TroposAir 88550 Instructions / Assembly
Contents
1. Secure with twist lock wire nuts 2D Insert receiver into mounting bracket NOTE Do not squeeze all the wires while inserting the receiver into the mounting bracket Mounting Bracket Note Two screws are pre installed on mounting bracket for canopy installation Push up canopy until two screws pre screwed on mounting bracket are engaged with two key holes on canopy Rotate canopy slightly until two pre installed screw heads are engaged in the narrow end of key holes G Tighten both screws Canopy screw 2 Attach blade assembly to spindle Thread the nut to counter clockwise to spindle until fully tightened P5 5 LIGHT KIT INSTALLATION For use with light kit 5A Install the bulbs included to the medium sockets properly 5B Attach the glass shade by screwing it onto the light kit pan clockwise HOD Lamp Holder For non light use 5C Attach the bottom plate by screwing it clockwise onto the light kit pan Turn on power at breaker box for remote setting 6 REMOTE amp SETTING SETTING for light operation before starting fan Pressing the button OFF for 3 5 seconds till the LIGHT BLINKS which means this remote control has done the setting Now the remote is ready for operation D for light dimming for incandescent bulbs LOW Fan low speed MED Fan middle speed HI Fan high speed OFF For SETTING Fan speed for CFL bulbs Note You may switch L2. can be made to work immediately after installation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for slope ceiling 12 This fan is controlled by remote 13 This fan is suitable for indoor use P1 Unpack and inspect fan carefully to be certain all contents are included Mounting __ ff Bracket Hardware Bag For Mounting Bracket Flat Washer x3 Spring Washer x3 l Machine Screwx2 Wood Screw x3 Downrod Assembly For Wire Connection Wire Nut x 3 r 4 a For Blade Installation Nut x3 9 9 9 Canopy _ For Blade Balance Balancing slide x 1 c2 Weight block 3G x 3 OD Yoke o oo Wires amp Safety Cable Blade Assembly 3 Remote Battery Included Bs Hardware Bag Wood Screw x2 S S wente A444 Bottom plate WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable for fan support box to avoid possible Outlet box must support 35 Ibs min electrical shock 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws Outle
3. Owner s Manua roposAfir Tristar 3JUD18 3M This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection Page 5 Canopy Blade installation Page 6 Light kit installation and Remote amp Setting ListTEo Intertek 3110124 Toll Free 1 855 676 7247 Net weight 17 0 KGS 37 4 LBS WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object B
4. able Flat Washer Spring Washer Wood Screw Safety cable j Mounting Bracket 2B Setting code switches for transmitter Remote controls are tuned to operate together using 4 switches for 16 possible code combinations 1 Setting the code on the TRANSMITTER Remove battery cover Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down Slide code switch for light ON OFF marked as X or DIMMING marked as D function Important This fan includes 2 CFL bulbs so the code switch should be at X position ON OFF You may switch code at D position DIMMING once incandescent bulbs are installed Install 9V DC battery Included Install battery cover on transmitter Transmitter Code Switches D for light dimming for incandescent bulbs X for light ON OFF for CFL bulbs A Warning CFL bulbs are not applicable to the remote with dimming function 2C Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts Note Wires from house may vary in color and may not include ground wire green After wiring is completed collect wires neatly inside hanging base From House From Remote From Fan White yl E Motor N Black iene E a eere E Motor L for light kit for ground wire from downrod from mounting bracket
5. ight switch code at D position DIMMING when you change to incandescent bulbs for Down light To use dimming press and hold light button s P6
6. lades should be at least 7 feet from floor when fan is in operation 4 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan
7. t Box gt included with the outlet box and washers from the hardware bag f Mounting f Bracket 1B Installing Downrod and Yoke Remove cross pin and cotter pin from downrod Insert downrod through canopy and yoke cover and feed motor lead wires amp safety cable through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Pull down the yoke cover to cover yoke QWires Downrod cross Pin Cotter Ping gc Canopy q Downrod Jam g i Screw 2 z Cross Pin Loosening W Z ap P Yoke cover X q j Screw 2 U Y2 Tightening Ajquiassy pojumoq lt i 1C Hanging the fan Lift fan assembly onto mounting bracket Rotate fan so that the groove on the ball engages gt the ridge in the mounting bracket f R Mounting n Bracket ALN l S Ni Za Mounting Bracket Fan Assembly 2 WIRE CONNECTION 2A Attaching safety cable to ceiling joist Use wood screw spring washer and flat washer from hardware bag Pass wood screw through closed loop of safety cable Secure wood screw to ceiling joist through any available slot on mounting bracket Make sure safety cable has been tightened securely CAUTION THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS Safety c
Download Pdf Manuals
Related Search