Worldwide Lighting W33015G16 Instructions / Assembly
Contents
1. W 33015C16 D16 H12 L3 We are dedicated to providing the finest quality crystal chandelier for our customers Our master craftsmen and designer pride themselves on their attention to detail prompt efficient service is our priority Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions carefully and thoroughly If you have any questions please fell free to call our toll free DHANDELIER HOTLINE AT 1 855 411 8999 C US Crystal Dressing Instructions W3301 5C1 6 When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals 14mmX1 14mmX2 14mmX4 AN AN AN 40mmX 1 40mmX 1 WOYYyW WOW 14mmX7 B i2strings CANOPY PARTS LIST Existing Electrical Box Crossbar Screws Crossbar Screws x 2 not srpplied Wire Connector Shrinkable tube Cable tie Ground Wire CANOPY INSTALLATION DIAGRAM Frame Parts List 03 Metal Finial 02 Lamp Body WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientati2. lease remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals i So IY SD SD AN My BQ P AN ay ay TEX JKA I dt S IR ASAN ADA i P AN O VYAMA E T l AR WOO Ae WY AN A g AA WAW Ne WZA ASAN ADAN VOW S7 ANSIN SR ANN N A WY AN Gy AN WSL WY ASAN ADAN VOL SO ARNIN AN KKM B WAL ASAN WAAAY WWW MAW WOW VAA WAAI QOS E Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order gt Existing Electrical Box Crossbar Crossbar Screws Metal Plate Crossbar Bracket Neutral Conductor Hot Wire Junction Caps Ground Wire J Wire Hmommoenw z D i SD SD AS AN 7 AS AS SD IY IY SD IY I So My Qa S So I A AN T T AN i AON AAN aS aD D Wr KX Attach the Crossbar B to the existing electrical box A using Woy AYN 1 4 i ANSIN Woy the two crossbar screws E which are not supplied and should RS SN j LOS WR AS P AA OO already be in your box S MAANA A 1 MAW Yy WY AX LIK WAL WY ANSAN I ANAN WOW N T ANNAN BB WOOO NAVAT Kig NAVAVIY ATATA N ATTAT Z ZEN a ANSAN AAAY 5 WAL Wy WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal co
3. mponents of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only T Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the approp
4. on depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only T Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting shall not be responsible for unprofessional wiring Crystal Dressing Diagram When dressing the chandelier with the crystals p
5. riate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation World wide lighting shall not be responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order Fix the Crossbar 01 with junction box Make sure the positive and negative charges of wire and Lamp Body 02 match correctly screw the connect point with the junction cap Make sure the main wire is enough long and keep the rest wire in the 4 J box As the crystal pressing instruction hang the crystal parts Install lighting Source The end
Download Pdf Manuals
Related Search