMBS 2 Cc 928 STRIKE POST 1 F c956c SEAL VINYL Strike Post 2 G 98 45 MAGNET Strike Post 1 D DOOR ASSEMBLY H 6 8114PHP INSTALLATION SCREWS 6 d1 920 Door Hinge Post l 1329 PLASTIC SCREW ANCHORS 6 d2 923 Door Hinge Stile 1 J 638PHPT ADJUSTMENT SCREWS 6 d3 designation not used d4 cp148tw Door Hinge Washer 2 K TA8 CGNW OVAL PULL ASSEMBLY d5 cp932 Door Hinge Bushing 2 k1 Handles set 1 d6 812
5. e d9 over Vinyl d8 and tap into place with a rubber mallet until Strike is firmly seated Carefully trim any excess vinyl as required 10 Insert Strike Post C into appropriate Wall Jamb Measure from bottom of Strike Post where it sits on Sill to the bottom of the Door Pull d9 Trim bottom Seal Vinyl F to a 1 4 more than measurement obtained Insert trimmed Seal Vinyl into Strike Post as indicated in exploded view sheet 1 Next insert Magnet Strip G into Strike Post Finally insert remaining Vinyl Seal F and trim top excess as required Snip Seal Vinyl as shown on sheet 1 Detail 1 A 11 Adjust Door Assembly and Strike Post along curb as required Note Bottom of Door Assembly must always remain parallel to Sill in order for door to operate properly When satisfied with door operation secure Hinge Post and Strike Post to the Wall Jambs using 638PHPT Adjustment Screws J see exploded view sheet 1 12 If Jamb Caps L were purchased install the End Caps L at both the hinge side and the strike side of the door as shown in exploded view sheet 1 Trim the End Caps to required lengths before installing 13 Install oval pull Handles K by backing out the two Set Screws k6 and pulling the Handles k1 apart Unscrew the two Screw Posts k4 to disassemble bushings and washers Slip a metal Washer k5 a plastic Washer k2 and Sleeve Bushing k3 onto the Screw Post k4 as shown in Figure 4 Insert it into th
6. e Post is firmly seated top of Hinge Post must be flush with top of glass 7 Insert the Hinge Post d1 into the Hinge Stile d2 as shown in figure 3 Take a minute to check the door rotation is it the correct rotation for your configuration f it is not then make it so When satisfied proceed 8 Insert Hinge Washer d4 and Hinge Bushing d5 into Hinge Stile d2 as shown in figure 3 Rotate Hinge Post d1 out of the way and secure the bushing with one 1 Door Assembly Screw d6 as shown in figure Repeat step for opposite end 9 Pick Door Assembly up and insert its Hinge Jamb d1 into the Wall Jamb from which it is to swing On strike edge of glass center and install Door Pull Vinyl d8 as shown in exploded view Insert Door Pull d9 over Vinyl d8 and tap into place with a rubber mallet until Door Pull is firmly seated 10 Insert Strike Post C into appropriate Wall Jamb Measure from bottom of Strike Post where it sits on Sill to the bottom of the Door Pull d9 Trim bottom Seal Vinyl F to a 1 4 more than measurement obtained Insert trimmed Seal Vinyl into Strike Post as indicated in exploded view Next insert Magnet Strip G into Strike Post Finally insert remaining Vinyl Seal F and trim top excess as required Snip Seal Vinyl as shown on sheet 1 Detail 1 A 11 Adjust Door Assembly and Strike Post along curb as required Note Bottom of Door Assembly must always remain parallel to Sill in order for
7. e glass hole as shown and attach the outside oval pull Handle do not forget to attach plastic washer Hand tighten the screw and repeat step for bottom portion When done carefully tighten down assembly with a screw driver Take inside Handle see explode view sheet 1 and insert it onto the Screw Post heads as shown Finish oval pull Handle installation by tightening down the two set screws 14 With drip wing positioned toward inside of shower enclosure Insert Drip Rail E onto the bottom edge of the Door Assembly D as shown in exploded view sheet 1 and figure 5 Now snug the Drip Rail up to the vertical Vinyl mark the edge of the door glass on the rail and cut off the excess as shown in figure 6 From inside the shower enclosure close the shower door and mark where drip wing needs to be notched for proper closure against door strike see figure 7 Notch the drip rail as required and reposition the Drip Rail on the door and check for fit Once you are satisfied with the Drip Rail fit remove the Drip Rail and run a a bead of clear mildew resistant silicone down the full length the Drip Rail cavity this will insure a secure Drip Rail installation when you reposition it on the glass Reposition the Drip Rail on the glass and press firmly into place 15 Run a bead of clear mildew resistant caulking down the full length of each Wall Jamb outside where the Jambs meet the Walls Now run a bead outside where the Sill meets the curb Follo
