AZEK C044-001 Installation Guide
Contents
1. AZEK Pavers Designed to last beautifully TRIM MOULDING DECK PORCH RAIL PAVERS Bullnose Paver amp Transitlon Paver Install Guide Installing AZEK Resurfacing Bullnose Pavers u cccccesscsesseeeeeseeeseeeeaseeeeaueeeeeeseeeeeeeneenas 2 Installing AZEK Resurfacing Transition PaVers ccscsssesseessesseeseseeeseeseaseeeeeeeeeaeessaeeenas 3 Patterns eae ie eR RE PERE Ser Tort Re er Oe Oo een en err eer ee ane een ee eee yee 4 Installation Guidelines AZEK Pavers should be installed in accordance with the local building codes and the installation guidelines AZEK Building Products Inc accepts no liability or responsibility for the improper installation of this product AZEK Pavers may not be suitable for every application and it is the sole responsibility of the installer to be sure that AZEK Pavers are a fit for the intended use Since all installations are unique it is also the installer s responsibility to determine specific requirements for each flat roof application AZEK Building Products recommends that all applications be reviewed by a licensed architect engineer or local building official prior to installation A STOP Read this section before you start For most current care and cleaning technical information and more visit www azek com e Do not install where standing above ground Do not install for use as a fire pit Grills and fire water conditions are anticipated Proper bowls may be used2. Screw down the visible tabs into the Grid using 1 Screws Do not screw into subsurface Slide adjacent Transition Pavers into place until finished May need to cut off exterior tabs Let cure for a minimum of 72 hours Page 3 AZEK 8x8 4x8 and 4x4 Standard Paver Patterns Pavers Pattern 1 STARTING CORNER STARTING CORNER 57 1 4x8 28 6 4x4 14 3 e Lay out Grids as illustrated above e Begin laying Pavers at the starting corner as indicated e Pavers should interlock the Grids e Compatible with both 4 and 8 soldier course borders Page 4 AZEK 8x8 4x8 and 4x4 Standard Paver Patterns Pn Pattern 2 STARTING CORNER STARTING CORNER Cee eee a x 3 6 0 8x8 44 4 e 4x8 44 4 4x 4 11 1 e Lay out Grids as illustrated above e Begin laying Pavers at the starting corner as indicated e Pavers should interlock the Grids e Perimeter 8 x 8 pavers can be replaced with 4 x 8 pavers to create an 8 soldier course border Page 5 AZEK 8x8 4x8 and 4x4 Standard Paver Patterns Pavers Pattern 3 STARTING CORNER STARTING CORNER AAH EZA e 0 o E 8x8 25 e 4x8 50 4x4 25 e Trim Grids as illustrated above e All parts of quarter Grids and half Grids can be used e Begin laying the Pavers at the starting corner as indicated e Pavers should interlock the Grids e Adding a 4 or 8 soldier course would eliminate the need to cut
3. 72 hours Page 2 SUB STRUCTURE GRID LEAVE 6 5 7 OF GRID REMAINING 4X8 PAVERS IN DESIRED PATTERN AZEK Installing AZEK Resurfacing Transition Pavers Pavers Resurfacing Transition Pavers GRD APPLY ADHESIVE SCREWTABS TRANSITION PAVER SUB STRUCTURE TRANSITION PAVERT TRANSITION PAVER TO BE FULLY SUPPORTED BY SUB STRUCTURE 7 4X8 PAVERS IN DESIRED PATTERN CUT TRANSITION PAVER 1 AS SHOWN a SI x GRID SUB STRUCTURE TRANSITION PAVER SCREW TAB P ha APPLY ADHESIVE S GRID SU SIRT TRANSITION PAVER TRANSITION PAVER TO BE FULLY SUPPORTED BY SUB STRUCTURE Corner Assembly CUT TRANSITION PAVER 2 AS SHOWN 4X8 PAVERS IN DESIRED PATTERN SUB STRUCTURE Choose a starting point based on the dimensions of the project and the desired pattern Trim expansion nubs off front edge of grid Apply 1 4 bead of adhesive to the top ribs of the Grid Titebond PROvantage Landscape Adhesive is recommended Place Transition Paver onto the Grid pressing firmly
4. SUB STRUCTURE Cut Grid to allow for adeguate interaction of Grid and Paver and so the bottom of the Bullnose Paver is fully supported Choose a starting point based on the dimensions of the project and the desired pattern 4X8 PAVERS IN DESIRED PATTERN CUT BULLNOSE PAVER 3 AS SHOWN id BULLNOSE PAVER 4 AS SHOWN CUT BULLNOSE PAVER 2 AS SHOWN CUT BULLNOSE PAVER 1 ASSHOWN Corner Assembly o BULLNOSE PAVER SCREW TAB APPLYADHSVE TT T GRID SUB STRUCTURE LEAVE 6 5 7 OF GRID REMAINING BULLNOSE PAVER I Hl IT LI T r BULLNOSE PAVER TO BE FULLY SUPPORTED BY SUB STRUCTURE Fasten Grids on stair treads using 1 5 screws Do not fasten grids on deck or flat roof surfaces Apply 1 4 bead of adhesive to the top ribs of the Grid Titebond PROvantage Landscape Adhesive is recommended Place Bullnose Paver onto the Grid pressing firmly Screw down the visible tabs into the Grid Do not screw into deck boards except on stairs Screws are not recommended on flat roof applications Slide adjacent Bullnose Pavers into place until finished May need to cut off exterior tabs e Let cure for a minimum of
5. grids Page 6 AZEKy note Pavers AZEK Pavers Designed to last beautifully AZEK Building Products Inc 888 North Keyser Avenue Scranton PA 18504 WWW AZEK com 877 ASK AZEK 877 275 2935 2014 AZEK 03 14
6. when placed over a fire mat sub base grading and other storm water to prevent any damage from burning embers management designs should prevent the appearance of water at grade level In areas e Failure to install AZEK Pavers in accordance where small pooling occurs adhesive can be with applicable building codes and this used to affix the pavers to the grids to increase Installation Guide may lead to personal injury installation integrity affect product performance and void the product warranty e Do not install where high volume vehicle traffic is expected e g crosswalk AZEK Pavers are Please call AZEK Customer Service at designed for low volume low speed vehicle 1 877 ASK AZEK or visit our Support Center at traffic e g driveways parking lots www AZEK com AZEK Installing AZEK Resurfacing Bullnose Pavers Pavers Resurfacing Bullnose Pavers LEAVE 6 5 7 OF GRID REMAINING APPLY ADHESIVE GRID SCREW TABS BULLNOSE PAVER ATM SUB STRUCTURE o o o E o o BULLNOSE PAVER J ELLE J Tor 1 BULLNOSE PAVER TO BE FULLY GRID SUPPORTED BY SUB STRUCTURE
Download Pdf Manuals
Related Search