Leviton 031-VRF01-1LZ Instructions / Assembly
Contents
1. Step 4c LI Matching Remote 3 Way Wiring with Matching Remote w LEDs Application Fan Speed Control Hot Black WH White Line Black Green Ground Yellow Red 120VAC 60Hz e Neutral White NOTE The fan speed contro must be installed in a wall box that has a Load connection The matching remote must be installed in a wal box with a Line Hot connection and a Neutral connection A Neutral wire to the matching remote needs to be added as shown If you are unsure about any part of these instructions consult a qualified electrician NOTE Maximum wire length from fan speed control to all installed remotes cannot exceed 300 ft 90 m WIRING MATCHING REMOTE wall box with Line Hot connection Connect wires per WIRING DIAGRAM as follows Green or bare copper wire in wall box to Green terminal screw Line Hot common wall box wire identified tagged when removing old switch and First Traveler to remote terminal screw marked BK Second Traveler wall box wire from fan speed control to remote terminal screw marked YL RD note wire color This traveler from the remote must go to the fan control Yellow Red lead Line Neutral wall box to remote terminal screw marked WH WIRING FAN SPEED CONTROL wall box with Load connection Connect wires per WIRING DIAGRAM as follows Gr2. If using a non Leviton Programmer Controller a refer to the Programmer Controller instruction sheet for Including a device e If using the VRCPG s Install Checklist feature Menu eton DN Step 8 go directly to Step B A If using a Leviton Z Wave Programmer Controller Cat No VRCPG press the Menu button and scroll down to System Setup Choose Advanced Settings Press the center oe button to select System Setup Menu Press the om center button to select Network B While standing close to the module approx 2 5 ft press the center button to lt Include gt device in the network NOTE Only one device may be included at a time DO NOT put multiple devices into the Inclusion mode at any time C While the Programmer Controller is in the Inclusion mode and the Locator LED is ON on the fan speed control push the push pad to turn ON the fan The Programmer Controller will verify inclusion and the locator LED will turn OFF on the fan speed control If the fan speed control is flashing Amber while in the Inclusion mode the Programmer Controller is still trying to communicate with the fan speed control Wait until the device stops flashing then press the push pad NOTE If the locator LED on the fan speed control turns solid Red while including there has been a communication error Refer to Troubleshooting section D The Primary Programmer Controller will assign a node ID number Name for this module NOTE Th
3. Single Pole One location or 3 Way Multi location Quiet Fan Speed Control Cat No VRFQ1 1L 1 54 vizia rf 1BOVAG 0H LEVI INSTALLATION INSTRUCTIONS WARNINGS AND CAUTIONS DI 000 VRF01 02A X3 WARNINGS AND CAUTIONS e Vizia RF fan speed controls are not compatible with standard 3 way or 4 way switches To be installed and or used in accordance with appropriate electrical codes and regulations They must be used with compatible Vizia or Vizia RF remotes for multi location control If you are unsure about any part of these instructions consult a qualified electrician e Use only one 1 Vizia RF fan speed control in a multi location circuit with up to 9 coordinating remotes without LEDs To avoid overheating and possible damage to this device and other equipment do not install to control a receptacle fluorescent lighting a motor or a or up to 4 matching remotes with LEDs The remote s will turn the fan on at the speed selected at the control transformer operated appliance other than appropriate ceiling fans To reduce risk of fire or electrical shock this control is to be used with ceiling fans that are rated 120VAC total load 1 5 amperes maximum For use on ceiling paddle fans with split capacitor or shaded pole motors only Please refer to manufacturer s instructions or rating label on the motor to confirm type Use with any other types of motors or equipment may cause overheating and or damage to
4. are straight NOTE BK and RD terminals on coordinating remote are unused Tighten both stelliig Rani Goutal h yitsev Ou AMOMmenceMices cut if necessary Remove insulation from each wire in the Conneet wires per WIRING DIAGRAM as follows screws If installing fan speed control in a single device wall box as shown eee eatin iy Gregnilead NOTE Maximum wire length from fan speed control to last remote is 300 ft 90 m application proceed with the INSTALLING ST Green or bare copper wire in wall box to Green terminal screw YOUR FAN SPEED CONTROL section If Strip Gage oan wall box wiro ee aed Load wall box wire identified tagged when removing old switch to First installing fan speed control in a multi device measure bare wire Yellow Red wire should have Red insulation label affixed Traveler note color as above application proceed as follows here or use gage on NOTE If insulating labels not affixed to Yellow Red lead use Second Traveler wal box wire note color a above in terminal serow marked MULTI DEVICE APPLICATION s back of the dimmer electrical tape to cover A LRD Th In multi fan speed control installations there if necessary Remove White insulating label from terminal screw marked WH is no derating necessary Refer to the chart for 5 z z Line Neutral wall box wire to terminal screw marked WH maximum load per fan speed control Proceed to Step 5 Line up tabs and
