Home

Illumine CLI-ONF120ORB Instructions / Assembly

image

Contents

1. 2 Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing 3 Do not put anything Into the fan blades while they are turning 4 Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation 1 To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 2014 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical Installation should be made or approved by a licensed electrician DATE CODE 3 The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support of 22 7 kg 50 Ibs or less and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt 4 The downrod furnlshed with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling 5 The fan must be mounted with the fan blades
2. blades are in place Noise and fan damage could result dx WARNING To avoid possible fire or shock make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling turn until studs protrude through the holes in the ceiling cover Figure 10 5 Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs supplied Figure 10 Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod Your fan ts now wired to be turned on and off from the fan switch 6 Cut the 3 speed switch pull chain to a desired length optional Connect ihe wood pendant supplied to the 3 speed switch pull chain by sliding the wooden pendant small hole first onto the pull chain Attach the chain coupler to the end of the chain and allow the wooden pendant to fall down over the coupling U L Model No 52 ANT 6 Using Your Ceiling Fan Restore electrical power to the outlet box by turning the electricity on at the main fuse box Check the operation of the fan by gently pulling on the pull chain switch All fans are shipped from the factory with the reversing switch positioned down to circulate air downward If airflow is desired in opposite direction tum your fan OFF and wait for the blades to stop turning then sli
3. holder for the fan during the first stages of assembly OOMNOTAD N _ This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly Ins Hed Wite L Wire Size A W G One Phillips head screwdriver One stepladder i fi 42 One 5 16 blade screwdriver One wire stripper 4a WARNING Materials Before assembling your ceiling fan refer to section on 8 roper method of wiring your fan page 7 If you feel Wiring outlet box and box connectors must be of type cou do not have sniouali a or required by the local code The minimum wire would be experience have your fan installed by a licensed a 3 conductor 2 wire with ground of following size electriclan 3 U L Model No 52 ANT 2 Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit A WARNING To reduce the risk of fire electric shock or personal injury mount fan to cutlet box marked Acceptable for Fan Support of 22 7 kg 50 Ibs or less and use screws supplied wlth outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds If your fan is to replace an existing ceiling li
4. properly installed to prevent the clevis SETSCREWS pin from working loose Pull on the hanger ball to make sure the clevis pin is properly installed da WARNING Figure 1 It is critical that the clevis pin in the motor coupling Is properly installed and the setscrews securely tightened Failure to verify that the pin and setscrews are properly installed could result in the fan falling U L Model No 52 ANT 3 Ceiling Fan Assembly continued 4 While pulling up on the hanger ball securely tighten the two setscrews in the motor coupling Figure 1 NOTE The setscrew must be properly installed as described above or fan wobble could result 5 The fan comes with blue black and white leads that are 42 inches long Before installing the fan measure up approximately 6 to 9 inches above top of hanger ball downrod assembly Cut off excess leads and strip back insulation 1 2 inch from end of leads Mount the biade flanges to fan blades using three M5 x 6 washer head blade screws per blade Figure 2 4 WARNING To reduce the risk of personal injury do not bend the blade flange when Installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades NOTE Take care not to scratch fan housing when installing blades NOTE Remove and discard the four shipping spacers and screws from the motor hub 7 Turn the fan assembly upside down in preparation for m
5. READ AND SAVE THESE INSTRUCTIONS E IA raro ee SS See E zE Pia 52 Ceiling Fan Owner s Manual Net Weight 16 5 Lbs on Part No F40BP72240009 Form No BP7224 9 Revislon 131101 U L Model No 52 ANT Table of Contents Section Page Sectlon Page Safety Instructions iii i 2 7 Maintenance soi area aa 8 1 Unpacking Instructions 3 8 Energy Efficient Use of Ceiling Fans 8 2 Electrical Requirements 0 cece eee 4 9 ACCOSSONOB x pit OA ETEK GAD ORCAS RESO 9 3 Ceiling Fan Assembly cerro 4 5 10 Trouble Shooting 1 scuri is edesove ea tietas 9 4 How to Hang Your Ceiling Fan 6 11 R p ir PANS rare 10 11 5 How to Wire Your Ceiling Fan 0c cece ees 7 Ceiling Fan Limited Warranty 12 6 Using Your Ceiling Fan insita ehe 8 READ AND SAVE THESE INSTRUCTIONS Safety Instructions 4x WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Use this unit only in a manner intended by the manufacturer If you have questions contact the manufacturer Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 1 Read your owner s manual carefully and keep it for future reference
