Sea Gull Lighting 31108-965 Installation Guide
Contents
1. Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Attach screw collar D to nipple C STEP 2 Using 2 pairs of pliers open one link of chain G and connect it to the fixture loop I at the top of the fixture STEP 3 Slide the screw collar ring F and canopy E in that order over chain G Open one link on the other end of the chain G and attach it to the screw collar D which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 4 Lace wires up through chain G and pass wires through holes in screw collar D We recommend lacing wire up through every other link of chain G STEP 5 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly a2. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY ASSEMBLY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU Carefully remove the fixture from the carton and check that all parts ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED are included as shown in figure 1 and 2 Be careful not to misplace OR THE CIRCUIT BREAKER SET AT OFF any of the screws or parts which are needed to install this fixture GENERAL STEP 1 Spread the fixture arms R so that the arms are equally spaced You don t need special tools to install this fixture Be sure to follow from each other the steps in the order given Read instructions carefully If you are STEP 2 unclear as to how to proceed consult a qualified electrician Raise positioning disc S STEP 3 CONI CCTONS OUTLET BOX Secure set screw Z with allen wrench provided GROUND WIRE e R Ip AN PE MOUNTING Cor l OUTLET 4 4 BOX SCREWS S gt GROUND FIXTURE lt WIRE S ARMS R NUT B NIPPLE C lt _ SCREW COLLAR D 1 W i ETP lt SCREW CHANG COLLAR RING F lt CANOPY E FIXTURE POSITIONING LOOP I DISC S FIXTURE ARMS R Oo l a aie Sea gul lighting Installation And Safety Instruction HC 891 050405 FIGURE 1 NOT INCLUDED Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 891 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET OX U STEP 1
3. gainst the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw R is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire S from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw R on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire S from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all UL specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefu
4. lly inside outlet box and then raise the canopy E against ceiling and screw the screw collar ring F to the screw collar D Install bobeche X and candle covers Q STEP 3 Install lamps CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX GROUND WIRE le WIRE ie CONNECTORS A BAR A A OUTLET BOX j SCREWS o E GREEN NUT B GROUNDING SCREW R NIPPLE C FIGURE 2 NOT INCLUDED
Download Pdf Manuals
Related Search