Custom Building Products TLSACRA1 Installation Guide
Contents
1. TileLab Sulfamic Acid Cleaner Care amp Maintenance TDS 139 1 Product Name TileLab Sulfamic Acid Cleaner 2 Manufacturer Custom Building Products Technical Services 10400 Pioneer Boulevard Unit 3 Santa Fe Springs CA 90670 Customer Support 800 272 8786 Technical Services 800 282 8786 Fax 800 200 7765 Email contactus cbpmail net custombuildingproducts com 3 Product Description Concentrated crystals that mix with water to make a mild safe to use acid cleaner Removes dried Portland cement grout haze and mortar residue from tile concrete and masonry Safe for use on colored grouts Removes hard water deposits efflorescence and also etches concrete Key Features e Removes grout haze and residue Uses Use on all colors of grout tile clay pavers concrete and masonry Limitations to the Product Do not use on marble or other polished stone May etch some glazed tile Packaging 1 Ib 450 gm tub 4 Technical Data Technical Properties Chart e pH of mixed solution is 2 3 e Complies with all Federal and SCAQMD Standards for VOC 5 Instructions Mixing Procedures Mix solution in a plastic container using clean warm water Don t mix in metal container Wear rubber gloves and eye protection For removal of light mineral deposits and Portland cement grout haze or mortar residue on unglazed quarry or glazed tile with colored grout mix 2 to 3 oz 57 to 85 gm with 1 gallon 3 78 L of water Mix 6 to 12 o2. in trash or recycle Health Precautions DANGER CORROSIVE HARMFUL IF SWALLOWED CAUSES EYE SKIN AND RESPIRATORY IRRITATION Wear skin and eye protection Do not breathe vapor or spray Contains Sulfamic Acid If in eyes flush with water for at least 15 minutes If on skin wash with soap and water If causing respiratory irritation move to fresh air If irritation persists seek medical attention If swallowed DO NOT induce vomiting seek medical attention KEEP OUT OF REACH OF CHILDREN Do not transfer contents to unlabeled containers Close container after each use Availability amp Cost Location _ Item Code Size Package j CUSTOM Care amp Maintenance TDS 139 TileLab Sulfamic Acid Cleaner 7 Product Warranty Custom Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase Custom s sole liability under this warranty shall be limited to the replacement of the product Some States countries or territories do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with Custom s printed instructions Custom makes no other war
3. ranties either expressed or implied This warranty gives you specific legal rights and you may have other rights that vary from state to state or from one country territory to another This warranty is not transferrable 8 Product Maintenance Properly installed product requires no special maintenance 9 Technical Services I nformation For technical assistance contact Custom Building Products 10 Filing System Additional product information is available from the manufacturer upon request DCUSTOM Published Date 7 29 2015 Care amp Maintenance TDS 139 TileLab Sulfamic Acid Cleaner Coverage SIZE MinCoverage Max Coverage 1 Gallon 3 78 L 300sq ft 28M2 DCUSTOM Published Date 7 29 2015
4. z 170 to 340 gm to 1 gallon 3 78 L of water for unglazed tile or masonry that has gray colored grout joints For etching concrete or heavy duty cleaning of old concrete mix a minimum of 12 oz 340 gm to 1 gallon 3 78 L of water Note Do not use on marble or other polished stone This product may etch some glazed tile Test solution on a small inconspicuous area before proceeding Don t allow product to contact metal fixtures Application of Product USE CHEMI CAL RESI STANT GLOVES such as nitrile when handling product Published Date 7 29 2015 Sulfamic Acid vieaner SOF grout haze and nesidus Read entire label before using Concrete and grout should be cured a minimum of 10 days and be clean Saturate unglazed tile concrete masonry or grout with clean water for one hour prior to application Apply solution to wet surface and scrub with a nylon bristle brush Work in small areas Flush with water immediately after brushing Do not use repeatedly or surface damage could occur For heavy concrete etching allow solution to sit for up to 30 minutes prior to flushing with clean water Cleaning of equipment Clean tools and hands with water before material dries Storage e Close container tightly after each use e Store in original container only e Store in and use in temperatures between 40 F 90 F 4 C and 32 C e Store in areas inaccessible to small children e Do not reuse empty container wrap and discard
Download Pdf Manuals
Related Search