CDA CI340 washing machine
Contents
1. a safety system for spin drying that prevents spin drying from being carried out if the distribution of the clothes inside the drum is too concentrated This prevents the appliance from vibrating too much e If you find that the clothes are not properly wrung out try spin drying them again after having distributed the clothes more evenly in the drum Ly ww o re O EASY IRON O EXTRA RINSE O INTENSIVE WASH SELECTION ia ii lt x il fig 33 17 Maintenance e After each wash leave the door open for a while to allow the air to circulate freely inside the machine e From time to time depending on the hardness of your water it is recommendable to run a full wash cycle using a decalcifying product This will extend the life of your washing machine Cleaning the Detergent Dispenser e Clean the detergent dispenser whenever there is any washing product residue left inside e Pull outwards on the detergent dispenser to remove it completely Figure 35 e Use warm water and a brush to clean the compartments Figure 36 e Also clean the additive compartment siphons having removed them first Once they have been cleaned put them back making sure that they fit right in to the back Figure 36 e Put the dispenser back into the washing machine The washing machine should be disconnected from the mains electricity supply before any cleaning or maintenance is carried out A dirty or incorrectly fitted2. machine drain or spin dry e If this failure is detected F02 will appear on the display The reasons for the F02 indicator may be the following e The washing machine drain pump blocked building drainage pipes blocked or incorrect p e Solution if the pump is blocked gain access to it as described in section 2 maintaining an Why doesn t the washing machine spin dry This may be due to the following e If this failure is detected C03 will appear on the display e This may be due to an uneven distribution of clothes in the drum and may cause an excessi e The solution is to select a spin drying programme Why can t I see any water in the drum during the wash e This is due to the fact that the washing machine is provided with a system which is able to of fabrics adjusting the levels of water and energy used in order to preserve the environm level you can see through the hatch may look low there is no cause for concern as washing still be optimum Why is there still some water in the dispenser e This may be because the dispenser needs cleaning This simple operation is described in the appliance Why can t I open the porthole door immediately after the wash has finished e Washing machines today are provided with safety systems for users One of these is that cannot be opened until it is certain that the drum is quite still This is why the hatch cann Other indications e The washing machine can detect other indica
3. reaching the plug is the same as that on the plate Do not remove the rating plate The information on it is important Do not plug the washing machine plug into the socket with wet or damp hands To remove the power cord pull on the body of the plug not the cable Electrical information Warning This appliance must be earthed Green amp fellow 10 Earth The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug To cha follow the steps below 1 Remove the fuse cover and fuse 2 Fit replacement 13A fuse ASTA approved to BS 1362 type into the fuse cover 3 Replace fuse cover Important Do not use the appliance without the fuse cover in position How to connect an alternative plug If the fitted plug is not suitable for your socket outlet then it should be cut off and dispose electric shock A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows e The wire which is coloured GREEN and YELLOW must be connected to the terminal whic by the Earth symbol L or coloured GREEN and YELLOW e The wire which is coloured BLUE must be connected to the terminal which is marked with coloured BLACK or BLUE e The wire which is coloured BROWN must be connected to the terminal which is marke coloured RED o
4. siphon will prevent the additives from being taken in and leave water inside the compartment at the end of the wash 18 Cleaning the Filter e Clean the accessible filter if the drain pump is blocked by any foreign objects e Open the kickplate cover with the aid of a coin and by gently pulling open e Place a container under the drain pump filter to collect any water that comes out of it Figure 38 e Remove the drainpipe place it on the container and open the cover Water will start to come out e Half or quarter turn the filter to the left Figure 38 e Water will start to come out Figure 38 e When all the water has drained out of the washing machine turn the filter several times until it can be completely removed by gently pulling on it Figure 39 e Remove the objects or fluff caught in the filter or the drain pump Figure 40 e Put the filter and the filter cap back in place To avoid risk of scalding do not carry out this operation when the wash water is at a temperature of over 30 C Cleaning the Outside of the Washing Machine e The outside of the washing machine should be cleaned with warm soapy water or a gentle cleaning agent Do not use abrasive cleaning products or solvents e It should then be thoroughly dried with a soft cloth Wipe any detergent spills immediately to minimise the risk of damage to the cabinet of your washing machine 19 Safety and Troubleshooting e Ifyou d