5. fan speed control in a 3 way application the fan will turn ON at speed set on fan s Fan Speed bar The fan speed can be controlled from either the fan speed control or the remote location Push Pad Default settings Turn ON from OFF position Tap Fan turns ON to preset speed Turn OFF from ON position Tap Fan turns OFF Fan Speed Bar Press Fan Speed Bar right or left to increase or decrease fan speed respectively There are 3 speeds High Medium or Low INCREASE Press the right half of the Fan Speed Bar to increase fan speed DECREASE Press the left half of the Fan Speed Bar to decrease fan speed If you continue to hold the fan will reduce speed to minimum level and then turn OFF NOTE The fan speed can be changed when the fan is off using the Fan Speed Bar In the event of power outage or interruption the fan will reset to the last fan speed when power is restored LED Fan Speed Display Fan Speed Bar Push Pad Locator Light Gently press top Air itch ir Gap Switc of Push Pad On the Fan Speed Control only engage the air gap switch by gently pressing the top of the Push Pad until the bottom lifts completely out of the frame and a click is heard refer to Figure This will cut power to the fixture After servicing is complete press the Push Pad back into place for normal operation Cleaning Clean with a damp cloth DO NOT use chemical cleaners ADVANCED PR
6. turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving Antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio tv technician for help For additional information contact Leviton s Techline at 1 800 824 3005 or visit Leviton s website at www ViziaRFplus com Protected under U S Patent Number 6 388 399 and patents pending and licensed under U S Patents Numbers 5 905 442 and 5 982 103 2008 Leviton Mfg Co Inc DI 000 VRF01 02A X3 LIMITED 5 YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date Leviton s only obligation is to correct such defects by repair or replacement at its option if within such five year period the productis returned prepaid with proof of purchase date and a description of the problem to Leviton Manufacturing Co Inc Att Quality Assurance Department 59 25 Little Neck Parkway Little Neck New York 11362 2591 This warranty excludes and there is disclaimed liability for lab
7. 0 m Changing the color of your device White Black Hot Black Green or bare copper wire in wall box to Green lead Your device may include color options To change color of the face e o Em e Line Hot common wall box wire identified tagged when removing old proceed as follows a pa Green switch to Black lead IMPORTANT For 3 Way applications note that one of the screw First Traveler wall box wire to Red lead note wire color Push in side at terminals from the old switch being removed will usually be a different Yellow nasaia tine Remove Red insulating label from Yellow Red lead tab to release Dee color Black or labeled Common Tag that wire with electrical tape and ned Label 420V AC 60Hz Second Traveler wall box wire to Yellow Red lead note wire color This p gt ats identify as the common Line or Load in both the fan speed control wall traveler from the fan speed control must go to the terminal screw on the box and remote wall box remote marked YL RD e Line Neutral wall box wire to White lead Neel FES e in si Ls Preparing an nnecting wires Neutral White press in sides one d l BAE Preparing and connecting wires WIRING COORDINATING REMOTE Pull off pre cut insulation from fan speed control leads Make Connect wires per WIRING DIAGRAM as follows i A i WIRING FAN SPEED CONTROL bape i Installing Fan Control by itself or with other devi sure that the ends of the wires from the wall box
8. OGRAMMING FEATURES Definition of A Modes A Preset ON Speed Sets the turn on fan speed regardless of the previous speed set Formerly Speed Lock Definition of B Modes B LED Options Sets the time period in seconds the Locator LED and Brightness display will stay on before extinguishing NOTES The device will exit programming mode after 3 minutes of inactivity e Pressing the Push Pad at any time during programming will advance the device to the next programming mode Be ks Program Mode A P nee To enter Program Mode A 7 Press and hold the Push Pad and then the righthalf 1 4 7 of the FAN SPEED Bar for 5 seconds until the LTE Locator LED and leftmost LED LED 1 begins to blink The Locator LED will blink once per second to LED Fan Speed indicate Program Mode A Preset ON Speed To Display 7 change the current Preset ON Speed from HIGH S a7 LED 7 MEDIUM LED 4 LOW LED 1 use the ser FAN SPEED Bar If this feature is not desired press and hold the left half of the FAN SPEED Bar v until no LED is lit default setting By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode A Program Mode B To enter Program Mode B Press and hold the Push Pad and then the left half of the FAN SPEED Bar v for 5 seconds until the Locator LED and rightmost LED LED 7 begins to blink e The Locator LED will blink once per second to indicate Program Mode B LED Options Mo
