Omega BL330S Use and Care Manual
Contents
1. As use of damaged or non recommended parts could result in a severe personal injury and or damage to the blender 2 Blades If the processing blades are stuck or difficult to turn DO NOT USE BLENDER Check by carefully turning the blades in a counterclockwise direction where the opposite edges are sharp Blades should turn freely 3 Container If the Eastman Tritan container is cracked DO NOT USE BLENDER further use could result in the container breakage during use 4 Blender Base Never immerse the blender base in water Unplug unit The housing can be cleaned with a damp cloth 5 Motor The motor is permanently lubricated and does not require any additional lubrication TROUBLESHOOTING Problem 1 Blender fails to start 2 Stopped 3 Ingredients do not mix properly Solution 1 Place container properly on the base 2 Check to ensure controls are clean and moving freely 3 Double check to ensure power cord is securely plugged into the electric outlet 4 Check to see if the circuit breaker has tripped or if the fuse for the electric out let has blown 1 Unplug blender and wait 5 minutes Plug the blender back in and resume op eration 1 Container is too full 2 Cutter unit blades are not sharp enough or are damaged 3 Solid pieces are bigger than 1 25mm cubes 4 Check the speed to create a fluid blend 5 Check to see if enough liquid has been added to the ingredients Mixture should b2. Close supervision is necessary when any appliance is used near children 8 Unplug from outlet when not in use before putting on or taking off parts and before cleaning 9 Avoid contact with moving parts especially blades 10 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner Return appliance to the nearest authorized service facility for examination repair electrical or mechanical adjustment or contact your Omega Distributor 11 Caution Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or damage to the blender If scraping folding etc is necessary turn off and unplug the blender and use a rubber spatula only 12 Warning Blades are sharp Handle carefully 13 To reduce the personal injury never place cutting blades on base without jar properly at tached 14 Screw on locking ring firmly Injury can result if moving blades accidentally be come exposed 15 Always operate blender with lid in place 16 When blending hot liquids place a hand towel over the cover Do not fill blender con tainer beyond 2 3 full Always begin process ing at the lowest speed setting Keep hands arms and face away from the feeder cup Opening to prevent possible burns 17 Do not use outdoors 18 Do not let cord hang over edge of table or counter or touch hot surfaces 19 Do not
3. Eat well drink well and live well with Omega www omegajuicers com BL330 SERIES BLENDER PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING YOUR BLENDER BLENDER SAFETY DANGER Electricity DANGER Risk of Electrical Schock A WARNING A Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock GENERAL Caution 4 DANGER Keep Hands Clear A WARNING amp Moving Parts Always cover the lid on the container when blending Do not put hands spoons or other utensils in container when blending Failure to follow these instructions can result in broken bones cuts or other injuries FAILURE TO ADHERE TO THESE WARNINGS CAN RESULT IN FIRE SERIOUS INJURY ELECTRICAL SCHOCK AND OR DEATH Technical Services For assistance or replacement parts call Technical Service 24 Hours a Day 7 Days a Week at Toll Free 1 877 368 2797 IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 Read all the instructions before using the blender 2 Plug into a grounded outlet 3 Do not remove ground 4 Do notuse an adapter 5 Do notuse an extension cord 6 To protect against risk of electrical shock do not put the blender in water or other lig uid 7
4. e fluid and free running at all times MAINTENANCE Inspect the blender and its various parts and replace as follows 1 Unplug the blender and remove the container from the base 2 Inspect the container blades for wear nicks and broken or loose blades Re place if necessary 1 Unplug the blender 2 Inspect the power cord insulation and power plug for cracks Refer to Techni cal Service for repair or replacement 1 Review the condition of the container assembly and Mushroom Clutch Set at Quarterly least every 90 days 1 Replace if necessary Replacement Parts For replacement parts call toll free 1 877 368 2797 Omega Products Inc 6291 Lyters Lane Harrisburg PA 17111 4523 U S A PH 717 561 1105 FAX 71 7 561 1298 OMEGA BL330 3 2011 RevA
5. leave blender unattended while it is operating 20 The use of attachments not approved by Omega may cause injuries 21 The capacity can be substantially less than normal with thick mixtures 22 Inspect the container assembly daily Do not use a broken chipped or cracked container Check cutter for wear nicks or broken blades 23 This appliance is intended for short period of operation with a average rated op erating time of approximately 3 minutes BLENDER OPERATION To operate the blender proceed as follows 1 Forthe first time user wash the container assembly including the lid before using it Refer to Cleaning Instruction Do not put the container assembly 8 blender base assembly in the dishwasher 2 Place the blender on a dry clean level surface and press OFF 3 Place the container onto the motor base Make sure it rests securely on the base 4 Plug the blender into an electric outlet 5 Place the ingredients into the container 4 Place the lid and feeder cap tightly on the container 7 Select desired speed and time by rotating dials 8 Press ON PROFESSIONAL BLENDER TIP 1 Processing hot liguid OAlways cover the lid and feeder cap before blending hot liguid or mixtures Ouse the feeder cap to add liquids to the container while the unit is running ONever stand with your face directly over the container when you are putting ingredient through the feeder cap 2 Blending Icy mixtures OStep
6. s for blending ice Pour in liquid and then add ice Place the lid Set to desired speed Chunks of frozen fruit can be added to milk or fruit juice to produce a sherbet or slush Use the feeder cap to add liquids or ingredients to the container while the unit is running CLEANING INSTRUCTION Blender container parts are corrosion resistant sanitary and easily cleaned Do not put the container assembly amp blender base assembly in the dishwasher 1 Before first use and after every use separate container parts from the base 2 Add cleaning solution to the container Use washing solution of tepid water less than 115 F 46 C and a non sudsing detergent Use the recommended amount of detergent 3 Scrub and flush out the container interior lid and feeder cap to remove food residue Empty container 4 Fill container 1 4 full with fresh washing solution and place it on the base 5 Replace the lid on the container and run the blender on high speed for 2 minutes 6 Repeat step 4 using clean rinse water 95 F 35 C 7 Wipe down the container feeder cap and lid with a soft cloth or sponge dampened with fresh washing solution 8 Wipe the exterior of the base with a damp cloth or sponge The base contains electrical components do not immerse use a high pressure washer or use a dishwasher to clean the base CARING TIPS To care for your blender please read the tips as follows 1 Periodically check all parts before reassembly
Download Pdf Manuals
Related Search