Powr-Flite PS35E Use and Care Manual
Contents
1. COMMERCIAL FLOOR CARE EQUIPMENT Commercial Spotter Model number PS35 OPERATING INSTRUCTIONS COMMERCIAL AND HOUSEHOLD SPOTTER EXTRACTOR CONGRATULATIONS YOU HAVE JUST ACQUIRED A HIGH QUALITY COMMERCIAL SPOTTER PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING YOUR NEW COMMERCIAL SPOTTER KEEP MANUAL ON HAND FOR FURTHER REFERENCES Save These Instructions X8721 6 2004 IMPORTANT SAFETY INSTRUCTIONS When using a commercial spotter basic precautions should be followed including the following Read all instructions before using this commercial spotter SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE To reduce risk of fire electric shock or injury Do not use outdoors or on wet surfaces Do not leave commercial spotter unattended when plugged in Turn off the switch and unplug the electrical cord when not in use and before servicing Do not allow to be used as a toy Close attention is necessary when used near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If commercial spotter is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center before using Do not pull or carry by cord use cord as a handle close a door on cord or pull a cord around sharp edges or corners Do not run commercial spotter over cord Keep cord away from heated surfaces Do2. BRAIDED 19 X9060 SCREEN VACUUM MOTOR 5 X8212 WASHER 1 4 MED SPLIT LOCK ZINC 20 1942 IE MOTOR VACUUM IMPERIAL ELECTRIC 6 X8291 CAP SVREW 1 4 20 X 5 1 2 ZINC 21 7 2001 1 1 2 WIRE REINFORCED HOSE 7 PD8 STRAIN RELIEF 1 2 NPT 22 X9045 MOUNTING POST VACUUM MOTOR 8 X9048 SWITCH ROCKER SPOTTER 23 PC10 MALE QUICK DISCONNECT 9 M1408 POWER CORD 18 3 X 15 24 X8270 SCREW 10 24 X 1 2 PHILLIPS TRUSS HEAD 10 7DLO003 CLAMP 1 4 WORM GEAR STAINLESS STEEL 25 X8214 NUT SPEED 1 4 20 U TYPE CLIP 11 PX214 FITTING NYLON 90 DEG ELBOW 26 X8293 WASHER NYLON 50 ID X 75 OD X 13 THK 12 PX204 MOUNT FLOJET PUMP SPOTTER Not Illustrated 13 FJ5082 PUMP OSCILLATING FLOJET X8284 SCREW 8 32 X 3 8 PHIL PANTCS 14 71817A HOSE 1 4 BRAIDED X8008N NUT 1 2 CONDUIT 15 X8271 NUT 10 24 W NYLON INSERT PX215 CLAMP 2 1 2 WORM GEAR S S X8497B SWITCH LABEL 2 5 X 1 5 COMMERCIAL FLOOR CARE EQUIPMENT 3101 Wichita Court Fort Worth Texas 76140 1710 Call Toll Free 800 880 2913 e Fax 817 551 0719
3. not use extension cords or outlets with inadequate current carrying capacity Turn off all controls before unplugging Do not handle plug or commercial spotter with wet hands Do not put any objects into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce airflow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Store your commercial spotter indoors in a cool dry area Do not unplug by pulling on cord To unplug grasp the plug NOT THE CORD THESE MODELS ARE GROUNDED CONNECT TO A PROPERLY GROUNDED OUTLET ONLY SEE GROUNDING INSTRUCTIONS GROUNDING INSTRUCTIONS GROUNDING OUTLET GROUNDED OUTLET BOX GROUNDING A 2 PIN This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for elec tric current to reduce the risk of shock This appliance is eguipped with a cord having an eguipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of
4. the eguipment grounding conductor can result in a risk of electric shock Check with a gualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the appliance if the plug will not fit the outlet have a proper outlet installed by a gualified electrician This appliance is for use on a normal 120 volt circuit and has a grounded plug that looks like the plug illustrated in sketch A Note In Canada the use of a temporary adapter is not permitted by the Canadian Electrical Code Operating Instructions for PS35 Commercial Spotter WHEN THE MACHINE IS DELIVERED Check the carton carefully for signs of rough han dling Remove the machine from the carton If the machine is damaged notify the carrier immediately and reguest an inspection Be sure to keep the car ton packing inserts packing lists and carrier receipt until the inspector has verified your claim Liability ceases when the shipment is picked up by the carrier but our customer service staff will be glad to furnish any information needed in connec tion with the claim and will expedite the repair of the machine BEFORE USING THE MACHINE Read the manual carefully and completely before attempting to operate the unit This manual has important information for the use and safe operation of this machine Keep this manual handy at all times The commercial spotter will provide years of satisf
