American Standard 2506.152.002 Installation Guide
Contents
1. AND SCREW KIT 2 5mm HEX KEY M962561 YYYOA CARTRIDGE COVER M923320 0070A CARTRIDGE NUT A912740 0070A G 953130 0070A CARTRIDGE Replace the YYY with appropriate finish code L M961619 0070A CHROME 002 MANIFOLD STAINLESS STEEL 075 066070 YYYOA AERATOR A911836 0070A 015025 YYYOA DRAIN COMPLETE 070532 0040A TAILPIECE HOT LINE FOR HELP For tollree information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN MEXICO 01 800 839 12 00 IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2007 M9689442. MOMENTS Instructions VESSEL LAVATORY FITTING 2506 15X with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes Certified to comply with ANSI A112 18 1M M968944 To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended Tools _ y Regular Screwdriver ON Adjustable Wrench 3 Plumbers Putty or Caulking Phillips Screwdriver INSTALL LAVATORY FAUCET CAUTION Turn off hot and cold water supplies before beginning For single hole only NOTE The FAUCET with EXTENSION is used for installation with above counter sinks With the collar of the EXTENSION 1 facing up slide the EXTENSION 1 over the FAUCET SUPPLIES 2 and the MOUNTING STUD 3 The collar of the EXTENSION 1 fits into the groove of the faucet Align the front flats on the faucet and extension FAUCET GROOVE Seat SEAL 4 into groove in EXTENSION 1 base Feed FAUCET SUPPLIES 2 and MOUNTING STUD 3 through mounting hole of deck From b
3. RATOR 3 Ley SERVICE BBTV my Sir ot pos and cold water Turn on valve and allow water supply temperatures to stabilize Move HANDLE to full HOT setting Check water temperature To decrease hot limit temperature setting E Pull out Plug Button 1 loosen Handle Set Screw 2 and remove Handle 3 from Cartridge Stem 5 Remove Cartridge Cover 4 Lift Setting Insert 6 rotate counterclockwise one notch and replace Check water temperature and repeat if necessary Unit is factory set at O full HOT water As the setting number increases the more cold water is supplied in the full HOT handle position Replace Cartridge Cover 4 Align Handle 3 and tighten Set Screw 2 Replace Plug Button 1 EverClean Finish Care Instructions CARTRIDGE HOTTEST Blend control setting O setting insert covers blend control setting number 1 4 COOLEST Blend control setting 4 American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968944 Americam Standard MOMENTS A906099 0070A HANDLE ADAPTER M962562 YYYOA _ EXTENSION KIT A923480 0070A SUPPORT PLATE M961714 0070A MOUNTING KIT VESSEL FITTING MODEL NUMBER M962558 YYYOA HANDLE M962559 0070A BUTTON
4. elow push SUPORT PLATE 7 RETAINING WASHER and GASKET 5 onto MOUNTING STUD 3 Secure Faucet with MOUNTING NUT 6 pulling faucet to front of sink Before final tightening adjust faucet so that it is centered Tighten MOUNTING NUT 6 to complete installation Pe GROOVE IN 3 4 EXTENSION MOUNTING SURFACE 2 MAKE WATER SUPPLY CONNECTIONS E Turn off hot and cold water supplies before beginning m Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply to Hot and right supply to the Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 10 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking Figure A LOOP SUPPLIES IF REQUIRED Apply a bead of PUTTY to underside of DRAIN BODY FLANGE 1 Feed DRAIN BODY 1 down through lavatory Assembly GASKET 2 WASHER 3 and LOCKNUT 4 onto DRAIN BODY 1 Tighten LOCKNUT 4 firmly Assembly TAILPIECE 5 to DRAIN BODY 1 M968944 TEST INSTALLED FAUCET AND CHECK FOR LEAKS With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate HANDLE 1 to flush water lines thoroughly Replace AE
Download Pdf Manuals
Related Search