Shark NV360K Use and Care Manual
Contents
1. l r f f 3 NV360K Owner s Guide IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WHEN USING AN ELECTRICAL APPLIANCE BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK NAVIGATOR LIFT AWAY DELUXE POLARIZED PLUG To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other As a safety feature this plug will fit into a polarized outlet only one way If the plug does not fit fully into the outlet reverse the plug If it still does not fit contact a qualified electrician DO NOT force into outlet or try to modify to fit A WARNING To reduce the risk of electric shock or injury do not use outdoors or on wet surfaces WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY GENERAL ELECTRICAL SAFETY 1 Unplug from electrical outlet when not in use and before servicing 2 DO NOT use vacuum with a damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to EURO PRO Operating LLC for examination repair or adjustment 3 DO NOT pull or carry vacuum by the cord 4 DO NOT unplug by pulling on cord to unplug grasp the plug not the cord 5 DO NOT handle plug or appliance with wet hands DO NOT run the vacuum over the power cord DO NOT use the cord as a handle DO NOT2. 1 Undo the latches on the sides of the dust cup by lifting them up and outwards to remove the dust cup from the motor base Fig 18 Hold the dust cup over a trash receptacle and press the bottom door release button Fig 19 Tap gently to empty contents Press the door shut again until it clicks If needed turn the dust cup upside down over the trash receptacle and press the top door release button Fig 20 Tap gently to remove contents Use a dry cloth or paper towel to remove debris stuck to the screen filter inside the dust cup Press the door shut again until it clicks Replace the dust cup on top of the motor base Hook the two latches onto the tabs on the sides of the dust cup and push down to lock MAINTENANCE SCHEDULE Empty each time you vacuum Rinse and air dry every 3 months under normal use Rinse and air dry every 3 months under normal use Clean once every 2 years or as needed Ay IMPORTANT Loss of Suction may occur if foam filters are not cleaned every 3 months Rinse and allow to air dry completely Also tap loose dirt off filter between washes as needed Foam filters may appear dirty after use this is normal Pre Motor Foam Filter Felt Filter Post Motor HEPA Filter CLEANING THE PRE MOTOR FILTERS 1 2 3 Remove the dust cup Pull the 2 filters out from the top of the motor base Fig 21 Rinse the filters thoroughly in lukewarm water until the water runs clear
3. BRUSH This unique tool was engineered for fast and easy removal of pet hair and ground in dirt from carpeted stairs and upholstery Fig 3 ACCESSORY HOLDER Designed to hold the crevice tool and dusting brush For quick access to tools when vacuuming and cleaning around the house Fig 4 APPLIANCE WAND Removes dust from underneath appliances Fig 5 Your new Shark Navigator Lift Away Deluxe vacuum cleaner can easily be configured into different cleaning modes to meet all your cleaning needs upright vacuum and portable Lift Away both with constant suction power MODES 7 1 UPRIGHT VAC 2 PORTABLE LIFT AWAY Upright vacuuming floors and carpets Fig 6 Take the Lift Away with you around the house to clean hard to reach places Fig 7 Mode 1 Upright Vac 4d To reduce the risk of electric shock unplug the unit before assembling adding or removing attachments or converting modes 4s WARNING The On Off switch is on the top of the Lift Away canister Always ensure the power is OFF O position before plugging and unplugging Upper Cord Storage Wrap TO ASSEMBLE 5 Push the handle b onto the top of the extension wand until you hear it click into place Fig 10 6 Insert the end of the stretch hose c into the connector on the back of the Lift Away canister Fig 10 7 Store the dusting brush d and the crevice tool e on the mounts of the accessory holder Fig 10 1 Place t
4. do Not put the filter in the washing machine or dishwasher NOTE The material in the filter will discolor over time This is NORMAL and will not affect the performance of the filter Squeeze out excess water and let air dry for at least 24 hours before replacing Do not use a hair dryer or other heating methods to dry Place the felt filter in first then the foam filter Replace the dust cup Maintenance cont d 4 y l i in San fas n 14 a A Fig 24 CLEANING THE POST MOTOR HEPA FILTER 1 Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum Fig 22 Take out the HEPA filter by pulling it straight out Turn the filter over so that the dirty side is on the bottom and vigorously tap it clean against a garbage can to remove any dust Fig 23 4 Wash the filter under the tap using lukewarm water with the dirty side face down until the water runs clear Fig 24 Do Not put the filter in the washing machine or dishwasher NOTE The material in the filter will discolor over time This is NORMAL and will not affect the performance of the filter 5 Allow the filter to air dry for 24 hours Do not use a hair dryer or other heating methods to dry 6 Once the HEPA filter is dry replace it back into the vacuum 7 Replace the cover by inserting the two tabs into the holes at the top and then swinging the cover down until it clicks in