5. 4 hours and then press again e The delay will be cancelled when 24 hours have been reached and the button is pressed once more If the programme is changed the delay is also cancelled Additional functions Additional function selection button depending on programmes cll O sron e There are 3 options easy iron extra rinse and intensive wash eane e Press the button and the desired option will be displayed Figure 28 pon INTENSIVE WASH e By pressing the button several times you can choose between several DELAY TIME SELECTION combinations of one two and up to three additional functions at the f 4 C5 tn Ny ai a same time depending on the programme selected Figure 29 fig 28 Option 1 Easy iron easy iron This option prevents garments from creasing by means of carrying out a extrarinse special programme with special turns to fluff out the garments after 6 INTENSIVE WASH spin drying and make them easier to iron DELAY TIME SELECTION or mi Option 2 Extra rinse E fig 29 Increases the level of the final rinse obtained in the clothes suitable for large loads and garments belonging to people with sensitive skin However this option will increase your water consumption Option 3 Intensive wash This option specially recommended for heavily soiled or stained clothes achieves better results by extending the normal wash cycle If during the additional function selection the programme is c
6. CI340 Integrated Washing Machine C D A Manual for Installation Use and Maintenance Contents Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 7 Page 8 Page 9 Page 10 Page 11 12 Page 13 14 Page 15 Page 16 Page 17 Page 18 Page 19 20 Page 21 22 Important information Warnings Washing machine specifications Unpacking the washing machine and removing the transit bolts Connecting to the mains water supply Levelling and electrical information Before first use Preparing garments for washing Detergents and additives Selecting the wash programme Programmes Spin speed and anti crease Time delay Starting up Wash programme phases and power cuts Maintenance and cleaning Troubleshooting Important This appliance must only be used for the purpose for which it is intended i e domestic dangerous and may lead to premature failure of the appliance The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorr product Please note that CDA reserve the right to invalidate the guarantee supplied with th installation or misuse of the appliance Under no circumstances should any external covers be removed for servicing or maintenan qualified personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cu fault with your appliance and to register your appliance for guarantee purposes CE Declarations of Conformity This
7. appliance has been designed constructed and marketed in compliance with safety r 2006 95 EEC Low voltage and requirements of EMC Directive 2004 108 EEC IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN DIRECTIVE 2002 96 EC At the end of its working life the product must not be disposed of as urban waste It m authority differentiated waste collection centre or to a dealer providing this service Disposing of a household appliance separately avoids possible negative consequences for deriving from inappropriate disposal and enables the constituent materials to be recovere in energy and resources As a reminder of the need to dispose of household appliances sep with a crossed out wheeled dustbin Warnings To avoid the risk of fire electric shocks injury or damage when using your washing machin following precautions e Please read all the instructions before using the washing machine e Do not wash items that have previously been cleaned washed soaked or treated with cleaning other inflammable substances or explosives as they produce fumes that coul e Donotadd petrol solvents for dry cleaning or other inflammable or explosive substan produce fumes that could catch fire or explode e Do not repair or replace any part of the washing machine or try to carry out any type o recommended in the maintenance instructions in the manual e Do not climb onto the machine or stand on the open porthole door e Do n
8. ashing special fabrics Anti crease option H e Pressing the spin button again will select the anti crease option Figure 26 e The wash programme stops on the last rinse with the clothes left in water e When the option is deactivated the washing machine continues the programme draining and spin drying e Itis used for example when you are not at home and want to delay the spin drying until you get home to prevent the clothes creasing after spin drying and being left in the drum to be removed DELAY TIME o mm DELAY TIME C5 n i DELAY TIME en Sa Pi O EASY IRON O EXTRA RINSE O INTENSIVE WASH SELECTION Fa Te Ye fig 23 O EASY IRON O EXTRA RINSE O INTENSIVE WASH SELECTION in k a fig 24 O EASY IRON O EXTRARINSE intensive wasH SELECTION Pn ta fig 25 C EASY IRON O EXTRA RINSE O INTENSIVE WASH SELECTION a i j fig 26 Time Delay Time delay selection button O EASY IRON O EXTRA RINSE e A delay of up to 24 hours can be selected The delay must be selected after choosing the wash programme for INTENSIVE wash SELECTION e To select the hours of delay press the time delay button Figure 27 Each time the button is pressed the delayed start of washing is increased by one hour fig 27 Cancelling the delay e To cancel the delay press the time delay button repeatedly to cycle through the full 2
9. concentrated detergents exist which are more environment and nature friendly The use of more detergent than necessary will not improve your washing results and apart from costing you money it will have a negative effect on the preservation of the environment We therefore recommend you follow the detergent manufacturer s instructions 10 Selecting the Wash Programme Start stop button Screen Detergent dispenser Programme Spinand Time delay Additional function selector dial anti crease button button button To select a wash programme e Press the programme selector dial to release it Figure 20 e Select the wash programme by turning the programme selector dial Figure 20 See programme table e The display on the control panel will light up Selecting the Wash Programme When you select the programme the following information will be displayed 1 Wash programme phases Prewash Wash Rinse Spin drying and draining 2 Spin speed 3 Programme number for a few seconds and then programme duration 4 Additional functions Easy iron Extra rinse Intensive wash There are four types of programme Normal programmes Delicate programmes Wool programme Auxiliary programmes 8 Delicate cold 12 Wool 35 C 3 Normal 30 C 10 Ddicate 40 C 15 15Draining 5 Normal 602C 7 Prewash 7 Prewash 60 C Eco Note We recommend you choose a wash programme without prewash whenev
