Illumine CLI-EMM030857 Installation Guide
Contents
1. the breaker panel or fuse box securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box Figure 10 Carefully lift the fan and seat the hanger ball downrod assembly onto the hanger bracket that was just attached to the outlet box Figure 11 Rotate the entire fan assembly until the ball groove engages the anti rotation tab Be sure the groove in the ball engaged the anti rotation tad on the hanger bracket Figure 10 44 WARNING Hanger bracket must seat firmly against outlet box If the outlet box Is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall Aa WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard To avoid possible fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket CEILING T PEN rms EEE ee AT ae Figure 9 NOTE CEILING COVER OMITTED FOR CLARITY TWO SCREWS SUPPLIED WITH OUTLET 80X q A Na BRAGKET TAB Figure 10 NOTE CEILING COVER SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY HANGER BRAGKET HANGER BALL DOWNROD ASSEMBLY P 1 1 4 THREADED STUD 2 Figure 11 U L Model No CF755 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience have your fan instalied by a l2. to color before they CONNECTOR MOTOR CONNECTOR can be engaged Make sure the connector latch VJ no coges propSNy MOUNTING SCREW ae Remove the three switch housing mounting screws aS Ray lt lt Figure 5 from the switch housing plate Position eg er ee ihe switch housing assembly on the switch Figures housing plate and align the holes in the switch housing assembly with the holes in the plate Secure the switch housing assembly by installing the three screws Figure 6 SWITCH HOUSING 4m WARNING ASSEMBLY To avoid possible fire or shock do not pinch wires between the switch cup assembly and the switch cup piate U L Model No CF755 How to Put Your Ceiling Fan Together continued 8 Turn fan assembly upside down in preparation for mounting fan blade assemblies M5 x 6 WASHER HEAD BLADE SCREW 3 9 Mount blade flanges to fan blades using three M5 x BLADE WASHER 3 6 washer head blade screws and three blade washers Figure 7 NOTE Take care not to scratch fan housing when Installing blades NOTE Remove and discard the four shipping spacers and screws from the motor hub Figure 7 10 Loosely attach one blade assembly to the motor hub using two M6 x 14 captive screws with lockwashers Make sure the screws are NOT tightened Figure 8 Repeat this procedure for other four blade assemblies 44 WARNING To reduce the risk of personal injury do not bend the blade flange when installi
3. READ AND SAVE THESE INSTRUCTIONS Ceiling Fan Owner s Manual ae Net Weight 18 0 Lbs ENERGY STAR Part No F40BP73170002 Form No BP7317 2 U L Model No CF755 A WARNING WARNING To avoid flre shock and serious personal injury follow these instructions Safety Instructions Read your owner s manual carefully and keep it for future reference 2 Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from belng switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Be careful of the fan and blades when cleaning palnting or working near the fan Always turn off the power to the ceiling fan before servicing Do not put anything into the fan blades while they are turning Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades All wiring must be in accordance with the Natlonal Electrical Codes ANSI NFPA 70 2011 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licen
4. assembly from the protective plastic bag Place the fan assembly into the upper This product is designed to use only those parts foam pad with the bottom of the motor facing up supplied with this product and or any accessories The upper foam pad serves as a holder for the fan designated specifically for use with thls product by during the first stages of assembl Emerson Electric Co Substitution of parts or g g y accessories not designated for use with thls product by Emerson Electric Co could result in personal injury or property damage 1 Check to see that you have received the following parts NOTE If you are uncertain of part description ASSEMBLY refer to exploded view illustration er Fan motor assembly One switch housing assembly HANGER BALL Five fan blades DOWNROD P One ceiling cover i SWITOH CU pene Five blade flanges Sy HANGER One hanger ball downrod assembly One hanger bracket One coupling cover One loose parts bag containing 1 Sixteen M5 x 6 washer head blade screws 2 Sixteen blade washers One M6 x 14 captive screw with lockwasher One wood pendant One coupling Three wire connectors Two threaded studs Two knurled knobs Two lockwashers One clevis pin One hairpin clip 7a m oad FD CEILING COVER ea O0O02M NDOR l U L Modei No CF755 How to Put Your Ceiling Fan Together 1 Remove the hanger ball by loosening the set
5. e the coupling cover on the downrod until it rests on the motor housing Place the ceiling cover over the downrod Be sure that the ceiling cover and the coupling cover are both oriented correctly Figure 3 DOWNROD Figure 1 Figure 2 Figure 3 MOTOR COUPLING MOTOR COUPLING U L Model No CF755 How to Put Your Ceiling Fan Together continued Reinstall the hanger ball Figure 4 on the downrod as follows Route the three 80 motor leads through the hanger ball Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball A loose setscrew could create fan wobble 44 WARNING It is critical that the pin In the hanger ball is properly Installed and the setscrew securely tightened Figure 4 Failure to verify that the pin and setscrew are properly Installed could result In the fan falllng 5 The fan comes with blue black and white leads that are 80 long Before installing fan measure up approximately 6 to 9 inches above top of hanger ball downrod assembly Cut off excess leads and strip back insulation 1 2 inch from end of leads 6 Engage the connector of the switch housing assembly with the motor connector Figure 5 The two connectors are keyed and color coded and Sia N SWITCH HOUSING 0 must be mated correctly color
6. icensed electrician Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be In accordance with National and Local codes and the celllng fan must be properly grounded as a precaution against possible electrical shock 4 WARNING To avold possible electrical shock be sure electricity is turned off at the main fuse box before wiring NOTE If you are not sure if the outlet box is grounded contact a licensed electrician for advice as It must be grounded for safe operation NOTE If you are using an Emerson Light Fixture with your fan see Light Fixture Owner s Manual for wiring 2 Securely connect the fan motor white wire to the supply white neutral wire using wire connector supplied Figure 12 Securely connect the fan motor black wire and blue wire to the supply black hot wire using wire connector supplied Figure 12 After connections have been made turn leads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box 4 WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result 3 Screw the two threaded s
