Monticello Mont-12-BK Instructions / Assembly
Contents
1. The base has predrilled holes in the inside and outside bolt channels so you can easily secure your greenhouse to a wood platform Screw 5 4 screw into hole in base through weed until screw is flush with base profile Continue process around outside and inside of greenhouse until it is evenly secured NOTE 5 4 screw is designed to used with wood When securing base to foundations made of materials other than wood use an appropriate fastener 112 Usesk 1 ground anchors with six A 2 anchor brackets on the inside of the greenhouse to secure it to the ground Place one on 11 2B Serew each A 1 ground anchor through sach side at the front center and back hele in center of bracket Usea screw driver through the top of 11 24 Attach each anchor bracket with two A 1 anchor to screw set screws the Inside bolt channels completely into soll base profile Secure each with two bolts Secu greurd2. 4 6 gutters are secured together using B 5 connectors and attached to side profiles using B 3 connectors on the outside of the greenhouse The B 35 connector uses the set screw in the center hole of B 5 connectors at seams Loosen and slide set screws to line up with connectors making sure the seams line up and the gutters remain straight 4 66 Begin at the three seams and arrange set screws so middle screw le centered Fit B 5 connector onto gutter and hold in place using the two end bolts 4 Loosen set screws on side profiles and slide down Fit wide part of B 3 connector onto set screw Slide up into place fitting gutter set screw at other end Tighten set screws and secure with belts NOTE The bottom of B 3 connector extends past the edges of side and __ comer profiles B 3 connector sits over B 5 connector Secure all with balts 20 of 44 WWW COR Assemble Front Wall and Gable Make certaln the places are the correct positions before assembling A Carefully follow the order of assembly to ensure an easy Installation Wear proper safety gear Including work shoes gloves and goggles Prepare required set screws as shown In step 1 1 MOTE Have the hex shaped indent facing up Screw in until itis flush with bottom of mut so it slides easily into bolt tracks After inserting into bolt track screw until it holds in place 5 1 The door frame is 6514 high from the ba
3. at the front Push panel into roof ridges channel until the other end reste on gutter ledge and then slide towards F 1 profile at back _ MOTE W 2 panels are installed in step 8 7 NOTE VIEWS FROM OUTSIDE 6 568 From Inside fit one F 1 profile with 8 50 Hold two profiles together in place at ridge three set screws next to panel Position using one B 4 connector Line up center hole profile so set screws face inside and with long hex bolt in roof ridge Place washer on middle set screw is closer to top Fit ether end into B 4 connector and secure with one bolt Repeat to install 1 profile on opposite side long belt and secure all screws with three bolts B 4 1 5 2 3 5 5 1 35 of 44 COR 8 6 Continue working from back to install section four Femove plastic film from beth sides of one W 1 panel With side marked Resistant facing outside install the next panel on the right at the back Push panel Inte roof ridge channel until the other end rests on gutter ledge 3 and then slide towards F 1 W 1 install W 1 panel left NOTE VIEW FROM OUTSIDE From inside fit one F 1 profile with two set screws facing Inside next to panel Hold in place with one B 4 8 60 Held two profiles together at ridge using one B 4 connecter on right side Secure with two bolts Repeat to install 1 connector Secure with
4. NOTE VIEW FROM INSIDE Assemble Roof Ridge Make certain the places are In the correct positions before assembling Carefully follow the order of assembly to ensure an easy Installation Wear proper safety gear Including work shoes gloves and goggles Prepare needed set screws as shown step 1 1 MOTE Have the hex shaped indent facing up Screw in until it is flush with bottom of nut so it slides easily into bolt tracks After inserting into bolt track screw in until it holds in place Prepare the two 1 and one F 1E roof profiles They will line up in a row and joined using two connectors using a total of eight set screws and two long hex bolts Arrange profile bolt track is facing up Slide set screws into bolt track on each end of profile as shown T 1B Line up three profiles in a straight line with K 1E in the middle Hand tighten set screw on each end of K 1 profile to hold in place 7212 Adjust position of set screws and long hex bolt to fit holes B 5 connector Position each connector with the long hex bolt in center hole and center te the seam where the profiles join Secure B 5 connector by attaching bolts te the set screws HOTE Long hex bolt is Wey RSW CON 30 of 44 7 2 Use twe people and a step ladder Place step ladder inside greenhouse Have one person Inside greenhouse supporting ridge as you slide into position Avold touching top of
5. A Monticello h perahu Made in the USA 8 x 12 Greenhouse Assembly Instructions 071812 nverstone hreen Products fara Brighter Future Customer Service 877 373 3078 Email customerservice amp risew com amp 5 Fleetwood Drive Rockaway MJ 0178645 Introduction Thank you for purchasing your Monticello 8x12 Greenhouse The Monticello lineis proudly made in the USA leading commercial greenhouse maker using the same professional grade materials and design The frame is constructed with the aluminum with lead free powder coated paint The panels are professional grade Smm twin polycarbonate selected for their insulation and durability The Monticello line is a modular system which uses 5x6 greenhouse that can ba easily expanded in four foot sections upto 24 feet by feet at any time This model consists of an 8x8 greenhouse with one four foot extension and includes two roof vente each with it s own automatic vent opener to ensure proper ventilation and maintain optimal temperature When properly assembled and maintained this greenhouse will provide years of enjoyment It be expanded as your needs expand Our greenhouse has been designed to be easily assembled Although all but one step can be completed by one person we recommend using a helper for the entire assembly You will need assistance from another person to assemble the roof Allow six to eight hours to com
