KRAUS KGW-1700ORB-BRCL Instructions / Assembly
Contents
1. MODEL KGW 1700 Product Description and Measurements Installation Instruction Single Lever Washbasin Mixer Thank You Dear Valued Customer Kraus would like to take this opportunity to thank you for purchasing Kraus products It is our sincere hope that you are completely satisfied with your new purchase We welcome any questions or comments you may have and look forward to assisting you in the future Sincerely Kraus customer service department Prior To Installation Steps 1 Unpack your new product and ensure that all the parts are contained in the packaging Keep the product in its original box until you ready to install it 2 Shut off the water supply if replacing a previously installed faucet 3 Observe all plumbing and building codes in your area 4 Itis recommended that installation of the product be done by a professional plumber Waterfall Faucet Installation Please remember to turn off the hot and cold valves prior to installation STEP 1 Check to see that your set contains the following parts The faucet Hot and cold water lines One rubber washer One brass washer Two mounting screws om STEP 2 While holding the faucet facing you locate the two larger openings at the base cana of the faucet STEP 3 The left opening is for the hot water supply line and the right opening is for the cold water supply line STEP 4 Gently screw in the hot and the col2. bber Gasket ip TS 2 Rubber Washer x 43 Metal Washer Flush mck the pipe tl Not aa n m 5 Brass Nut 44 Mounting Screw Please note Do not disassemble the faucet Be sure to flush the water supply lines prior to using the faucet to prevent build up r website at www_kraususa com MODEL KGW 1700 13 faucet width Faucet Opening Make sure the installation holes are in the correct size Sout Prepare the counter top by drilling a 1 diameter faucet hole Install the lavatory as shown in the drawing Connect the main body and water supply pipe with water inlet pipe Usagi amp Maintenance Cleaning amp Maintenance Usage 1 Rinse with warm clean water and blot dry with a clean soft loth only 1 Grab lever and push back to open water flow 2 Never use any detergent polisher scraper or an abrasive 2 Once open tur push to the right to increase cold water loth flow 3 Do not use acid detergent kraususa com
3. d water lines Make sure the waterlines are tightly screwed in place U STEP 5 Insert the waterlines through the faucet opening in the countertop and place the g faucet on the countertop Make sure the faucet is facing forward and is aligned properly STEP 6 From underneath the countertop place the rubber washer first so that it sits on top of the metal washer Be sure to align the openings on the washers with the openings panara on the faucet j Eear STEP 7 Screw in the mounting screws through the washers and into the faucet from LA amun undemeath the countertop STEP 8 Tighten the brass nuts located on the mounting screws until the faucet is held tightly in place STEP 9 Connect the hot and cold water supply lines to the corresponding waters supply valves 100 775 0703 or visit our website at www kraususa com Kr i ap a MODEL KGW 1700 oa Parte List lua 1 Decorative Ring 2Rubber O ring 1 Decorative Ring 1 gt gt s Glass Disc Rubber Ong 1 2 Glass oise aeh Sorew ak amp Lever 6 Rubber O ring 7 Cartridge 1 carvidge 1 Brass Nut 1 5 Brass Nut 6 Rubber O ring 2 a Rubber Gasket 1 Rubber Gasket 0 Base 1 10 Hot and Cold Water Supply Lines 1 3 Base Rubbor Gasket 1 ors Rubber Washer 1 a Metal Washer 1 Mounting Soraw ig j 40 Hot and Cold Water Supply Lines 15 Brass Nut 2 41 Ru
Download Pdf Manuals
Related Search