5. 10 days of purchase You will be asked to provide the store name date of purchase and model number along with your name and address The registration will enable us to contact you in the unlikely event of a product safety notification By registering you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions www sharkclean com
6. FELY Ad To reduce the risk of electric shock unplug the unit 1 Convert your vacuum back to upright vac mode before performing any cleaning maintenance or 2 Rotate the upper quick cord release to its upright troubleshooting checks position and coil the power cord loosely around Ad Reassemble all parts securely before operating the two clips Clip the plug onto the cord to secure vacuum Fig 17 l amp do NoT operate the vacuum without the filters 3 Store the dusting brush and the crevice tool on the and dust cup in place mounts on the accessory holder A DO NOT operate the vacuum with WET filters 4 Store your vacuum cleaner safely in a cool dry area where it will not be a hazard will not get damaged 4 IMPORTANT Make sure all filters are completely and will not cause damage to anyone or anything dry before inserting back into vacuum NOTE Empty dust cup after cleaning and prior 4 WARNING Never insert sharp objects into any to storing See Maintenance section for opening to clear an obstruction instructions amp important Damages caused while clearing or attempting to clear blockages are not covered under your product s limited warranty Maintenance 2 COMPONENT Dust Cup Pre Motor Foam Filter Pre Motor Felt Filter Post Motor HEPA Filter Fig 20 EMPTYING THE DUST CUP The dust cup needs to be emptied each time you vacuum and periodically during cleaning when the dust cup appears full
7. cement are specifically excluded from warranty This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal implied and or conventional warranties The responsibility of EURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province IMPORTANT Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach a tag to item before packing including your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with the item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice a Product Registration Please visit www sharkclean com or call 1 800 798 7398 to register your new Shark product within ten
8. close a door on the cord DO NOT pull cord around sharp corners The use of an extension cord is not recommended io 9 N g 10 DO NOT leave appliance when plugged in 11 Keep cord away from heated surfaces 12 Turn off all controls before plugging or unplugging vacuum cleaner 13 Always turn off this appliance before connecting or disconnecting motorized nozzle 14 Store your appliance with the power cord secured around the two cord holders as shown in the storage instructions HOSE ATTACHMENTS 1 DO NOT use if air flow is restricted if the air paths the hose or the accessories become blocked turn the vacuum cleaner off Remove all obstructions before you turn on the unit again 2 Keep the end of the hose and accessory openings away from face and body 3 Keep cleaning tools and hose suction openings away from hair face fingers uncovered feet or loose clothing 4 Only use manufacturer s recommended attachments GENERAL USE 1 Use only as described in this manual 2 DO NOT put any objects into openings DO NOT use with any opening blocked keep free of dust lint hair and anything that may reduce air flow 3 Keep your work area well lit 4 Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers 5 DO NOT place vacuum on unstable surfaces such as chairs or tables 6 DO NOT allow young children to operate the vacuum or use as a toy Close a
9. ent this from happening check potential blockage areas after heavy use or if you detect a loss of suction or poor cleaning performance 1 Dust Cup Dust cup may be full Empty dust cup 2 Pre Motor amp Post Motor Filters e Pre motor filters require washing every 3 months for optimum performance The post motor HEPA filter needs to be washed every 2 years e Ensure that all the filters are clean 3 Accessories e Check intake openings Extension Wand Dusting Brush Crevice Tool Power Brush Appliance Wand 4 Hose and Connections to Vacuum e Detach the stretch hose from the back of the portable Lift Away canister by squeezing the tabs together and pulling up Fig 28 Straighten out the hose and look inside for blockages Remove the dust cup and extension wand and separate the portable Lift Away canister from the motorized floor brush Look in all 4 openings for any blockages Fig 29 5 Motorized Floor Brush Side suction models Detach the hose on the motorized floor brush at the top by squeezing the tabs together and pulling out and at the bottom by pulling out the connector Inspect inside the 3 holes Fig 30 EURO PRO FIVE YEAR 5 LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of five 5 years from the date of purchase when utilized for norma household use subject to the following conditions excl