6. 9 1 Unpack contents of Automatic Window Opener Screw adjusting knob partially inte threaded end of cylinder Do NOT tighten 9 16 Fit piston rod connected to arm into and oF ayida Turn cylinder wes Palaa yp next te adjusting knob are visible e ar eme 9 1 Continue pushing cylinder onto piston red until holes end of cylinder line up with holes in arm A Push arms apart if necessary Secure with 9 10 Turn adjusting screw clockwise a threaded stud on each side until arms are aproximately 0 45 apart n c A SL eee 7 4 T ie T u B E 2 ic p 2 TT 9 1E Repeat steps 9 1A through 8 1D to prepare the second Automatic Window Opener NOTE You will use the Gripping Channels in next steps You do nat need the other included parts in Window Opener package Handle 9 24 Remove plastic film from both sides of V 2 9 2B Placeopener with arm on bottom factory assembled vents With side labled inside vert Mark screw placement inside facing up lay panel Using 9 1 screw apply pressure to on flat clean surface E puncture the panel and predrill Measure and e holes for next step mark center of vant We RSW CON 39 of 444 9 20 Gerew two 6 1 screws through V 2 panel Line up gripping channel on other side Continue to screw until secure Do not over tighten
7. Assemble Right Wall sssi Ji Assemble Back Wall 14 Assemble Left Wall Assemble Front Wall and Ga ble 21 Assemble Back Gable wuss 27 Assemble Roof Ridge 20 Assemble 22 Install Roof Vents sarcs 20 Install Doors Lo 4 Secure to Platform smaa 44 A Phillips Screwdriver include 23 inch spacer include 5 foot bungee cord finduded RY FUSE a CORR Constructing a Wood Platform IMPORTANT It is very important to begin with level surface Check your foundation to ensure it is level at every point If you are not building on a wood deck we recommend constructing a wood platform so you can properly secure the greenhouse You must assure your foundation is square and level before beginning assembly After choosing a location proper preparation of the site is essential The site must be level Create a wood platform using a perimeter of pressure treated two by fours filled with either soll sod or gravel NOTE When constructing the greenhouse on a wood deck make certain the surface is level Creating an additional wood platform is not necessary Buy pressure treated 2x4 lumber Y ou will use two layers with the corner positions staggered for maximum strength The finished dimensions will be 101 by 14 954 Materials Tools Four 10 pressure treated 2x4 lumber cut to 9712 Spirit Level Four 14 pressure treated 2x4 lumber cut to 14614 Corner Square Sixty five 3 wood screws Phillip
8. as It may damage the vent 3 We 9 2D Repeat steps 9 2A through Do 9 20 to prepare second vent i 3 ae i B a 4 Nx s M Connactor Gripping Chanrel G a 9 3 From inside hold mE opening roof panels Hook R top lip of vent onto curve ridge prole R 1 W2 gt VIEWS FROM FRONT NOTE VIEW FROM OUTSIDE 9 36 Outside of vent rests on top of ledge on W 2 profile Open vent so you can attach the other arm of opener to top of inside W 2 profile Screw two 5 1 screws through panel and into gripping channel on other side to secure Do not over tighten as It may damage the vent 9 3 Espeat steps 98 54 through 9 38 to install second vent NOTE VIEW FROM OUTSIDE Connector 8 4 From inside screw 5 6 screw and spacer into the holes on each end of the top of the vent This will secure the vent to the greenhouse in very windy Seno Inetall Doore Make sure the places are In the correct positions before assembling Carefully follow the order of assembly to ensure an easy installation Wear proper safety gear including work shoes gloves and goggles IMPORTANT The door and doortrack are different for the left and right sides Study the diagrams before installing to ensure you have the parts correctly placed 10 1 From outside prepare to install right and left door tracks The door trac
9. facing inside fit F 1 profile next to right panel F 1 profile rests against widest part of roof ridge and lines up with top of gutter 8 3 From inside hold profile in place with one B 4 connector Secure b mm a NOTE VIEWS FROM OUTSIDE NOTE VIEWS FROM INSIDE 8 30 Fepeat step 8 26 through amp 2C to secure install and secure F 1 profile on left side B 3E Hold two profiles together at ridge using one B 4 connector Secure with two bolts r NOTE WIEWS FROM INSIDE 34 of 44 6 44 Continue working from front right corner Remove plastic film from both sides of one W 1 panel With side marked UV Eesistant facing outside fit 2 top end of panel into channel in roof ridge near corner Push panel into reofridge channel until the other end rests on gutter pr ledge and then slide towards F 7 corner profile Repeat to install W 1 panel in front left corner NOTE VIEWS FROM OUTSIDE 8 40 Hold two profiles together at ridge usin 6 46 From inside fit one 1 profile with two set cg B t Securewith x screws facing Inside next to panel Hold in place with one B 4 connector on right side Secure with two bolts Repeat to install F 1 8 54 Return te back right te install section three and remove bungee cord nearest to back Remove plastic film from both sides of one W 1 panel With side marked UY Resistant facing outside install the nextpanelontheleft
