American Standard 7871.712.002 Installation Guide
Contents
1. AS America Inc 20082. REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 41 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F AO tam REMOVE CAM CAP US60404 Rev 1 3 STOPPER INSTALLATION
3. 733 0070A SPOUT MTG KIT M961724 YYYOA SPOUT KIT 7881 SERIES M953006 0070A TEE amp HOSE KIT M952425 YYYOA DRAIN ASSEMBLY M919660 0020A 6 TAILPIECE NOT INCLUDED WITH FAUCET Replace the YYY with appropriate finish code CHROME 066118 0070A lies ROD PIVOT ROD KIT POLISHED BRASS SATIN PVD CHROME VELVET VELVET BRASS SATIN NICKEL SATIN BRASS r 070847 0070A 5 CLIP M961711 0070A TAILPIECE INSERT 070532 0040A TAILPIECE POP UP DRAIN ASSEMBLY BEFORE 04 06 CHROME BRASS Faucet Pop up Drain MODEL NUMBERS 7871 SERIES 7881 SERIES M962461 YYYOA LIFT ROD amp KNOB 066070 YYYOA AERATOR M961733 0070A SPOUT MTG KIT M961725 YYYOA SPOUT KIT 7871 SERIES I M962544 YYY0A STOPPER ASSEMBLY M964890 0070A CABLE ASSEMBLY M962457 YYYOA FLANGE ASSEMBLY M922872 0070A CAM SEAT INSERT M962430 0070A CAM ASSEMBLY Ge M913207 0070A TAILPIECE INSERT A919661 0020A TAILPIECE M962458 0070A DRAIN MOUNTING KIT HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST y p m IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 1 2 00 US60404 Rev 1 3 Product names listed herein are trademarks of American Standard Inc
4. Fig A q j WHITE FOAM m POP UP KNOB 1 must be fully down Fig B GASKET DRAIN NOT VISIBLE FLANGE US60404 Rev 1 3 F ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 O D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 11 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Thread TEE BODY 4 to SPOUT SHANK 5 E Thread HOSE CONNECTOR 6 GA to VALVE CONNECTIONS 7 7A Connect water supply to VALVE BODIES 1 1 with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet 1 2 PIPE THREAD 3 3 8 0 D _ BULL NOSE RISERS i COMPRESSION FLEXIBLE FERRULE 3 SUPPLIE
5. Installation Instructions 7871 702 7871 712 Spread Lavatory Faucet withthe 7871 722 Speed Connect Drain 7871 732 Congratulations on purchasing your American Standard 7881 702 faucet with Speed Connect drain a feature found only on 7881 712 American Standard faucets 7881 722 7881 732 Certified to comply with ANSI A112 18 1 in Speed Connect Drain Nie A AE e Fewer parts installs in less time e Never needs adjustment e Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the Speed Connect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools 7 nn gt Screwdriver Channel Locks Adjustable Wrench Tubing Cutter INSTALL SPOUT RRSAUUTD inns before beginning Insert SPOUT 4 and CABLE CONNECTOR 192 through center hole making sure the SPOUT ESCUTCHEON 2 and SEAL WASHER 3 are properly seated Assemble RUBBER WASHER 4 BRASS WASHER 5 and LOCKNUT 6 onto SPOUT SHANK 7 from under side of sink Make sure SPOUT 1 is centered in the mounting hole and the slot in the BRASS WASHER 5 faces toward the rear of the sink Tighten LOCKNUT 6 firmly Fig A INSTALL VALVE BODY m Place RUBBER RING 9 into SCUTCHEON 10 E Install LOCKNUT 11 onto VALVE BODY 8 From under side of mounting surface install VALVE BODY 8 through valve mounting holes
6. PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J Ui Loop towarp i REAR OF SINK Re install the Cam Cap making sure the guide teeth are facing Cor outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that