10. he floor nozzle on a level surface 2 Align the tube of the floor nozzle with the tube on the Lift Away canister and lower until you hear the two pieces click into place Fig 8 When attaching the motorized floor brush ensure that the latching mechanism is fully locked in place to ensure electrical connection has been made 3 Attach the end of the extension wand to the tube on the back of the Lift Away canister until it clicks into place Fig 9 4 Slide the accessory holder a positioned opposite the upper cord wrap over the extension wand Align the tab with the groove and push down Fig 10 j Release suction Suction Release Collar for easier push amp pull on high pile carpets and area Tugs TO USE 1 Rotate the cord release to quickly release the power cord Secure the power cord in the cord hook Brush Roll ON Bare Floor O OFF Press the On Off switch a to the I position to vacuum bare floors straight suction only or to the II position to engage the motorized floor brush for vacuuming carpets and rugs Fig 11 4 IMPORTANT The motorized brush indicator light b will illuminate green when motorized floor brush is on or red if there is a blockage or jam Fig 11 This feature is designed to protect your Lifetime Belt that powers your motorized floor brush See Checking for Blockages on page 15 Fig 12 Gently press the floor nozzle down with
11. he house with the 2 Press the handle release button a and pull the other hand Fig 15 handle up or press the extension wand release button b and pull the extension wand up Fig 14 a Above Floor Cleaning Lo Release suction when dusting delicate objects furniture or draperies Suction Release Collar CLEAN ABOVE THE FLOOR IN UPRIGHT VAC OR 4 Press the On Off switch to the position to turn PORTABLE LIFT AWAY MODE the vacuum on for above floor cleaning 1 Press the handle release button and pull the A IMPORTANT Ensure vacuum is in upright handle up or press the extension wand release position Do not use position II when cleaning button and pull the extension wand up above the floor in the upright vac mode as this 2 Attach desired accessory onto the end of either the will engage the motorized floor brush The extension wand or the handle Fig 16 rotating brush may damage your floor if run for a i rolonged period of time in o 3 Your vacuum has tremendous suction Pee P DES Bea power Adjust the amount of suction with the suction release on the handle Open the valve a by rotating the collar 90 counterclockwise for low suction when doing light jobs such as drapes or fine surfaces Close the valve a by rotating the collar clockwise 90 for high suction and when using the hand held power brush Fig 16 Storage and Maintenance Lower Cord Storage Clip STORE YOUR VACUUM SA
12. rfaces use only on dry surfaces 10 Use extra care when cleaning on stairs SAVE THESE INSTRUCTIONS This manual covers model numbers NV360K 26 TECHNICAL SPECIFICATIONS Voltage 120V 60Hz Watts 1200W Amps 10A Euro Pro Shark and Navigator are trademarks of Euro Pro Operating LLC All other brand Thank you for purchasing the Shark Navigator Lift Away Deluxe Contents Getting Started Mode 1 Upright Vac Mode 2 Portable Lift Away Above Floor Cleaning Storage Maintenance Emptying the Dust Cup Cleaning the Pre Motor Filters Cleaning the Post Motor HEPA Filter Cleaning the Pet Power Brush Cleaning the Motorized Floor Brush Checking for Blockages Troubleshooting Guide Ordering Parts Warranty amp Product Registration 10 11 12 13 13 13 14 14 14 15 16 17 19 Getting Started FIRST THING S FIRST YOU NEED TO KNOW WHAT S IN THE BOX YOU JUST OPENED Handle with Stretch Hose Accessory Holder Extension Wand Portable Lift Away Motorized Floor Brush Dusting Brush Crevice Tool Power Brush Appliance Wand a w mT Mm Oo an amp Fig 1 Fig 2 ACCESSORIES CREVICE TOOL Reach deep into narrow spaces and clean between cushions under radiators and baseboards and in hard to reach crevices and corners Fig 1 DUSTING BRUSH Dust shelves lamp shades window blinds books furniture and other upholstered household items Fig 2 POWER