9. OTE Use check boxes when Steps are completed obstacles and radio dead spots The Scene Capable Quiet Fan Speed Control is WARNING To gt compatible with any Z Wave enabled network regardless of the manufacturer and AVOID FIRE SHOCK Eea For Single Pole Application go to Step 4a 4 n gan albo bs e ane oae displaying the 2 Wave logo OR DEATH TURN HN Ee For 3 Way Coordinating Remote no LEDs Application go to Step 4b CAUTION Remember to exercise good common sense when using the Timer OFF POWER at circuit ba k 2 For 3 Way Matching Remote with LEDs Application go to Step 4c features of your remote especially when scheduling unattended devices There can breaker or fuse and be some unexpected consequences if not used with care For example an empty test that power is off b gt Step 4a Single Pole Wiring Application coffee pot can be remotely turned on If that should happen your coffee pot could before wiring be damaged from overheating If an electric heater is turned on by remote control i while clothing is draped over it a fire could result DO NOT USE the remote for the ge os Fas fl 5 control of high power heating appliances such as portable heaters This device will Identifying your wiring application BK White not control lighting that is used with electronic low voltage and high frequency power most common creer supply transformers nor high pressure discharge lamps HID lighting T
10. de To change the LED Options settings use the FAN SPEED Bar to move the LED to the desired preset setting according to the chart below By tapping the Push Pad this setting will automatically be saved and the device will exit Programming Mode B LED BRIGHTNESS DISPLAY TIMEOUT ctive Turns off 5 seconds after use TROUBLESHOOTING Fan does not turn ON and ON OFF LED does not turn ON Circuit breaker or fuse has tripped Fan has burned out Fan Neutral connection is not wired Confirm that the device is being supplied from a 120V 60Hz AC source ONLY Confirm that unit is programmed properly Repeat TO INSTALL section to verify that it has been included in the Z Wave network Remote does not operate fan Ensure that total wire length does not exceed 300 ft FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by
11. een or bare copper wire in wall box to Green lead Load wall box wire identified tagged when removing old switch to Red lead First Traveler Line Hot to Black lead Remove Red insulating label from Yellow Red lead Second Traveler wall box wire note color as above to Yellow Red lead This traveler from the fan control must go to the terminal screw on the remote marked YL RD Line neutral wall box wire to White lead Proceed to Step 5 Testing your Fan Speed Control prior to mounting in wall box Position all wires to provide room in outlet wall box for device Ensure that the word TOP is facing up on device strap Partially screw in mounting screws in wall box mounting holes Restore power at circuit breaker or fuse Press Push Pad and fan should turn ON If fan does not turn ON press the right half of the Fan Speed Bar until the fan turns ON If fan still does not turn ON refer to the TROUBLESHOOTING section NOTE Dress wires with a bend as shown in diagram in order to relieve stress when mounting device Fan Speed Control Mounting TURN OFF POWER AT CIRCUIT g lt BREAKER OR FUSE Installation may now be completed by tightening mounting screws into wall box Attach wallplate Restore Power Restore power at circuit breaker or fuse Installation is complete Including Scene Capable Fan Speed Control into Z Wave Network Programmer Controller NOTES Cat No VRCPG
12. his includes NOTE If the wiring in your wall box does not resemble any of j i i zl aground mercury vapor sodium vapor and metal halide lamps these configurations consult a qualified electrician i Yellow Red e Line FEATURES Single Pole 3 Way ll l z z 120VAC 60Hz This is a Z Wave controller ON OFF LED and Fan Speed level LED T Kne roy 1 TEEN Scene capable Ease of installation No new wiring 3 Ground ral instruction j 4 Two way communication Compatible with other Z Wave enabled uh below Y Z N a a ay Neutral White RF reliability devices g Neutral ae installations only For single WIRING FAN SPEED CONTROL Yellow Red Coordinating Remote no LEDs Fan Speed Control Black t Black i ut Ground pole installations do not F a i Yellow Red q this insulating label Connect wires per WIRING DIAGRAM as follows Tools needed to install your Fan Speed Control H First Traveler remove Ints insulating 29 NOTE When using the coordinating remote without LEDs the fan speed O ai P note color tity Slotted Phillios Screwdriver Electrical Tape Pliers control can be installed on either the Line or Load side of the 3 way circuit Pencil Cutters i Ruler Second Pe Fan Speed Control NOTE Maximum wire length from fan speed control to all installed remotes i ee note color z cannot exceed 300 ft 9