7. S 3 8 COMPRESSION CONNECTION US60404 Rev 1 3 Turn VALVE into OFF position Push ADAPTER 1 into HANDLE BASE 2 in a way that the male square on the ADAPTER 1 fits in the female square of the HANDLE BASE 2 Push HANDLE BASE 2 and ADAPTER 1 onto VALVE STEM 5 Check alignment if not satisfactory aligned E Push out ADAPTER 1 carefully m Turn ADAPTER 1 either 45 or 90 so that male square on ADAPTER 1 catches different female square in HANDLE BASE 2 INSTALL HANDLES Cross mw Turn VALVE into OFF position Push ADAPTER 1 into HANDLE BASE 2 in a way that the male square on the ADAPTER 1 fits in the female square of the HANDLE BASE 2 Push HANDLE BASE 2 and WASHER ADAPTER 1 onto VALVE STEM 5 m PORCELAN f l f HANDLE ONLY Check alignment if not satisfactory 1 aligned m Push out ADAPTER 1 carefully 5 m Turn ADAPTER 1 either 45 or 90 so that male square on ADAPTER 1 catches different female square in HANDLE BASE 2 Secure HANDLE BASE 2 and METAL Secure HANDLE BASE 2 with HANDLE SCREW 3 CROSS 6 or PORCELAIN CROSS 7 with HANDLE SCREW 3 Push INDEX CAP 4 in hole of LEVER BALL 6 Push INDEX CAP 4 in hole of METAL CROSS 6 or TEST INSTALLED FITTING PORCELAIN CROSS 7 With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate both HANDLES 1 to flush
8. Threads of VALVE BODY 8 should extent at least 5 16 of a inch above mounting surface top Fig B Thread ESCUTCHEON 10 onto VALVE BODY 8 until snug against internal stop If necessary adjust LOCKNUT 11 Hand tighten LOCKNUT 11 to secure VALVE BODY 8 Repeat above steps for opposite VALVE BODY 8A 10 _ 9 MOUNTING 5 16 g SURFACE mai 7871 SERIES 2 POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B N S 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE m From under side of SINK Tighten LOCKNUT 41 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK E Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly 6 FLANGE GASKET AND POP UP KNOB m Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible
9. the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD FRONT OF SINK Re install the Cam Cap making sure the guide teeth are facing outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP US60404 Rev 1 3 lt gt 013311 YYYOA INDEX CAP SET 013307 YYYOA METAL CROSS HANDLE X 918428 0070A HANDLE SCREW 042692 0070A PORCELAIN CROSS HANDLE 908501 YYYOA CROSS HANDLE BASE 060353 YYY0A 2 cS PORCELAIN LEVER HANDLE 021470 YYYOA INDEX CAP g 918428 0070A HANDLE SCREW 916503 YYYOA LEVER HANDLE BASE 923002 0070A HANDLE ADAPTER 060354 YYYOA METAL LEVER HANDLE 013312 YYYOA X VALVE ESCUTCHEON KIT 994053 0070A VALVE M906617 0070A ATTACHMENT NUT 4 S TSN 024220 0070A SUPPLY NUT 066116 YYYOA DRAIN STOPPER 066117 YYYOA 2 FLANGE KIT 051376 YYYOA LIFT ROD M953450 YYYOA COMPLETE DRAIN ASSEMBLY 072574 0070A HAMPTON Spread Lavator with M962542 YYYOA LIFT ROD amp KNOB 013306 YYYOA AERATOR M9617193 YYYOA SPOUT ESCUTCHEON KIT M961
10. water lines thoroughly Replace AERATOR 3 1 2 CHECK DRAIN CONNECTIONS E Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Sink If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions Release POP UP KNOB 5 down and check all drain connections and P trap for leaks Tighten if necessary P TRAP 1 3 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT HM To change direction of handle rotation proceed as follows CLEAN WITH CLEAR WATER DRY m Turn valve to OFF position Remove IINDEX 4 and HANDLE SCREW 2 WITH A SOFT COTTON FLANNEL Pull HANDLE 3 off CLOTH Remove ADAPTER 4 Remove SPRING CLIP 5 DO NOT DO NOT CLEAN THE Lift STOP WASHER 6 turn 90 and replace PRODUCT WITH SOAPS ACID Replace oF FING CLE 3 1 Replace ADAPTER 4 HANDLE 2 POLISH ABRASIVES HARSH SCREW 2 and INDEX 1 CLEANERS OR A CLOTH WITH If spout drips operate handles several A COARSE SURFACE times from OFF to ON position Do not force handles turn only 90 US60404 Rev 1 3 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER
Download Pdf Manuals
Related Search