10. from structures that could cause snow to drift on or around the greenhouse Locate underground pipes or cables before preparing the site or anchoring the greenhouse 4 Prepare a Foundation After choosing a location proper preparation of the site is essential The site must be level The greenhouse must be mounted to a bass Construct the base first so the greenhouse can be securely mounted We recommend constructing a wood platform base using a perimeter of two by fours filled with either soil sod or gravel Instructions for constructing a wood platform can be found on page 3 in this manual Other suitable base options include wood decks and concrete slabs Wood screws are included to secure the greenhouse to a wood base The greenhouse le secured to the ground from the Inside with ground anchors See step 1 for details If you are using a concrete base get appropriate mounting screws before beginning Make sure the corners are square by measuring the inside diagonals from both sides and making sure they are equal Use a spirit level ta make sure the base is level Contact your local authorities regarding any required building permits or restrictions 44 Wey RSW CON Tof Safety Advice The greenhouse must be positioned and fixed on a flat level surface Dispose of all plastic bags safely Keep them out of the reach of small children children and pets away from the assembly area until the work is completed Always
11. inch spacer on base next to F 7 corner profile Fit panel into channel 1 profile and slide F 1 profile against spacer to ensure proper placement Position F 1 profiles so single set screw is next to base on inside VIEW FROM INSIDE 4 2D Continue building the side wall from the inside Use the spacer with each panel and the four remaining 1 profiles Repeat steps 4 2A through 4 2C 4 3 Add the last W 1 panel to complete the side From the outside fit 7 corner profile into place and secure with two B 3 connectors Fana 5 2 14 18 of 44 USI CODI 4 4A Prepare two 1 gutter profiles by sliding four set screws Into bottom bolt track Hand tighten each end set screw to hold in place 448 Prepare one 2 2 gutter profile with five set screws and the other G Z gutter profile with six set screws Slide set screws into bottom bolt track Hand tighten end set screw to hold in place 4 5 Working from inside place G 1 and G 2 gutter profiles fitting top edge of W 1 panels into channels of gutters Place one shart 3 1 Se d G 2 gutter profiles in the center Seams are centered to bolt tracks inF 1 profiles 4 5B Place sat screw the inside bolt track of the gutter at each end Hand tighten both set screws to hold place NOTE VIEW FROM INSIDE VIEWS FROM INSIDE WWW RETWW COM 19 of 44
12. to fit heles B 2 channels aera placing side marked UV Resistant facing outside em WARNING The corners of W 5 panels are WES sharp Use extreme caution when handling VIEWS FROM INSIDE 25 of 44 5 9A Prepare two F 7 corner profiles Slide three set screws Into the same bolt track two on one end and one on other end of profile Position one set screw in center of profile It will used in a later step Tighten each set screw to 5 96 From outside fit F 7 profiles inte each side of front a Arrange F 7 profile so channel lines up with tops of panels and the set screws are facing out The side of the profile rests against cut angle of F 3 profile The top end touches edge of F 4 center profile and bottom end touches top of G 1 gutter Position both F 7 profiles NOTE VIEW FROM OUTSIDE 5 90 Use C 1 connector to secure each outside corner Loosen set screws on profiles and adjust position to fit holes in 1 connectors Make sure all profiles line up flush against each other Secure with bolts Repeat on other side 5 9D Cheek inside corners to ensure B 7 connector is still in proper position IF it needs adjusting repeat steps 5 5 and through 5 90 until each corner ls set NOTE VIEW FROM INSIDE Assemble Back Wall Make certaln the places are in the correct positions before assembling A Carefully follow the order of assembly to ens
13. two bolts NOTE VIEWS FROM INSIDE 68 60 Remove bungee cord and remove plastic film from both sides ofone W 1 panel With side marked UY Resistant gt facing outside install the next panel on the en right at the back Push panel inte roof ridge channel until the other end rests on gutter ledge and then slide towards F 1 profile at back Repeat to install ap W 1 panel left B GE From inside fit one F 1 profile with Position profile so set screws face inside and middle set screw 16 closer to top Fit other end inte B 4 connector and secure with one bolt Repeat to install F 1 profile on opposite side ES wall NOTE VIEWS FROM INSIDE E B n Fanal Connector QTY Connector 8 6F Hold two profiles together in place at ridge using one B 4 connector Line up center hole with long hex bolt in roof ridge Place washer on long bolt and secure all serews with three bolts B TA Continue workina from back to install section five Femove plastic film from both sides of one W 1 panel With side marked UV Resistant angle on left F necessary loosen the previous B 4 connector and profile and move them towards the back of the greenhouse to make more room fit panel in place NOTE VIEW FROM OUTSIDE 6 76 Remove plastic film from both sides of one W 2 panel It will be installed opposite the W 1 panel installed in 5 7 F
14. wear work shoes gloves and safety goggles when working s Some of the parts have sharp edges and burs Use extreme caution when handling Do not lean against or push the greenhouse during assembly Take special care not to touch overhead power lines with the aluminum profiles Do not attempt to assemble the greenhouse in windy or wet conditions Do not position your greenhouse in an area exposed to excessive wind IFusing power tools or a step ladder always follow the manufacturer s safety instructions Hot items such as recently used grills blow torches etc must not be stored in the greenhouse Store the polycarbonate panels in a cool dark place such as a garage until you are ready to use them Make sure the greenhouse complies with local building codes General Order of Assembly Step 1 Assemble Base Step 2 Assemble Right Wall Step 5 Assemble Back Wall Step 4 Assemble Left Wall Jt Step Assemble Front Wall and Gable Step 6 Assemble Back Gable Step T Assemble Roof Ridge Step 8 Assemble Roof Step 8 Install Roof Vents Step 10 Install Doors Step 11 Secure to Platform Work Gloves Safety Goggles Step Ladder Tape Measure Spirit Level Toole Needed 20f44 Me Wrench include Table of Contente Introduction ae ae General Order ur RET by 2 Construct Wood Platform 3 Ueied csse cy Prepare Set SCTeWS unus F Assemble Base F
