Bissell BG477 Use and Care Manual
Contents
1. surfaces The brush pressure is continuously adjustable by means of the adjusting button item 1 11 Step 1 2 new brushes for all even floors Step 3 4 new brushes for wet leaves sand uneven floors e g exposed aggregate concrete Step 5 8 older brushes for readjustment of the worn brush parts Please ensure that the brushes rest on the floor with light pressure only Deeper adjustments do not bring about better cleaning results and may increase the wear Push the sweeping machine with normal speed and lift the sliding handle a little bit The protruding circular brushes will sweep all the corners too To sweep over small steps 2 3 cm slightly press down the sliding handle To clean edges push knob item 1 22 Storage Fig 1 The best way to store the Turbo sweeping machine is in the vertical position and can be best accomplished by placing the unit on the backside of the bin or by suspending it with the sliding frame top side of the machine in direction to the wall Emptying To open the dirt bin pull the bin handle item 6 05 upward After removing and emptying the bin replace it and lock it by pushing down the bin handle Maintenance You chose a product that is easy to maintain Disc brushes roller brush and drive can all be cleaned with a rag and water Do not submerge any of these parts in water Never use a pressure washer for cleaning All of the bearings are dust protected and when used and maintained correct2. the circular brushes into the pivot housing Then fit the clutch item 3 10 into the tooth sleeve item 3 02 and insert them into the circular brush Lastly insert and engage the oblique wheel and you re ready to go For the replacement of the sweeping roll press the stop bracket of the brush holder item 8 15 Ensure that the bristles are not pinched laterally and that the stop bracket is in its correct starting position again Guarantee 4 year warranty against wear for the disc brushes 2 year warranty for all other parts referring to the EU law excludes wear What should be done when the unit does not run smoothly 1 Check the sweeping pressure adjustment 2 Clean the unit and remove spooled laces etc 3 Spray the gear parts with special spray 4 Check the sense of rotation of the circular brushes after repair
3. ly this machine is maintenance free Please clean wash the dust filters from time to time WARNING Built up dirt and spooled laces etc behind the brushholder Pos 8 15 can impede the manoeuvrability of the sweeping machine and adversely effect its operation Maintaining your sweeping machine will ensure its operation and long life In order to guarantee an easy and wear resistant operation the brush drives Pos 4 03 3 0 should be sprayed with the original lubricant spray from time to time Do not use other oils or grease Exchanging Brushes The brushes are made of highly wear resistant material After using them many years it may be necessary to replace them We recommend to replace the complete brush set at the same time For the replacement of the circular brushes set the height adjustment item 1 11 to step 8 and place the machine vertically Then pull the oblique wheel item 4L R strongly and remove it together with the shaft from the machine Next strongly pull off the circular brushes item 2L R together with the tooth sleeve and the clutch item 3L R from the pivot housing Attention The markings for L and R are applied on the inside of the frame item 1 12 on the helical gears and on the clutches item 3 10 The circular brushes are marked on the bottom with L or R depending on the direction of the bristles Ensure that the correct side of assembly is used The assembly is carried out in reverse order Fit
4. o Bissell BigGreen Commercial BG477 Instruction Manual bo 8a Roana Bissell BigGreen Commercial Sales amp Service 1 800 242 1378 GB USA Dear Costumers We are happy that you chose a quality product TheBG 477 is an especially efficient hand sweeping machine that is simple to operate and that can be used for all even and hard surfaces The unique Turbo sweeping system with circular brushes and sweeping roll guarantees double cleanliness The flatly operating circular brushes collect all kinds of road dirt from fine dust to wet leaves empty cans and even heavy garbage The sweeping roll collects fine dust and in addition ensures the optimal overhead filling of the dirt container In order to guarantee a long service life of your sweeping machine the following operating instructions must be observed Assembly of the sliding handle Fold the the handle fitting item 7 13 forward to an angle of 45 and pull it Push the catch spring of the sliding handle item 7 12 and connect the sliding handle item 7 11 with the handle fittings item 7 13 by engaging the catch spring To fit handle to the sweeper frame Pos 1 12 fold the handle forward to an angle of 45 towards the front brushes the handle holder will snap into position To fix the handle move the handle back to normal sweeping position Operation Adjustment The 477 sweeping machine is factory preset for even
Download Pdf Manuals
Related Search