none 5291F2BXS Instructions / Assembly
Contents
1. 17 While the person continues to hold the vase tipped Air Line the other installer should firmly press the three hole stopper into place in the bowl s center hole Then set the Water tube Light power cord ______ Restrictor vase down 17 Reach into the vase to move one air stone into Air Line position under each window This will give optimum Air check valve bubbling visibility This may also be a good time to AirLine on ee ee eee place any desired colored lenses onto the light Air Pump e eae eae Customers have found the red lens to give a volcanic ae ee i RE Re appearance while no colored lens provides the brightest m Pn eres we effect Pump ae cord 18 Fill the bowl with water Read the instructions for the pumps and light kit Do not use any of these devices unless protected by a GFCI 19 Turn on the water pump Once the vase fills check to make sure it is level that water is running down all sides evenly If not you can adjust the level by inserting the shims provided under the bottom of the vase 20 Attach the light power cord to the light transformer and plug in according to instructions 21 Insert the air check valve into the air line with the arrow on the valve pointing toward the center of the fountain Attach another short air line and then attach to the exhaust fitting on top of the air pump If your air pump has two air outlets at the top take the rubber cap off th2. SETTING UP A HENRI STUDIO VESUVIO FOUNTAIN 1 Position the fountain bowl on a level firm base which will not change over time Note that a channel runs under the bowl to the center hole This allows for two power cords and an air tube to be pulled out of the bowl Make sure that the positioning of the bowl will allow for these lines to be pulled through 2 Find the long air tube and the light Place the two hole stopper around the air tube and the light power cord allowing about 6 of each to extend about the stopper 3 Attach the H shaped tee assembly to the end of the air tube as shown in the drawing below 4 Attach a short air tube and air stone to each of the remaining H tee assembly ends as shown in the drawing below 5 From the top of the concrete vase you can tip it or lay it down according to your preference insert both the other end of the long air tube and of the light power cord through the large hole in the floor of the vase Pull them through gently until the two hole stopper is near the hole Then firmly press the stopper into the hole 6 From the top of the vase insert the short brass nipple into the other smaller hole in the vase floor 7 Thread the brass check valve onto the nipple 8 Now moving under the vase thread the 1 2 barbed adapter into the smaller hole 9 Attach the water tube to this adapter and secure with a clamp 10 Slip the restrictor onto the other end of the water tube and t
3. e side intake of the pump and place over the unused line on the top fitting Plug in your air pump and enjoy your new fountain l Light power cord IMPORTANT WINTER CARE Winter ice build up can cause damage to concrete statuary Follow these tips to reduce winter weathering to your fountain Disconnect power to pumps and lights Remove plugs stopper in all fountain bowls to open drains and let all moisture out Keep drains open throughout winter Place an absorbant material like burlap blankets etc inside vases bowls and cover all with a Henri fountain cover Do not allow snow or ice to build up on or against the concrete Remove snow before it turns to ice Do not use salt or chemical ice removers as these may damage concrete By following these simple and sensible precautions during the winter season you will protect your fountain for years of beauty and enjoyment
4. ighten it enough that it holds firmly in place on the tube about 6 from the open end 11 Thread the 34 barbed adapter into the water pump exhaust top of pump 12 Attach the open end of the water tube to the pump exhaust adapter and secure with a clamp 5290F2 amp 5291F2 VESUVIO FTNS VASE CUT AWAY VIEW Air stone Air tube YS Tee air tube amp tee assembly H4 Air tube y Air stone Air tube Air stone Light Check k a gt n Brass Nipple Stopper 1 2 Adapter Clamp Water tube a Restrictor Air tube Light power cord Clamp 3 4 Adapter i Pump Pump power cord 5290F2 amp 5291F2 VESUVIO FINS 13 Find the three hole stopper This will make the bowl water tight while allowing the power cords and air tube to exit the bowl 14 Place the three hole stopper around the air tube light power cord and water pump power cord It should be positioned on all three lines about 24 from the floor bottom of the vase 15 Insert these three lines through the center hole of the bowl and pull them out to the side of the bowl Make sure they run along the bowl s built in channel underneath 16 Once most of the lines are pulled out have one person hold the vase in the middle of the bowl Tip it back so the lines can be watched Have another person outside of the bowl to pull the air line and power cords out the channel until little slack remains under the vase
Download Pdf Manuals
Related Search