8. e where the Jambs meet the Walls Now run a bead outside where the Sill meets the curb Follow caulking manufacturer s instructions before using shower normally 24 hours Installation is now complete Fris Paragon Dr w CP931 C 914 C 03 02 07 Door rota 1 ay figure 3 Door always opens in direction shown above Figure shows installation for a left hand hinged door figure 4 Insert Drip Rail unto bottom edge of glass RAIL UP TO DOOR VERTICAL MARK EDGE OF GLASS ONTO DRIP RAIL AND CUT OFF EXCESS figure 5 Snug Drip Rail up against the vertical Vinyl then cut off the excess as shown in figure AT STRIKE SIDE figure 6 FOR PROPER CLOSURE OF DOOR NOTCH THE DRIP RAIL
9. locations previously marked Insert Plastic Screw Anchors I into holes 4 Reposition Wall Jambs B as before and secure Jambs to walls using the six 6 1 1 2 Installation Screws H provided 3 per jamb 5 Decide from which side your Door Assembly D is to hinge left or right your choice Install Glazing Vinyl d7 onto hinge side of glass as shown in the exploded view Begin glazing at top of glass edge and work down 6 Before installing the Hinge Stile d2 wet the Glazing Vinyl d7 with some diluted liquid soap do not wet the inside of vinyl as it will slip off the glass Insert the Hinge Stile d2 over the Glazing Vinyl and tap into place with a rubber mallet until the Post is firmly seated top of Hinge Post must be flush with top of glass 7 Insert the Hinge Post d1 into the Hinge Stile d2 as shown in figure 3 Take a minute to check the door rotation is it the correct rotation for your configuration If it is not then make it so When satisfied proceed 8 Insert Hinge Washer d4 and Hinge Bushing d5 into Hinge Stile d2 as shown in figure 3 Rotate Hinge Post d1 out of the way and secure the bushing with one 1 Door Assembly Screw d6 as shown in figure Repeat step for opposite end 9 Pick Door Assembly up and insert its Hinge Jamb d1 into the Wall Jamb from which it is to swing On strike edge of glass center and install Door Strike Vinyl d8 as shown in exploded view sheet 1 Insert Door Strik
10. toward exterior of enclosure position Sill at center of shower curb Temporarily tape Sill to shower curb to prevent move ment MEASURE BASE OPENING Note For Door Only Installations Trim Wall Jambs B to the same height as the Strike Post C before proceeding otherwise leave Wall Jambs as they are no trimming and continue the installation figure 1 3 Place Wall Jambs B on to ends of Sill A and up against shower walls as shown in figure 2 Plumb the Jambs then pencil mark their installation holes locations on the shower walls 3 per jamb Remove Wall Jambs Use a 3 16 drill bit designed to drill through material you are working with to drill 1 1 4 deep installation holes in locations previously marked Insert Plastic Screw Anchors I into holes 4 Reposition Wall Jambs B as before and secure Jambs to walls using the six 6 1 1 2 Installation Screws H provided 3 per jamb 5 Decide from which side your Door Assembly D is to hinge left or right your choice Install Glazing Vinyl d7 onto hinge side of glass as shown in the exploded view Begin glazing at top of glass edge and work down 6 Before install Hinge Stile d2 wet the Glazing Vinyl d7 with some diluted liquid soap do not wet the inside of vinyl as it will slip off the glass Insert the Hinge Stile d2 over the Glazing Vinyl and tap into place with a rubber mallet until th
11. w caulking manufacturer s instructions before using shower normally 24 hours Installation is now complete Door rotation j d5 d i ig gt o 4 I l ii do ry U figure 3 Door always opens in direction shown above Figure shows installation for a left hand hinged door ke a k 2 D ky 4 kz GLASS ae figure 4 Install Oval pull Handles as shown above Install outside Handle first as shown then install the inside Handle figure 5 Insert Drip Rail unto bottom edge of glass SNUG DRIP RAIL UP TO DOOR VERTICAL MAR ONTO DRIP RAIL AND CUT OFF EXCESS EDGE OF GLASS figure 6 Snug Drip Rail up against the vertical Vinyl then cut off the excess as shown in figure FOR PROPER CLOSURE OF DOOR NOTCH THE DRIP RAIL AT STRIKE SIDE figure 7 Fris Paragon Dr w ta8 cgnw C 914 C 03 02 2007 se 1 4 DETAIL 1 A SNIP SEAL VINYL AS SHOWN BOTTOM VINYL SHOWN TOP VINYL SIMILAR denotes Vinyls used with 3 16 glass KEY LETTER A B c D d1 d2 d3 d4 d5 d d7 d8 d9 d10 PART NUMBER 901 903 928 920 923 cp148tw cp932 812FHP c944b c945b 931 DESCRIPTION SILL WALL JAMBS STRIKE POST DOOR ASS
Download Pdf Manuals
Related Search