Sea Gull Lighting 78240-780 Installation Guide
Contents
1. E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated ground wire is on the mounting bar A connect the ground wire from the fixture and the outlet box to it using a small wire connector not supplied See Figure 2 NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise the canopy E to the ceiling allowing for mounting screws I to protrude through key slots N Rotate canopy E clockwise until screws l are in narrow part of keyslot N Tighten screws I with screwdriver STEP 2 Install lamps STEP 3 Raise diffuser H to canopy E so that screw holes line up Secure in place by threading ball nuts retaining screws G through diffuser and canopy CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet fo2. INSTALLATION AND SAFETY INSTRUCTIONS NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C e Be sure the electricity to the system you are working on is turned SUPPLY WIRE WARNING ONLY RISK OF FIRE MOST off either the fuse removed or the circuit breaker set at off DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE e Use of other manufacturers components will void warranty listing RATED 60 C CONSULT A QUALIFIED ELECTRICIAN and create a potential safety hazard BEFORE INSTALLING e If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully Save these instructions GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX SCREWS MOUNTING BAR A MOUNTING A BAR A P A URE D F T MOUNTING EN FIXT MOUNTING SCREWS 1 Pe OUTLET BOX GROUNDING SCREWS SCREW D NOT INCLUDED WASHER FIGURE 2 F KEYSLOTS N COUPLING M RETAINING SCREW DIFFUSER H BALL NUT G DEJ gull lighting Installation And Safety Instructions HC 1184 60 File This Sheet For Future Reference ITEM a Line art shown may not exactly match the fixture enclosed FIGURE 1 FINIAL L gt _ NOT SUPPLIED However the installation instructions do apply to this fixture BEFORE YOU BEGIN HC 1184 Carefully remove the fixture from the carton and check that all parts are included as shown
3. in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Raised side is top as illustrated STEP 2 Thread fixture mounting screws l into threaded holes of mounting bar A 3 turns each STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below i i GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED qc NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection
4. r future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search