Sea Gull Lighting 65662-839 Installation Guide
Contents
1. listed wire connector to connect the fixture hot wire black wire or round and smooth tracer to the supply hot wire B Use a listed wire connector to connect the fixture common wire white wire or square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection STEP 6 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 7 After wires are connected tuck them carefully inside outlet box and then raise the canopy D against ceiling and thread the screw collar ring F to the screw collar E STEP 8 Install lamps not supplied STEP 9 Place diffuser J into decorative ring L Raise decorative ring L to the fixture ring M so mounting studs O protrude through both rings Secure by threading retaining screws N onto mounting stud a STEP 12. 0 Place washers over threaded holes of top diffuser mounting area Place washers onto top diffusers W and secure by threading top diffuser retaining screws V through top diffusers W washers and threaded holes of top diffuser W mounting area TOP DECORATIVE DIFFUSERS FIXTURE RING L w RING M DIFFUSER RETAINING SCREWS V RING L MOUNTING STUDS 0 RETAINING FIGURE 3 SEREWS h NOT INCLUDED FIGURE 2 amis OUTLET BOX Ka AWIRE CONNECTORS SF H GROUND WIRE t MOUNTING BAR A H lt OUTLET BOX SCREWS SCREW COLLAR E SCREW COLLAR RING F DIFFUSER J NOT SUPPLIED
3. LAR RING F ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when iN pal CHAIN G BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture e ok D ar Q ge S a o FIXTURE LOOP H INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Thread fixture loop H to fixture STEP 2 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 5 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 3 Using 2 pairs of pliers or chain break open one link of chain G and connect it to the fixture loop H at the top of the fixture Chain should be opened outward do not twist STEP 4 Slide the screw collar ring F and canopy H in that order over chain G Open one link on the other end of the chain G and attach it to the screw collar E which has been mounted to the nipple C FIGURE 1 NOT SUPPLIED BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY DIFFUSER J WIRING HC 1436 STEP 5 A Use a
4. Na Installation And Safety Instructions HC 1436 il li hbj Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to sta gu ig mg this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 112508 IMPORTANT SAFETY INSTRUCTIONS Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of OUTLET BOX the fixture e f you are unclear as to how to proceed contact a qualified electrician e You don t need special tools to install this fixture Jj WIRE CONNECTORS e Be sure to follow the steps in the order given e Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a GROUND WIRE ceiling which contains a radiant type heating system MOUNTING BAR A e Read instructions carefully NUT B i a e Save these instructions S g lt en NIPPLE C j CLEANING s CANOPY D To clean wipe fixture with a soft cloth Clean glass with a mild soap l Do not use abrasive materials such as scouring pads or powders SCREW COLLAR E steel wool or abrasive paper SCREW COL
Download Pdf Manuals
Related Search