15. RTANT Double check the position and amount of unused set screws in the base You should have 37 available for later assembly 1 5 Measure base diagonally from inside corner Equal measurements ensure the base is square Use a spirit level to make sure the base is level 1 5B Leeate predrilled holes in base profiles Use six 5 4 screws one at each corner and in the center of each side to secure to wood platform You will secure the greenhouse completely to the platform step 11 1 when assembly is finished Wey RSW CON lila Right Wall Make certaln the places are In the correct positions before me Carefully follow the order of assembly to ensure an easy installation Wear proper safety gear Including werk shoes gloves and goggles Prepare required set screws as shown In stap 7 74 MOTE Have the hex shaped indent facing up Screw in until itis flush with bottom ofnut so it slides easily into bolt tracks After inserting into bolt track screw in until it holds in place 21A Prepare twoF 7 corner profiles Slide set screws into all three bolt tracks t on one end and inte two side bolt tracks on other end of comer m t profiles Hand tighten each set screw to hold in place MOTE Set screw in center bolt channel is used when in optional shelving units Install F 7 profile with set screw near base needed 2 16 Prepare five 1 wall profiles Slide set screws into both bo
16. Use extreme caution when handling panels with cut edges The corners are sharp 20 x 57 A f 12 A 24 215 Wavy RET WIE OOP sofa List of Parts continued Connectors QTY Hardware US 1 2 3 4 5 Q 8 7 810 11 7 C 2 2 Step 7 5 54 2 Step 7 S5B 2 Steps Ca s2c 2 Steps m Step 8 Included Tools D 4 127 Step 10 amp of 44 WAW USI CODI Assemble Pase Make certaln the pleces are In the correct positions before assembling A Carefully follow the order of assembly to ensure an easy Installation Wear proper safety gear Including work shoes gloves and goggles 1 1A We use a set screw and nut assembly system for ease of installation With ETT the hex shaped indent facing up mM EN screw S 2B threaded part into 5 2 AJ Wh 6 3 nut until it is flush with bottom QUA of nut When the assembly is flush Fidos easily it will slide easily in the bolt tracks MOTE The two pieces together is referred to in this manual as set screw Shown sliding into F 1 bolt track IMPORTANT end of the 5 2B threaded set screw has a hex shaped indent The other end forms a soft point Make sure indented hex is always facing up when screwed into the 5 2 nut This way if the set screw is installed too tightly to loosen by hand you can use a hex key 1 1B After sliding inte bolt track screw threa
17. all from the inside Use the spacer with each panel and the four remaining F 1 profiles Repeat steps 2 5A through 2 3 24 Add the last W 1 panel to complete the side From the outside fit 7 corner profile into place and secure with two connectors NOTE VIEW FROM OUTSIDE 2 5A Prepare two G 1 gutter profiles by sliding four set screws into bottom bolt track Hand tighten each end set screw to hold in place 2 5H Prepare one G 2 gutter profile with five set screws and the other G Z gutter profile with six set screws Slide set screws into bottom bolt track Hand tighten end set screw to hold in place 2 6 Warking from inside place 5 1 and G 2 gutter profiles fitting top edge of W 1 panels into channels of gutters Place one short G 1 pr at each end and the two longer G 2 gutter profiles in the center Seams centered to bolt tracks in 1 profiles MOTE At front and back edge of G 1 gutter profile lines up flush with edge of F 7 corner profile 2 608 Place one set screw the inside bolt track of the gutter NOTE VIEW FROM INSIDE at each end Hand tighten both set screws to hold in place MOTE VIEWS FROM INSIDE Sw COM 12 of 44 2 7 Thegutters are secured together using B 5 connectors and attached to side profiles using connectors on the outside of the greenhouse The B 3 connector uses the set screw in the center hole of B 5 connectors at sea
18. before assembling A Carefully follow the order of assembly to ensure an easy installation Wear proper safety gear Including work shoes gloves and goggles Prepare required set screws as chown In stap 1 7 E NOTE Have the hex shaped indent facing up Screw in until itis flush with bottom of nut so it slides easily into bolt tracks After inserting into bolt track screw in until it holds in place 3 1A Prepare one F 7 corner profiles Slide set screws into all three bolt tracks aii on one end and inte two side belt tracks on other end of corner a profile Hand tighten each set screw to hold in place MOTE Set screw in center bolt channel is used when installing optional shelving units Install F 7 profile with set screw near base until needed 4 1B Prepare five F 1 wall profiles Slide set screws Into both bolt tracks on one end of profile and ona bolt track on the other end The single set screw will sit on the inside near the base when Installed Te Hand tighten asch ast 4 H screw to hold in place 42 Continue working from inside back left corner Remove plastic film from both sides of one W 1 panel Fit panel into channel in base and corner profile placing side marked UV Resistant facing outside IMPORTANT The panels expand and contract depending on the temperature ensure proper placement use the 23 inch spacer induded with the tools 4 2H Place 28