10. er possible This will save you money and help protect the environment ww w emen anan aman an ama 1100 89 88 1100 8 8 88 11 Washing Machine Programmes LEE mi Sato Deka Weoob wool m Le nean mi Waaa ma lt aan Libr Pean Cao E AANE TER Sarii ee Wana asa miki Sears u et ed ee ee ee F boc es eF ie jee Se oe ee TL 12 Washing Machine Programmes i ET ET biorra sear rr asin ae ape d deed pd long Are aren E MOTT wai rirens Vitel Gales dase pa desired and Coe smi Fire BT ee pee aes f Sere ite gnia rad spri 13 14 Spin Speed Selection and Anti Crease You should first select the wash programme and then select the wash options Changing the programme cancels the preset selected options Each selected programme has its own preset spin speed Spin speed e You can reduce the spin speed or remove it completely by pressing the spin button Figure 23 e The spin speed will gradually reduce each time the spin button is pressed at 100 r p m intervals to a minimum of 400 r p m Figure 24 No spin e Press the spin button again to get to the no spin option and the display will show 0 Figure 25 e A programme without a final spin is used to prevent creasing when w
11. etect any problems with your washing machine you will probably be able to rectify consulting the following instructions e If this is not the case unplug the appliance and contact the technical assistance number Do not open up the washing machine It does not contain any fuses or similar com be replaced Indicator Problems C03 Does not spin dry TAA oes not start FOS F10 Call the Technical Assistance Team Problems Why won t the washing machine start This may be due to the following e Check the door is properly shut e The washing machine is not plugged into the mains or there is no voltage in the mains sup e The Start Pause button has not been pressed e Ifthe washing machine door is not properly shut F04 will appear on the display Why is the washing machine vibrating or making too much noise This may be due to the following e The blocking and transport screws have not been removed e The washing machine has not been correctly levelled e Onspin drying the motor makes a kind of whistling noise This is due to the mechanical a itself and is perfectly normal Why doesn t the washing machine take in water e If F01 shows on the display this may be caused by a cut in the water supply a tap turned o water inlet filter e The possible solutions are as follows wait for the water supply to be reconnected turn water inlet hose and clean the filter 20 Problems Why doesn t the washing
12. hanged or the Start Stop button is pressed all the functions selected until then are cancelled Starting Up Start Pause button e To start up the washing machine you have to press the Start Pause button Figure 30 e The time remaining in minutes until the end of the programme will appear on the display at all times Lock Function Lock function selection e The lock function ensures that the programme will not be affected if any buttons are pressed It is used when children could press the buttons etc e The lock function should be activated after the wash programme has been selected together with all its options Activating the lock function A e The lock function is activated by pressing the Start Pause button and holding it down for at least 3 seconds Figure 31 e The display will show the lock symbol if it is activated Deactivating the lock function e The lock function is cancelled when the wash programme comes to an end Figure 32 e Ifyou want to deactivate the lock function before the end of the programme you have to hold the Start Pause button down again for at least 3 seconds e After 3 seconds the lock function indicator will disappear from the display and it will go into pause status e The Start Pause button does not cancel the lock function 16 Wash Programme Phases and Power Cuts Programme Phases 900 e When the programme is running the programme phase and the time remai
13. ning will appear on the display Figure 33 DELAY TIME Pins I a e The active phases will appear successively at the top of the display as the programme progresses Figure 33 The time remaining until the end of the programme will also appear on the display It updates at regular intervals but not minute by minute e Any option button can be selected provided the wash phase in which it takes effect has not been passed and when the programme accepts the option e Pressing the time delay button during washing will have no effect on the wash programme e Pressing the Start Pause button during the wash activates the PAUSE function If the programme is changed on the selector dial during the washing and drying process the washer will go onto PAUSE status and the programme will be cancelled If you need to add or remove a garment press the Start Stop button and make sure that the water level is not above the door overflow level and that the temperature inside is not high Press the Start Stop button again to restart the wash from the same cycle phase it had stopped at Power Cuts e If there is a power cut when the electricity comes back on the washing machine will continue to run from where it left off it has several hours of memory Warnings and Advice e Try to wash clothes of different sizes in the same wash programme to favour the distribution of the clothes inside the drum during spin drying e All the models have