6. at least 7 feet from the floor to prevent accidental contact with the fan blades 6 Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician WARNING To reduce the risk of electrical shock this fan must be installed with an isolating wall control switch WARNING To avold fire shock or injury do not use an Emerson or any other brand of control not specifically approved for this fan WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades NOTE All setscrews must be checked and re tightened where necessary before installation The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use U L Model No 52 ANT 1 Unpacking Instructions NOTE Place the parts from the loose parts bags in 4 WARNING a small container to keep th
7. ation Securely connect wires with wire connectors supplied Figure 9 NOTE If you are using an Emerson Light Fixture with your fan see Light Fixture Owner s Manual for wiring NOTE CEILING COVER OMITTED FOR CLARITY Figure 9 CEILING COVER a WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage THREADED STUD LOGKWASHER KNURLED KNOB Figure 10 3 Screw the two threaded studs supplied into the tapped holes in the hanger bracket 2 Securely connect the fan motor white wire to the 4 Lift the ceiling cover up to the threaded studs and supply white neutral wire using wire connector supplied Figure 9 Securely connect the fan motor black wire and blue wire to the supply black hot wire using wire connector supplied Figure 9 After connections have been made turn leads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box A WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until
8. attached to the outlet box Figure 8 Be sure the groove in the ball is lined up with tab on the hanger bracket Figure 7 d WARNING Fallure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard dx WARNING To avoid possible fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket CEILING 7 7 AT LEAST r NOTE CEILING COVER OMITTED FOR CLARITY TWO SCREWS SUPPLIED WITH OUTLET BOX Figure 7 NOTE CEILING COVER SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY HANGER BRACKET HANGER BALL DOWNROD ASSEMBLY Figure 8 U L Model No 52 ANT 5 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical BLACK AND BLUE wiring knowledge or experience have your fan erounp FAN WIRES Installed by a licensed electrician WIRE Hine A WARNING To avoid possible electrical shock be sure electricity is turned off at the maln fuse box before wiring NOTE If you are not sure if the outlet box is grounded contact a Ilcensed electrician for advice as it must be grounded for safe operation WHITE SUPPLY NEUTRAL GREEN WIRE a FROM ANGER BRACKET GREEN WIRE eae FROM ANGER BALL Di SUPPLY Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply this may be a bare wire or wire with green colored insul
9. de the reversing switch to the up position and turn fan on again The fan blades will turn in the opposite direction and reverse the airflow Your fan model is equipped with a 4 position 3 speed pull chain switch The operating sequence is as follows Three Speed fst Pull HIGH 2nd Pull Medium 3rd Pull Low 4th Pull OFF Reverse Switch Information Season Rotation Direction Switch Position Summer Counter Clockwise Down Winter Clockwise Up _ Energy Efficient Use of Ceiling Fans Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan Here are a few tips to ensure quality and product performance Choosing the Appropriate Mounting Location Ceiling fans should be installed or mounted in the middle of the room and at least 7 feet above the floor and 18 inches from the walls If ceiling height allows install the fan 8 9 feet above the floor for optimal airflow Consult your Emerson Retailer for optional mounting accessories Using the Ceiling Fan Year Round In the summer use the ceiling fan in the counter clockwise direction The airflow produced by the ceiling fan creates a wind chill effect making you feel cooler Select a fan speed that provides a comfortable breeze lower speeds consume less energy In the winter reverse the motor and operate the ceiling fan at low speed in the clockwise direction This produces a gentle updraft which f