5. Do not use cleaning chemicals in this machine except those recommended for commercial extraction equipment The use of any chemical with abrasive additives voids the warranty Do not break off or pull out the ground prong on the plug Do not attempt repair on a warranted machine unless instructions to perform it by an authorized shop are obtained from the factory Do not use any replacement parts except those specified on the parts list Proper performance of the machine could be affected if substitutions are made Use defoamer at all times to prevent damaging the vacuum motor Do not use water in excess of 140 62 Failure to comply with the above warning instructions will void the warranty Operating Instructions for PS35 Commercial Spotter Filling the Spotter Disconnect the solution and recovery tanks Add water and or chemi cals to the lower solution tank The tank will hold up to 3 5 gallons Operating the Spotter A Attach the solution feed line to the guick disconnect at the bottom of the machine Disconnect tanks B Attach the vacuum hose to the vacuum inlet handle above the recovery tank lid Attach vacuum hose wy C Turn the 3 way switch to use either the pump and vacuum or the vacuum alone Allow approximately 30 seconds for the pump to prime D Use the hand tool to spray and recover the solution E The float shut off will disable the suction of the unit when the recovery tank is
6. Y 28 PX213 FITTING 1 4 NPTM X 1 4 HOSE BARB T7 X9064 GASKET SOLUTION TANK 29 X9072 CORD HOOK 8 X9079 GASKET DONUT 3 8 THICK 30 X8270 SCREW 10 24 X 1 2 9 PX46 NUT LOCK DIE CAST 1 1 2 31 X9069 END LOOP STAINLESS STEEL W TWO HOLES 10 PX14A DAMP VALVE GASKET 1 1 2 THIN 32 X9068 12 STAINLESS STEEL JACK CHAIN 11 X8278 SCREW 8 32 X 1 2 PAN HEAD PHILLIPS 33 X8849 SCREW 8 18 X 1 2 PHILLIPS PAN 12 X9073 PLUG 7 8 X 1 1 16 SNAP TITE 34 X9065 SCREW 1 4 20 X 1 SHCS 13 X9076 BULKHEAD 1 1 2 MPT X 1 1 2 35 SP101BLU SOLUTION TANK 14 X9082 1 1 2 PVC SCHEDULE 40 PIPE 36 SP102BLU RECOVERY TANK 15 X9062 FLOAT RING VACUUM SHUT OFF 37 72173A CLIP SPRING BLACK VINYL COATED 16 PX103AG GASKET LID 6 O D X 4 6 I D 38 PX209 FILTER FOAM 1 1 2 O D X 1 2 THICK 17 PX103A LID 4 CLEAR W BLACK RING 39 7DL003 CLAMP 1 4 WORM GEAR STAINLESS STEEL 18 X9087 WASHER 6 X 5 8 SAE FLAT 55 Not Illustrated 19 X9088 SCREW 8 18 X 1 2 PAN HD PHIL SS X9058 HOSE ASSEMBLY STRETCH 10 FT 20 X9061 SHUT OFF DISK AA195 HAND TOOL DETAILER ASSEMBLY 1 1 2 21 X8295 SCREW 8 X 3 4 PHILLIPS FLAT TS X8962 LABEL 22 PC66 FITTING 1 8 NPTM X 1 4 HOSE BARB Motor Assembly ref order description ref order description 1 X9046 BASE PLATE WELDMENT SPOTTER 16 PC66 FITTING 1 8 NPTM X 1 4 HOSE BARB 2 7CM004 WASHER 3 8 FLAT STAINLESS STEEL 17 X8237 NUT 1 4 20 LOCK NYLON INSERT 3 7ATO06 BARB ELBOW 90 1 4 1 8 BRASS 18 X9078 VACUUM MOTOR GASKET 4 71817A HOSE 1 4
7. actory service if operated and maintained according to recommendations in the manual WARRANTY To protect your investment promptly fill in the required information on the warranty card included with the unit Then mail the card back GENERAL PRECAUTIONS Follow these guidelines to ensure operator safety and to maintain equipment in running order m Make sure the machine is plugged into an electrical outlet with the same voltage rating as shown on the nameplate of the machine Do not attempt to plug a 115 volt machine into a 230 volt outlet or a 230 volt machine into a 115 volt outlet Disconnect the power cord from the outlet before attempting maintenance or repair work Do not leave machine connected to an electrical outlet when unattended Never pull the machine by the cord or yank the cord from the receptacle Replace a damaged cord immediately If an extension cord is necessary use a three conductor grounding cord 12 gauge wire or heavier to prevent motor burnout and over heating of wires To avoid electric shock do not expose to rain Store indoors To avoid fire do not use machine in environ ments where combustible liquids vapors or dust concentrations are present WARNING Do not expose the machine to freezing tempera tures Do not use the machine for totally dry vacuum ing This machine is not fitted with a fine dust filter Do not use citrus based cleaners in this machine
8. full The operator will notice a distinctive change in the sound of the vacuum motor when the shut off is activated Empty the recovery tank to resume cleaning Attach solution hose Emptying the Recovery Tank Disconnect the solution line and vacuum hose 3 way switch Unlatch the recovery tank from the base of the unit and remove Remove the drain plug Drain tank over suitable outlet for wastewater Rinse tank after each use mgom Drain plug Basic Troubleshooting A If the pump does not prime depress the lever on the hand tool to release the air lock B If solution flow is reduced or spray is weak 1 Check for low solution level in the solution tank 2 Check the screen on the hose in the solution tank for blockage 3 Check the spray jet in the hand tool for blockage If suction is low 1 Check the recovery tank to see if it is full 2 Check for blockage in the hand tool or the hose 3 Add defoamer to recovery tank Parts Diagram Parts List ref order description ref order description 1 X9047 CASTER SWIVEL 45MM 23 72115A WASHER 5 8 X 1 3 16 NEOPRENE BOND 2 7BS003 SCREW 1 4 20 X 1 2 PHIL STAINLESS STEEL 24 7AJ004 ANCHOR CONECTOR 1 8 3 X8212 WASHER 1 4 MED SPLIT LOCK ZINC 25 7ATO06 FITTING ELBOW 90 DEGREE 1 4 1 8 4 X8262 SCREW 8 32 X 1 4 THPH BLACK 26 71817A HOSE 1 4 BRAIDED 5 X9059 LATCH OVER CENTER W KEEPER 27 PX30 FILTER MESH SCREEN 6 X8990 HANDLE WHEEL ASSEMBL
Download Pdf Manuals
Related Search