19. ded part gt farther inte nut so end touches the edge of the E profile and holds in place Do not over tighten will be difficult to loosen again to adjust T position to fit holes in connectors Shown hand tightened in F 1 bolt track NOTE Screwing 5 28 threaded part farther into nut so it holds is referred to in this manual as hand tighten Loosen set screw refers to unscrewing the 5 28 threaded part enough so set screw easily slides We recommend assembling all set screws before beginning Each step shows quantity needed separately Connectors are secured with 5 2C bolt using set screws in later steps 1 2 Thebaseis made up of four P 1 four P 1B one P 2A and one 26 profiles Arrange profiles in a rectangle as shown Position P 2A and P 2B profiles at back sides of the greenhouse IMPORTANT Position P 2A and 2 profiles at back of greenhouse WARNING Use extreme caution when handling profiles P 1A P 1B 2 and P 2E The bottoms may have sharp edges near the drilled holes The cut edges on the comers of these profiles are sharp 7 of 44 1 3 Separate profiles to install set screws into inside and outside bolt tracks Some of the set screws will be secured in this step Most are secured in later steps They are difficult to install after the base is assembled Pay careful attention te ensure you have the correct number of set screws in the correct bolt track in each p
20. front and back of greenhouse until each end is flush with ends of front and back profiles fs ee pure ES UI UTR NING Use two people to install roof ridge Place ladder in inside of greenhouse One person will stand on the ladder holding the ridge until it is in the proper position and secured in place T 2B Make sure end of roof ridge le flush to profiles on front and back 7 3 Working from inside secure roof ridge to front end wall Loosen set screws and adjust position to fit holes in B 7 connector Secure with two bolts T 3B Fepeat step 7 54 to secure back Working from outside ensure all pieces are still flush and secure roof ridge to front Loosen set screws and adjust position to fit holes in C Z connector Secure with three bolts 7 46 Repeat step 7 4 to secure back ar a NOTE VIEWS FROM OUTSIDE 31 of 44 rey FUEL CODI Assemble Roof E 3 i m 4 3 8 A M i IM M PO Hio m i HE iE E H i i HIRE i lis IN a H pede 2 21 F H 8 i Wh ni d Ht 3j a Win Hin 4 HE pA il Hi m 3 H 32 of 4 JRETWVE COM 8 2 The roof panels are installed in the sestlons shown below Use two and a step ladder to assemble the roof Place stap ladder inside greenhouse Have one person stand on ladder inside and guide panel inte channels roof ridge and corner profiles The other person rts the endof the pane
21. gled edge facing up onto corner W 1 panel F 6 profile fits snugly between 7 corner profile and F 1 wall profiles L3 4 N aa BP NOTE VIEWS FROM INSIDE 5 3E From inside line up F 5 profile as shown Make sure B 2 connector is pointing towards door opening 5 3F Adjust set screws and place 2 connector on profiles as shown Slide set screws vertical openings to center of opening B 6 trim z plate will fit properly NOTE VIEWS FROM INSIDE VIEWS FROM INSIDE 6 36 Install B 6 trim plate and secure with three bolts 1 NOTE VIEWS FROM INSIDE Panel 4A Working from inside front right corner install F 1 profile next to W 1 panel Place 23 inch spacer on base next to F 7 corner profile and slide F 1 profile against spacer to ensure proper placement IMPORTANT The panels expand and contract depending on the temperature ensure proper placement use the 23 inch spacer included with the tools two 5 20 bolts MOTE Panels will not fit completely to end of channels There will some space to allow for temperature changes 5 46 Continue working from inside right corner place F 6 profile with mitered end next to corner and angled edge facing up onto EJ corner W 1 panel F 6 profile fits snugly between p F 7 corner profile and 1 wall profiles From inside line up F 5 profile shown Make sure B 2 connector is poi
22. il needed 3 18 Prepare three 1 wall profiles Slide set screws Into both bolt tracks on one end of profile and one bolt track on the other end The single set screw will sit on the Inside near the base when Installed Hand tighten each set screw to hold in place 3 12 Prepare two F 6 profiles Slide set screws 2 10 Prepare two F 10 profiles Slide set screws inte beth bolt tracks on each end of two inte beth bolt tracks on each end of two F 6 mitered profiles Hand tighten F 10 profiles Hand tighten each set screw each set screw to hold in place 3 2 Working from inside remove plastic film from both sides of one W 1 panel Fit panel inte channel in base and corner profile placing side marked UV Rasitant facing outside IMPORTANT The panels expand and contract depending on the temperature To ensure proper placement use the 23 inch spacer included withthe tools 3 2B Place 23 inch spacer on base next to 7 corner profile Fit panel into channel in 1 profile and slide 1 profile against spacer to ensure proper placement Position F 1 profiles single set screw is next to base on inside NOTE Panels will not fit completely to end of channels There will be some space to allow for temperature changes i pd 3 20 FIE B 3 connector and secure with two 5 2 bolts VIEWS ARE FROM IMSIDE 3 2D Continue building the end wall from the inside Use the spacer with each panel and the tw
23. ks are secured with the set screws in F 7 profiles on each side and the two set screws in F 5 profile Remove two bolts from center B 2 connector on F 5 profile Slide set screws to Inside edge of hole NOTE VIEW FROM OUTSIDE ALL VIEWS FROM OUTSIDE 10 18 Loosen set screw in left F 7 profile and position to line up holes in D 1L as shown i IMPORTANT Position 0 11 and D 1R door tracks with lip the bottom when installed 10 1 Loosen set screw in right F 7 profile and position to line up holes in D 1F as shown Loosely secure with bolts c Um EM EE AL N DAR 10 2 From the inside position set screw three inches from right and left 1 door lt 2 frame profiles Install B 5 connector shown and secure each with a bolt ALT 10 3A Working from the outside apply the D 4 door sealant tape to the outside of F 1 profiles that make up the door frame This tape acts as insulation Beginning directly below D 1L and D 1F door tracks smooth tape down to P 1A and P 1B base profile make sure the tape is even Cut each strip at the bottom 10 368 Wrap the top part of each of the B 3 door guides with the D 4 door sealant tape NOTE VIEW FROM INSIDE LaL 10 3C Wrap the bottom part of each of the D 5 door guides with the D 4 door sealant tape NOTE VIEW FROM OUTSIDE 104 Toinstall D 2L factory assembled door rem