14. ot use an extension lead or adaptor to connect your washing machine to the main e Follow the washing instructions recommended by the manufacturer of the garment to be washed e Do not turn your washing machine on until you are sure that It has been installed in accordance with the installation instructions All the water drainage mains electricity and earth connections meet the local regulatio applicable regulations Important Ensure that the transit bolts have been removed prior to using the m Washing Machine Specifications Power co Drain hose Control p Detergent di Stainless stee Porthole door Accessories Water inlet hose Unpacking the Washing Machine e Remove the base corner protectors and top cover Figure 1 Removing the Transit Bolts e Remove the screws holding the plastic covers to the back of the washing machine Figure 2 and 3 e Loosen and remove the 3 transit bolts Figure 3 e Cover the holes with the plastic covers you have just removed Figure 2 Do not throw the transit bolts away If you need to move the washing machine after installation you should first replace the transit bolts Connecting to the Mains Water Supply The water supply hose is located inside the drum e Connect the bent end of the hose to the threaded inlet of the electrovalve located at the rear of the washing machine e Connect the other end of the hose to the water in
15. r BROWN If in doubt regarding the electrical connection of this appliance consult a qualified electrician supply cable the appliance may require removing for servicing N B Ensure that the plug socket is situated in an easily accessible place Before First Use e When your washing machine has been correctly installed we recommend that you pre clean the machine This is to check that the installation the connections and the drainage are all correct and to thoroughly clean the inside of the washing machine before any wash programmes are run see the operating instructions on the following pages e Prior to pre cleaning you should ensure the transit bolts have been removed e Select the normal programme at 60 C Figure 11 e Press the Start Stop button Figure 11 Preparing Garments for Washing Preparation e Before placing the clothes in the drum make sure all the pockets are empty Figure 12 Any small objects may block the drain pump Sorting the Clothes Sort the clothes according to fabric and how they are made e We recommend using the delicate programmes for sensitive fabrics There is a special wool programme for woollens Figure 13 e Sort clothes according to how soiled they are Figure 14 e Wash lightly soiled garments using a short programme e Use a programme without prewash for medium soiled garments e Wash heavily soiled garments using a long programme with prewash e Sort you
16. r clothes according to colour Figure 15 e Wash whites and coloured separately We recommend loading the washing machine to its full capacity for best water and energy efficiency Whenever possible we recommend that you wash garments of different sizes within the same wash programme This improves the washing action and also aids the correct distribution of the garments in the drum when spin drying and the washing machine will therefore be quieter We recommend that small garments are placed in a wash bag Detergents and Additives Your washing machine s detergent dispenser has three compartments e Add the detergent or additive to the detergent dispenser before starting the wash programme Figure 16 e Liquid detergents may also be used in this washing machine An optional detergent dispenser Figure 17 is available for this which can be obtained from CDA Customer Care e Place this optional dispenser inside the wash compartment Figure 18 The level of liquid must never be higher than the MAX mark printed on the dispenser wall Remember that the amount of detergent to be used will always depend on e The amount of clothes to be washed e How heavily the clothes are soiled e The hardness of the water Information on water hardness in your area can be obtained from your local water board We recommend the use of a decalcifying product if the water hardness is high in your area Eco Note Remember that
17. take Then securely tighten the connecting nut The drain hose must be securely fastened to the outlet to prevent any risk of the drain hose becoming detached and causing flooding The washing machine must be connected to the mains water supply using the new supply hoses supplied with the appliance Do not use water supply hoses that have been used previously For your washing machine to work properly the mains water pressure must be between 0 05 and 1MPa 0 1 10 bar Drainage Connection e It is recommended that you have a fixed drainage outlet 50 to 70 cm from the floor e Avoid the drain hose being too tight kinked or restricted e The water outlet can either be connected to a water drain or to a sink outlet spigot This connect should be a minimum of 50cm anda maximum of 110cm from the floor The drain hose should be no longer than 4m in length to ensure good performance from the dishwasher e After connecting the water supply check to ensure there are no leaks Levelling e To reduce the noise level from the washing machine and to prevent unnecessary movement during use you should ensure the washing machine is level using the adjustable feet Please note Raising the washing machine too high can affect the stability of the appliance Electrical Connection e Check the rating plate located on the porthole door of the washing machine before connecting the appliance to the power supply Ensure that the voltage
18. tions When this happens a number of othe display F05 F06 F10 If this happens call CDA Customer Care 21 CDA To contact our Customer Care Department or for Service please contact us on the details below
Download Pdf Manuals
Related Search