Sea Gull Lighting 61251-824 Installation Guide
Contents
1. NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors FOR STEM MOUNT AND CHAIN HUNG STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy G against ceiling allowing and screw the screw collar ring F to nipple STEP 2 Install lamp STEP 3 Raise glass P to fixture and secure with retaining ring T CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE J D PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar If uninsulated wire is on the mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied
3. INSTALLATION AND SAFETY INSTRUCTIONS GROUNDING AND MOUNTING BAR LOCK UP WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU OUTLET BOX ARE WORKING ON IS SHUT OFF EITHER THE FUSE IS y4 GROUND WIRE REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF WIRE GENERAL CONNECTORS You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician Was ASSEMBLY E gt OQ pyg BAR A Carefully remove the fixture from the carton and check that all parts pe are included as shown in Figures 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NUT B GROUNDING SCREW D NIPPLE C FIGURE 1 NOT SUPPLIED FOR Ya Y OUTLET BOX FIGURE 2 STEM NOT INCLUDED lt WIRE CONNECTORS NUT W LOCK WASHER H MOUNTING CANOPY G SCREWS I _ a NIPPLE M CANOPY LOOP S COLLAR RING F CHAIN Y COUPLING J QWQwOc xs CANOPY G Slt FIXTURE LOOP X SOCKET ASSEMBLY U FIGURE 3 lt ROD ASSEMBLY E ASSEMBLY FOR CHAIN HUNG Install fixture loop X onto socket assembly U STEP 2 Feed the fixture wire from the socket assembly U through the fixture loop X chain Y and canopy loop S mounted on canopy G RETAINING RING T Sa lt w
4. isn sea gull lighting oe Installation And STEP 1 1 e Secure rods together if applicable Safety n stru cti O n Feed the fixture wire from the socket assembly U through the rod H C O O 3 120604 assembly E and coupling J mounted on canopy G Line art shown may not exactly match the fixture enclosed However STEP 3 the installation instructions do apply to this fixture Fill In Item Number On Carton And Secure rod assembly E to coupling J and socket assembly U rle This cheer ror Endure Reference TIEN Be sure not to damage the fixture wire INSTALLATION HC 883 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX FOR STEM MOUNT AND CHAIN HUNG STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B FOR CHAIN HUNG ONLY STEP 1 Using 2 pair of pliers open one link of chain Y and connect it to the fixture loop X at the top of the fixture BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 2 Lace fixture wire up through entire chain Y and pass through canopy loop S We recommend lacing wire up through every other link of chain Y A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP
Download Pdf Manuals
Related Search