24. l from the outelda Section 1 Back two W 1 panels Section 2 Front two W 1 panels Section 5 Next W 1 panel from back right Section 4 Middle four W 1 panels Section 5 Final W 1 panel and two W 2 panels IMPORTANT The panels expand and contract depending on the temperature Under some conditions the panels may require slight force to install Do not use excessive force or you may move profiles out of position When you are having dificulty sliding the panels use dish soap with water on the edges as a lubricant MOTE Use the induded five foot bungee cords for added support They will help hold the sides in position while assembling the roof Remove as you install profiles 6 24 Working from the inside install B 4 connector on every other side profile on both sides of greenhouse Secure each with one bolt NOTE VIEWS FROM INSIDE 8 2B Hook one end of bungee cord into top hole in B 4 connector on each side NOTE VIEWS FROM INSIDE 33 of 44 OOM 6 3 4 Working from back right corner remove plastic film from both sides of one W 1 panel With side marked UY Resistant facing outside fit top end of panel inte channel in K 1 roof ridge near corner Push panel into roof ridge channel until the other end reste on gutter ledge and then slide towards F 7 corner profile Repeat to install W 1 panel back left corner 6 358 With two set screws
25. lt tracks on one end of profile and one bolt track on the ether end The sings set screw will sit on the inside of the greenhouse near the base when installed 2 1C Hand tighten each set screw to hold in place 2 2 Begin at front right corner Remove plastic film from both sides of one W 1 panel Fit panel inte channel in base placing side marked UV Resistant facing outside The panels will help hold the profiles up during assembly 2 2p PlaceF 7 corner profile on base fitting panel into channel Slide set screws into base so they line up Fit B 5 connector on each side S NOTE VIEWS ARE FROM OUTSIDE 2 34 Continue working from inside Remove plastic film from both sides of one W 1 panel Fit panel inte channel in base and corner profile placing side marked UV Fesist ant facing outside IMPORTANT The panels expand and contract depending on the temperature To ensure proper placement use the 23 inch spacer included withthe tools 2 3B Place Z3 inch spacer on base next to F 7 corner profile Fit panel into channel in F 1 profile and slide F 1 profile against spacer to ensure proper placement Position F 1 profiles so single set screw is next to base on inside NOTE Panels will mot fit completely to end of channels There will be some space to allow for temperature changes 2 30 Fit B 3 connector and secure with two S 2C bolts NOTE VIEW FROM INSIDE 2 30 Continue building the side w
26. me position Loosen set screws on profiles and adjust position to fit holes in 1 connectors Fit B 1 connector to profiles as shown BAB Secure each 1 NOTE VIEW FROM OUTSIDE 28 of 44 56 5 Continue working from outside to install panels a shown Ramowe plastic film from both sides of two W 3 and two W 4 panels Fit each panel inte channel in profiles placing side marked UV Resistant NOTE VIEW FROM OUTSIDE WARNING The comers of W 3 and W 4 panels are sharp Use extreme caution when handling NOTE Panels will mot fit completely to end of channels There will be some space to allow for temperature changes 6 64 From outside fit F 7 profiles into each side of back Arrange the profile channel lines up with tops of panels and the set screws on each end are visible Begin with either right or left sida Profile side fits against cut angle of F 3 profile One end touches top of gutter and the top end touches edge of F 2 center profile Position both F 7 profiles VIEW FROM OUTSIDE 6 68 Use C 1 connector to secure each outelde corner Loosen set screws on profiles and adjust position to fit holes in 1 connectors Make sure all profiles line up flush against each other Secure with three bolts Repeat on other sida B 6C Check inside corners to ensure B 7 connector is still in proper position IF it needs adjusting repeat steps 6 68 and 6 60 until each corner 6 set
27. ms Loosen and slide set screws to line up with connectors making sure the seams line up and the gutters remain straight 2 TB Begin at the three seams and arrange set screws so middle screw is centered Fit B 5 connector onto gutter and hold in place using the two end bolts 27C Leosen set screws side profiles and slide down Fit wide part of B 3 connector onto set screw slide up inte place fitting gutter set screw at other end Tighten set screws and secure with bolts NOTE The bottom of B 3 connector extends pastthe edges of side and comer profiles B 3 connector sits over B 5 connector Secure all with bolts 13 of 44 OR Assemble Back Wall Make certaln the places are In the correct positions before assembling Carefully follow the order of assembly to ensure an easy Installation Wear proper safety gear Including work shoes gloves and goggles Prepare required set screws as shown In step 1 7 MOTE Have the hex shaped indent facing up Screw in until itis flush with bottom of nut so it slides easily into bolt tracks After inserting into bolt track screw in until it holds in place Prepare one F 7 corner profile Slide set screws into all three bolt tracks one end and inte two side bolt tracks on other end of corner MOTE Set screw center bolt channel is used when installing optional shelving units Install F 7 profile with set screw near base unt
