Sea Gull Lighting 5328-962 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned Carefully remove the fixture from the carton and check that all parts off either the fuse removed or the circuit breaker set at off are included as shown in figure 1 and 2 Be careful not to misplace e Use of other manufacturers components will void warranty listing any of the screws or parts which are needed to install this fixture and create a potential safety hazard e If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully Save these instructions NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE GROUNDING AND MOUNTING WARNINGS ARE PROVIDED ON THE U L LABEL BAR LOCK UP AND ONTHE FIXTURE CARTON RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE 7 OUTLET BOX SUPPLY WIRE RATED 60 C CONSULT A 7N GROUND WIRE QUALIFIED ELECTRICIAN BEFORE INSTALLING 74 a MOUNTING SCREWS WIRE OUTLET BOX CONNECTOR i MOUNTING lt NUT B BAR A GROUNDING FIGURE 2 SCREW D lt NIPPLE C NOT SUPPLIED NUT B NIPPLE C CANOPY Z CENTER i HOLE Sa gull ighting RETAINING SCREW E Re cape Installation And oao Safety Instruction HC 1 67 051908 Line art shown may not exactly match the fixture encl2. d soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
3. lockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire M from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire M from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES STEP 4 Thread three diffuser retaining screws E in side of canopy Z FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise canopy Z to the ceiling allowing for nipple C to protrude through center hole K in canopy Z Secure in place by tightening cap nut F STEP 2 Install lamp s STEP 3 Raise diffuser G to canopy Z and finger tighten retaining screws CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mil
4. osed However the installation instructions do apply to this fixture DIFFUSER G Fill In Item Number On Carton And FIGURE 1 NOT INCLUDED File This Sheet For Fixture Reference ITEM INSTALLATION HC 167 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B STEP 2 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER J R TT BROWN GOLD OR BLACK WITHOUT BROWN GOLD OR BLACK WITH TRACER TRACER RE Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector c
Download Pdf Manuals
Related Search