13. to place a CLEANING THE POWER BRUSH 1 Slide the locking latch a forward and gently tilt brush housing upward to remove Fig 25 2 Carefully remove any blockage or debris and cut away any build up of hair or string wrapped around the rotating bristle brush with scissor 3 Toreassemble insert the tabs on the front edge of the bottom cover into the matching holes in the top half and tilt it back down until it clicks into place Fig 26 Fig 26 Fig 27 CLEANING THE MOTORIZED FLOOR BRUSH When your motorized floor brush needs cleaning or locks onto an object it automatically shuts down to prevent damage to your lifetime belt The indicator light will illuminate red warning you to turn off the vacuum and clear blockage immediately The light will reset itself once blockage has been cleared and power has been cycled on off or vacuum has been locked in the upright position 1 Detach the motorized floor brush from the portable Lift Away canister 2 Inspect the opening underneath and the rotating brush If a build up of debris is present remove it Carefully cut anything wound around the rotating brush with scissors Avoid damaging or cutting the bristles Fig 27 se Make sure you are working in a well lit area and use a flashlight to help a search for blockages E Ei pr 3 Fig 28 CHECKING FOR BLOCKAGES Blockages may cause your vacuum to overheat and shut down To prev
14. ttention is necessary when used by or near children 7 DO NOT use vacuum cleaner if it has been dropped damaged left outdoors or submerged in water Return to EURO PRO Operating LLC for examination repair or adjustment 8 DO NOT use without dust cup and or filters in place DUST CUP FILTERS ACCESSORIES Before turning on the vacuum 1 Make sure that all filters are thoroughly dry after routine cleaning Make sure that dust cup and all filters are in place after routine maintenance Make sure accessories are free of blockages Only use filters and accessories provided by EURO PRO Operating LLC Failure to do so will void the warranty GENERAL CLEANING DO NOT pick up large sized objects DO NOT pick up hard or sharp objects such as glass nails screws or coins that could damage the vacuum cleaner DO NOT pick up smoking or burning objects such as hot coals cigarette butts or matches DO NOT pick up flammable or combustible materials such as lighter fluid gasoline or kerosene or use vacuum in areas where they may be present DO NOT pick up toxic solutions such as chlorine bleach ammonia or drain cleaner DO NOT use in an enclosed space where vapors are present from paint paint thinner moth proofing substances flammable dust or other explosive or toxic materials DO NOT vacuum up any liquids DO NOT immerse vacuum cleaner in water or other liquids DO NOT use outdoors or on wet su
15. usions and exceptions The liability of EURO PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This Limited Warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alteration to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO lt Operating LLC If your appliance fails to operate properly while in use under normal household conditions within the warranty period you may return the complete appliance and accessories with proof of purchase and date freight prepaid For customer service support call 1 800 798 7398 or visit our website at www sharkclean com If the appliance is found by EURO PRO Operating LLC to be defective in EURO PRO Operating LLC s sole discretion we will repair or replace it free of charge Proof of purchase date and a check made payable to EURO PRO Operating LLC in the amount of 19 95 to cover the cost of return shipping and handling must be included Non durable parts including without limitation filters brushes and electrical parts which normally require repla
16. your foot while you grasp the handle and tilt it back towards you Fig 12 NOTE The rotating brush on the motorized floor brush will not spin unless the nozzle is flat against the floor and the handle is tilted back Due to the huge suction power of this vacuum it may become necessary at times to adjust the suction release c on the handle Fig 11 If the vacuum seems difficult to push or pull or if it is lifting up area rugs adjust the suction release by rotating the collar 90 counterclockwise to open the valve Rotate the collar clockwise to close the valve when you need high suction and for vacuuming floors Empty dust cup after vacuuming and periodically during use when it appears full See Maintenance section for instructions When you are finished vacuuming turn the vacuum off Mode 2 Portable Lift Away Y You can carry your vacuum cleaner in both modes by the carry handle located on top of the dust cup PORTABLE LIFT AWAY 3 Attach desired accessory onto the end of either 1 Separate the portable Lift Away canister from the extension wand or the handle the floor nozzle by pressing the red release 4 Press the On Off switch to the I position to button a on the side of the canister Gently turn the vacuum on for above floor cleaning and hold the nozzle to the floor with your foot and hold the handle in one hand while you carry the pull the canister up Fig 13 portable Lift Away around t
Download Pdf Manuals
Related Search