28. nting towards door opening NOTE VIEW FROM INSIDE NOTE VIEW FROM INSIDE 5AF Install B 6 trim plate and secure with three bolts 5 46 Adjust set screws and place B 2 connector on profiles as shown Slide set screws In vertical m openings to center of opening so B 6 trim plate will fit properly BS TWW CON 23 of 44 5 5 is 6514 high from the base avold adjusting the placement after assembly prepare door frame using the exact measurements listed in these steps 5 54 Prepare one F 4 profile Slide two set screws into bolt track 5 5G Place one end of F 4 profile against F 5 profile on flat level surface Center F 4 profile to F 5 profile and adjust set screws to fit B 2 connector Secure with three bolts a Smm LJ 5 amp 0mmil 22 IMPORTANT F 4 profile is centered to F 5 profile and secured on both sides with B 2 connector 5 5D Turn profiles over and place flat surface Slide two set screws into bolt tracks of F 4 and F 5 profiles Repeat step to place and secure B 2 connector NOTE The inside has two extra set screws on the ends of F 5 profile Working from inside remove plastic film from both sides of two W 3 panels Fit each panel inte channels profiles placing side marked UV Resistant facing outside set screws on ends of F 5 profile and adjust position
29. o remaining 1 profiles Repeat steps 3 2A through 3 ZC 3 3 Add the last W 1 panel to complete the back From the outside fit F 7 corner profile into place and secure with two connectors Ju gt VIEWS ARE FROM OUTSIDE 3 4 Thetwo sete of F 6 and F 10 profiles fit top of W 1 panels Line up bottom bolt channels with top edge of F 1 and F 7 vertical profiles Profiles will 3 44 Working from inside right corner place F 6 profile with mitered end next te corner and angled edge facing up onto corner W 1 panel F amp profile fits snugly between F 7 corner profile and 1 wall profiles 3 46 Continue along back wall Place first F 10 profile on next W 1 panel Make sure profile fits snugly between the two 1 wall profiles 3 40 Place second F 10 profile on next W and ensure it fits snugly 3 4D Place second F 6 profile with mitered end next to corner and angled edge facing up onte corner W 1 panel F 6 profile fits snugly between F 7 corner profile and F 1 wall profiles NOTE ALL VIEWS FROM INSIDE From inside loosen set screws on profiles and adjust position to fit holes in B 1 connectors Fit B 1 connector to profiles as shown 3 58 Secure each B 1 connector with three belts NOTE ALL VIEWS FROM INSIDE PSI COM 15 of 44 Assemble Left Wall Make certaln the places are in the correct positions
30. ove the bolt attaching left door track D 1L to F 7 profile With the wheels facing the inside line up so they roll inte the left door track As you roll the door along the track make certain it slides inside the B 5 door guide installed in step 10 2 Continue to rell door until it stops next to the bolt at the center Secure using the bolt you removed 10 40 Make sure the doors hana properly slide easily and look p straight IF you need to adjust 54 either one or both loosen the center bolts to either ralse or lower each door as needed Secure the center bolts when finished 10 54 Lining up holes in door install the D 5 door knobs using the Included screws MOTE VIEW FROM OUTSIDE 10 56 From the inside place the D 5 door guide bracket inte the channel in the base profile lining holes in bracket with Use two 5 3 screws to secure Repeat to install one bracket on each door NOTE VIEW FROM INSIDE 43 of 44 to Flatform Make certain the placas are in the correct positions before assembling A Carefully follow the order of assembly to ensure an easy installation Wear proper safety gear including work shoes gloves and goggles Prepare needed set screws as shown In step 1 14 NOTE Have the hex shaped indent facing up Screw in until itis flush with bottom of nut so it slides easily into bolt tracks After inserting into bolt track screw in until it holds in place
31. plete IF you have never assembled a greenhouse before make ita weekend project We recommend you take your time and read these instructions carefully to avold mistakes MOTE These instructions include helpful hints and important information needed to safely assemble and properly maintain the greenhouse Please read these instructions completely before you begin Before Starting Assembly 1 Make sure you have all the necessary parte Compare the contents of the five cartons with the List of Parts If any parts are missing or damaged or W you have any questions please contact Customer Service by phone at B77 373 5076 or by email at customersenioagirisww com before beginning assembly 2 Lay the parte out In one staging area The List of Parte has the corresponding step number referenced to each part so you can easily prepare for each step We recommend placing all parts in one staging area Lay out parte by size and shape Use the List of Farts to identify the part numbers for profiles and panels We have not labeled the parts with stickers to avoid removing them during assembly 5 Select a Location When selecting a site for your greenhouse a flat level surface i5 essential and if possible with proper water drainage and easy access to power and water necessary for greenhouse gardening Choose a sunny level position away from overhanging trees and power lines and protected from the wind as much as possible Tha location should away
32. rofile The profiles have different amounts of screws on the inside and outside bolt tracks The chart and illustration below show the set screw placement NOTE Instructions identify twelve set screws necessary for securing to ground in step 11 IMPORTANT When assembling base make sure the profiles are straight and flush against each other Secure profiles together and ensure corners are square The diagonal measurements on inside corners should be equal Secure corners to desired foundation until assembly is completed We recommend using a two by four platform IMPORTANT Position 2 and P 2B profiles at back of greenhouse Set Placement Code Set sorews used Insteps 1 44 and 1 48 8 Set screws used Insteps 2 through 10 Set sorews used instep 11 1 44 Make certain side profiles are straight and flush Adjust position of set screws in inner bolt track at front of profile to fit holes in B 5 connector Center connector over seam for maximum hold Secure using five bolts Kepeat on outer bolt track te install five remaining B 5 connectors at back and sides AS TT IMPORTANT One B 5 connector is installed on inside front Remaining B 5 connectors are installed on outside back and sides B 8 comer connectors are installed an inside and are flush Adjust position ofsete screws inner bolt track to fit holes in B amp connector Secure with four bolts Repeat until each corner is secure IMPO