10. em from being lost If Do not install or use fan if any part is damaged or any parts are missing contact your local retailer or missing catalog outlet for replacement before proceeding 2 Remove the fan assembly from the protective piastic l bag Place the fan assembly into the upper foam pad d WARNING with the top of the motor facing up This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury a PARTS or property damage FAN MOTOR ASSEMBLY 1 Check to see that you have received the following l 2 Xx LEE parts Ns Z HANGER BALL NOTE If you are uncertain of part description refer 3 k x A I nae to exploded view illustration di Fan motor assembly A i HANGER One switch housing assembly ssi TI gres Five fan blades SS WS One ceiling cover U A i Five blade flanges SWITCH CUP One hanger ball downrod assembly COVER COVER ASSEMBLY One hanger bracket One loose parts bag containing 1 Sixteen M5 x 6 washer head blade screws One M6 x 14 flange screw with lockwasher One wood pendant One coupling Three wire connectors Two threaded studs Two lockwashers Two knurled knobs One clevis pin One hairpin clip The upper foam pad serves as a
11. ght fixture turn electricity off at the main fuse box at this time and remove the existing light fixture dx WARNING To avoid fire or shock follow ail wiring instructions carefully Any electrical work not described in these instructions should be done or approved by a licensed electrician a WARNING Turning off wall switch is not sufflclent To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock _ 3 Ceiling Fan Assembly 1 Pass the 42 motor leads through the opening in the ceiling cover Be sure the cover is oriented aarti correctly Figure 1 Ms x 10 COUPLING SETSCREWS Separate untwist and unkink the three motor leads sn Route the motor leads through the hanger ball downrod assembly Loosen the two screws in the motor coupling Align the clevis pin holes in the downrod with the holes in HANGER BALL the motor coupling Install the clevis pin and secure DOWNROD ASSEMBLY with the hairpin clip Figure 1 The clevis pin must go through the holes in the motor coupling and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the ae hairpin clip snaps around the clevis pin The hairpin M5 x 10 clip must be
12. ing and wiring your fan M5 x 6 WASHER HEAD BLADE SCREW 3 mi Figure 2 a Zp Co 2 FLANGE SCREWS 2 IZ KA a SWITCH HOUSING CONNECTOR Am MOTOR CONNECTOR uc D a e SWITCH HOUSING MOUNTING SCREW HOUSING ASSEMBLY U L Model No 52 ANT 4 How to Hang Your Ceiling Fan continued 4x WARNING The fan must be hung with at least 7 of clearance from floor to blades Figure 6 4 WARNING The outlet box and Jolst must be securely mounted and capable of supporting at least 50 Ibs Use only a U L outlet box listed as Acceptable for Fan Support of 22 7 kg 50 Ibs or less 44 WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support of 22 7 kg 50 Ibs or less and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt 1 Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box Figure 7 WARNING Hanger bracket must seat firmly against outlet box If the outlet box is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall 2 Carefully lift the fan and seat the hanger ball downrod assembly on the hanger bracket that was just
13. orces warm air near the ceiling down into the occupied space Remember to adjust your thermostat when using your ceiling fan additional energy and dollar savings could be realized with this simple step Turn Off When Not in the Room Ceiling fans cool people not rooms If the room is unoccupied turn off the ceiling fan to save energy U L Model No 52 ANT
14. ounting the fan blade assemblies 8 Rotate the motor hub until the flange screw hole is next to the cutout in the switch housing plate Attach the blade assembly to the motor hub using the two M6 x 14 flange screws preassembled in flange Figure 3 Make sure all screws are tightened Repeat this procedure for the other four blade assemblies The blade flanges have an interlocking feature that must be fully engaged before tightening the screws Make sure all the flanges are properly engaged and then tighten the flange screws If one of the flanges does not seat properly on the motor hub loosen the adjacent flange screws re engage and reseat the flanges then tighten the screws again Engage the connector of the switch housing assembly with the motor connector Figure 4 The two connectors are keyed and color coded and must be mated correctly color to color before they can be engaged Make sure the connector latch closes properly Remove the three switch housing mounting screws Figure 4 from the switch housing plate Position the switch housing assembly on the switch housing plate and align the holes in the switch housing assembly with the holes in the plate Secure the switch housing assembly by installing the three mounting screws Figure 5 NOTE Do not pinch wires between the switch housing assembly and the switch housing plate 12 You have now completed the assembly of your new ceiling fan You can now proceed with hang

Download Pdf Manuals

image

Related Search

Related Contents

Tempo ATA133 QSG  極厚釜 大火力  - WaiTrack© Fleet Management  Catalogue novembre 2014 ( PDF - 190.8 ko)  Brochure CORTO Faucheuses à tambours  Datasheet for XGA & HDTV over Twisted Pair Branching - AV-iQ  SALE I l SELECT  La belle endormie s`est réveillée  E SUSPENSION - Textfiles.com  OS Series 3.qxd  

Copyright © All rights reserved.
Failed to retrieve file