13. is ID number Name will be stored in the controller library to be used for future reference NOTE You may edit the name of this device at this time E The fan speed control is now installed in the network VRCPG NOTE If a fan speed control rl ce gl has been successfully Included in the network and the user tries to Include it again without first excluding it from the network the module will retain the first node ID it had received and ignore the second Step 9 LI NOTE It is very important to accurately Exclude devices from the network when moving or removing a device from a Z Wave network This ensures that all information has been removed from your Primary Programmer Controller s information table and is not counted on to be a part of the mesh network Center Button NOTE Remote must be in close proximity to fan speed control when including in network Excluding Fan Speed Control from Network A If using a Leviton Z Wave Programmer Controller Cat No VRCPG press the Menu button and scroll down to System Setup Choose Advanced Settings Press the center button to select System Setup Menu Press the center button to select Network B While standing close to the fan speed control press the center button to lt Exclude gt device from the network While the Programmer Controller is in the Exclusion mode and the locator LED is ON on the fan speed control pre
14. or for removal of this product or reinstallation This warranty is void if this product is installed improperly or in an improper environment overloaded misused opened abused or altered in any manner or is not used under normal operating conditions or not in accordance with any labels or instructions There are no other or implied warranties of any kind including merchantability and fitness for a particular purpose but if any implied warranty is required by the applicable jurisdiction the duration of any such implied warranty including merchantability and fitness for a particular purpose is limited to five years Leviton is not liable for incidental indirect special or consequential damages including without limitation damage to or loss of use of any equipment lost sales or profits or delay or failure to perform this warranty obligation The remedies provided herein are the exclusive remedies under this warranty whether based on contract tort or otherwise
15. ss the push pad on the fan speed control The Programmer Controller will verify Exclusion and the locator LED will turn OFF on the fan speed control If the fan speed control is flashing Amber while in the Exlusion mode the Programmer Controller is still trying to communicate with the fan speed control Wait until the device stops flashing then press the push pad Factory Default If your fan speed control is not responding or you are unable to control it after you have tried to Include Exclude it multiple times it may be necessary to reset the fan speed control to its original factory settings To accomplish this proceed as follows On the fan speed control engage the air gap switch refer to Operation section and wait 5 seconds Press push pad back into frame and hold push pad until the locator LED turns Amber and then flashes Red The fan speed control is now reset Once the fan speed control is reset it will be necessary to Re Include it to a network before it can be used CAUTION SETTING A DEVICE TO A FACTORY DEFAULT DOES NOT EXCLUDE THAT DEVICE FROM A NETWORK THE EXCLUSION PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE FROM THE PRIMARY CONTROLLER S INFORMATION TABLE FAILURE TO DO SO MAY RESULT IN A SYSTEM THAT IS SLOW TO RESPOND OR MAY FAIL TO RESPOND TO SOME DEVICES OPERATION NOTE The locator light will illuminate when the load is in the OFF position to facilitate access in the dark NOTE If using the
16. the motors or equipment Recommended minimum wall box depth is 2 1 2 Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft 90 m Disconnect power at circuit breaker or fuse when servicing installing or removing fixture Use this device only with copper or copper clad wire With aluminum wire use only devices marked CO ALR or CU AL INTRODUCTION MAXIMUM LOAD PER FAN SPEED CONTROL FOR MULTI DEVICE APPLICATION For non standard wiring applications refer SE 3 Way Wiring with Coordinating Remote to Wire Nut and Connector Size Chart ication Leviton s Vizia RF components are designed to communicate with each other via Cat No Single Two Devices More than 2 Devices one ppiconon Radio Frequency RF to provide remote control of your lighting Using RF technology VRFO1 WIRE CONNECTOR OF COND COMBINATION CHART Coordinating Remote Fan Speed Control allows Leviton to provide the greatest signal integrity possible Each module in 1 12 w 1 to 3 14 16 or 18 Leviton s Vizia RF component line is a Z Wave enabled device In a Z Wave INSTALLING YOUR FAN SPEED CONTROL 2 12 w 1 or 2 16 or 18 network each device is designed to act as a router These routers will re transmit 1 14w 1 to 4 16 or 18 the RF signal from one device to another until the intended device is reached This 1 2 14 w 1to 3 16 or 18 ensures that the signal is received by its intended device by routing the signal around N
Download Pdf Manuals
Related Search