33. rom outside position panel with extended ledge profile at outside top Install panel at slight angle sliding all the way inte profile Fit other end inte opposite profile F necessary apply slight pressure to bend panel and snap into place 8 Remove plastic film from both sides of second W 2 panel and repeat step amp 7B to install in second section from back left 8 85 Have one person stand outside the greenhouse to observe the position of the roof ridge while the other person installs the two B 9 braces The set screws should be in the correct position but Hf the roof is not completely straight loosen the set screws and adjust the brace to raise or lower the roof line Secure each with two bolts NOTE VIEWS FROM INSIDE The G 4 and G 4E trim plates snap into G 1 and G 2 gutter profiles to hold roof panels in place Working from outside begin at front corner Position G 4 trim plate over gutter and use handle of screw driver to tap into place Use three trim plates on each side Make sure the seams of the trim plates are flush with each other and to the C 1 connectors at the front There may bea slight gap at the rear C 1 connector depending on weather conditions Install Roof Vente Make certaln the places are the correct positions before assembling Carefully follow the order of assembly to ensure easy Installation Wear proper safety gear Including work shoes gloves and goggles o o O
34. s Screwdiver Power Drill recommended Make sure each corner ls square and then secure one corner with wood screws Move to the diagonal corner make sure It is square and then secure with wood screws you continue to secure the 2x4 wood platform continue to make certain the corners are square and the frame is level Secure wood platform every two feet with wood screws Make certain to tighten screws into the wood platform until they are flush with the surface MOTE The illustrations throughout the manual are shown without a foundation BS TWW CON Sof 44 List of Parte WARNING Profiles with cut edges and or drilled holes are sharp Use extreme caution when handling The greenhouse ls shipped five cartons These cartons are heavy Use care when lifting them Some parte have sharp edges Use extreme caution when handling Wear proper safety gear Including work shoes gloves and safety goggles Keep children and pete away until assembly ls complete Finish assembling the roof In one session Do not leave the roof unattended urrtil It completely assembled Place all like parte together a staging area Prepare for each step according to Instructions In this manual If any parts are missing or damaged contact Riverstone Customer Service before beginning assembly Customer Service 877 373 3078 or email customarservicegrisww com QTY Stepa List of Parts continued WARNING
35. se To avoid adjusting the placement after assembly prepare door frame using the exact measurements listed in these steps 5 1 4 Prepare two F 5 profiles 516 Fit B 2 connector onto profile and position so bottom Slide three set screws 1 of connector measures from bottom of profile inte bolt track and Secure each with two bolts position as shown 5 2B Prepare two F 6 profiles Slide set screws into both bolt tracks on mitered end of profile and ona bolt track on the other end single set screw will sit on the Inside when Installed Hand tighten each set screw to hold in place Working from inside front left corner remove plastic film from both sides of one W 1 panel Fit panel inte channel in base and corner profile placing side marked UV Fesistant facing outside IMPORTANT The panels expand and contract depending on the temperature To ensure proper placement use the 23 inch spacer included with the tools 6 368 Place 2 inch spacer on base next to 7 corner profile Fit panel into channel in F 1 profile and slide 1 profile against spacer to ensure proper placement MOTE Panels will nat fit completely to end of channels There will be some space to allow for temperature changes 5 30 Fit B 3 connector and secure with two amp 2C bolts c NOTE VIEW FROM INSIDE 5 3D Continue working from inside left corner place F 6 profile with mitered end next to corner and an
36. ure an easy installation Wear proper safety gear including work shoes gloves and goggles Prepare needed set screws as chown In step 1 1 MOTE Have the hex shaped indent facing up Screw in until itis flush with bottom of mut so it slides easily into bolt tracks After inserting into bolt track screw in until it holds in place 61A Prepare two F 7 corner profiles Slide set screws Into the same bolt track on each end of profile Tighten each set screw to hold in place 6 16 Prepare one F 2 profile Slide set screws Into both bolt tracks on each end of profile Tighten each set screw to hold in place 1 T nu L A Te 5 1C Prepare two F 3 profiles Slide set screws Inte both bolt tracks on straight end of F 3 profiles Tighten each set screw to hold in place WARNING The cut edge of F 3 profile is sharp Use extreme caution when handling 6 2 From insides add connector B 7 to each corner Secure each with two belts IMPORTANT Bolt track of F 6 front profile is lower than bolt track of G 1 gutter profile NOTE VIEWS FROM INSIDE 6 3 4 Continue working from inside Line up F 2 and F 3 profiles with F 1 profiles as shown Loosen set screws and adjust position to fit holes 1 connectors Make sure profiles are straight 6 38 Secure with bolt in each B 1 connector NOTE VIEW FROM INSIDE Gl 5 2 6 4 4 Work from outside to add 1 connectors in the sa
Download Pdf Manuals
Related Search