7. ing the fan Do not insert foreign objects in between rotating fan blades WARNING To reduce the risk of electrical shock this fan must be Installed with an isolating wall control switch i DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use U L Model No CF755 This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder One 1 4 blade screwdriver One wire stripper Three wire connectors supplied MATERIALS Wiring outlet box and box connectors must be of type required by the local code The minimum wire would be a 3 conductor 2 wire with ground of the Up to 50 ft 50 100 ft WARNING Before assembly your ceiling fan refer to sectlon on proper method of wirlng your fan page 8 If you feel you do not have enough wiring knowledge or experlence have your fan installed by a licensed electrician following size Unpacking Instructions NOTE Place the parts from the loose parts bags in a small container to keep them from being lost Do not install or use fan if any part is damaged or If any parts are missing contact your local missing Call Toll Free retailer or catalog outlet for replacement before 1 800 654 3545 proceeding 2 Remove the fan
8. ng the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects In between rotating fan blades 11 The blade flanges have an interlocking feature that must be fully engaged before tightening the screw Make sure all the flanges are properly engaged and then tighten the flange screws If one of the flanges does not seat properly on the motor hub loosen the adjacent flange screws re engage and reseat the flanges then tighten the screws again You have now completed the assembly of your new ceiling fan You can now proceed with hanging and wiring your fan Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit a WARNING The outlet box must be securely anchored and Turning off wall switch is not sufficient To avoid capable of withstanding a load of at least 50 pounds possible electrical shock be sure electricity Is turned off at the main fuse box before wiring All wiring must be In accordance with National and A WARNING Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical To reduce the risk of fire electrical shock or shock personal Injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes da WARNING commonly used for support of light flxtures are not To avold fire or shock follow all wirin r g In
9. screw in the hanger ball until the ball falls freely down the downrod Figure 1 Remove the pin from the downrod then remove the hanger ball Retain the pin and hanger ball for reinstallation in Step 4 Separate untwist and unkink the three 80 motor leads Route the motor lead wires through the downrod Remove the upper setscrew from the motor coupling Align the clevis pin holes in the downrod with the holes in tne motor coupling Install the clevis pin and secure with the hairpin clip Figure 2 The clevis pin must go through the holes in the motor coupling and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin The hairpin clip must be properly installed to prevent the clevis pin from working loose Pull on the downrod to make sure the clevis pin is properly installed Reinstall the upper setscrew in the motor coupling Check that the lower setscrew is tightened securely Figure 2 NOTE The setscrews must be properly installed as described above or fan wobble could result 44 WARNING It is critical that the clevis pin In the motor coupling is properly installed and the setscrews securely tightened Fallure to verlfy that the pin and setscrews are properly Installed could result In the fan falling 3 Make sure the grommet is properly installed in the coupling cover then slid
10. sed electrician The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of ight fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot celling The fan must be mounted with the fan blades at least 7 feet from the floor to prevent acc contact with the fan blades Follow the recommended instructions for the proper method of wirlng your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician WARNING To avold fire shock or injury do not use an Emerson or any other brand of control not specifically approved for this fan WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or clean
11. structions acceptable for fan support and may need to be carefully Any electrical work not described in these replaced Consult a qualified electriclan If instructions should be done or approved by a in doubt licensed electrician If your fan is to replace an existing ceiling light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture U L Model No CF755 How to Hang Your Ceiling Fan WARNING Turning off wall switch is not sufficlent To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be In accordance with National and Local codes and the celling fan must be properly grounded as a precaution against possible electrical shock WARNING The fan must be hung with at least 7 of clearance from floor to blades Figure 9 WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 Ibs Use only a ULL outlet box listed as Acceptable for Fan Support WARNING To reduce the risk of fire electrical shock or personal Injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplled with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if In doubt With the branch circuit electricity turned off at
12. tuds supplied into the tapped holes in the hanger bracket 4 Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover Figure 13 5 Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs supplied Figure 13 Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod Your fan is now wired to be turned on and off from the fan switch BLACK AND BLUE GROUND FANWIRES WIRE WHITE SUPPLY NEUTRAL ENN PS BY 3 WHITE FAN ANGER BRACKET WIRE GREEN WIRE BLACK SUPPLY GROUND FROM HOT HANGER BALL NOTE CEILING COVER OMITTED FOR CLARITY Figure 12 po GEILING GOVER THREADED STUD LOCKWASHERS 2 KNURLED KNOB Figura 13 To avoid possible fire or shock make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling 6 Cut the 3 speed switch pull chain to a desired length optional Connect the wood pendant supplied to the 3 speed switch pull chain by sliding the wooden pendant small hole first onto the pull chain Attach the chain coupling to the end of the chain and allow the wooden pendant to fall down over the coupling U L Model No CF755
Download Pdf Manuals
Related Search