Metro MDV2TAC Use and Care Manual
Contents
1. THROUGH CARTRIDGE SEAL 5 VACUUM IN THE AREA OF THE PRINTER CORONA WITHOUT MAKING CONTACT WITH SAME 6 VACUUM AS CLOSE AS POSSIBLE WITHOUT TOUCHING COMPONENTS 7 VACUUMING WITH METRO DATA VAC 2 MODEL MDV 2 OR METRO DATA VAC 3 MODEL MDV 3 UTILIZING OPTIONAL TONER STARTER KITS MODEL TSK 1 INSURES ENVIRONMENTAL SAFETY METRO DATA VAC TRAPS AND REMOVES POLLUTANTS RECYCLES THE AIR WITHOUT HARMFUL CONTAMINANTS EXPELLING INTO THE ATMOSPHERE 8 FINALLY METRO DATA VAC IS DESIGNED TO PROVIDE MORE ACCURATE CLEANING DATA VAC SAVES COSTLY SERVICE CALLS AND DOWNTIME DATA VAC THE NECESSARY ACCESSORY 1 DATA VAC Computer Maintenance Guide INSTRUCTIONS FOR USE OF TONER STARTER KIT AND TONER BAGS FILTERS OPEN CLAMPS REMOVE FRONT DOME FROM METRO DATA VAC 2 MODEL MDV 2 METRO DATA VAC 3 MODEL MDV 3 REMOVE PAPER DISPOSABLE BAG PERMANENT CLOTH BAG AND FOAM FILTER SECURELY INSERT SPECIAL GREEN MICRO FILTER IN PLAGE PLACE PERMANENT CLOTH BAG BACK INTO UNIT FIT RUBBER DIAPHRAGM OF SPECIAL TONER FILTER BAG ONTO PLASTIC TUBE LOCATED INSIDE FRONT DOME REPLACE FRONT DOME ONTO DATA VAC AND SECURE WITH CLAMPS USE SPECIAL ACCESSORIES PACKED WITH TONER STARTER KIT MODEL TSK 1 FOR TONER PICK UP CAUTION DO NOT USE DV 5PB PAPER BAG FOR TONER PICK UP HARMFUL TONER COULD BE EXHAUSTED INTO EXPENSIVE EQUIPMENT OR ROOM CAUSING IRREPARABLE DAMAGE oa REMOVE TONER FILTER SYSTE2. air flow for both vacuuming and blowing CAUTION 1 If your DATA VAC has suction but does not clean when hose is attached remove hose from suction end and place onto blower end Blow out the hose sometimes it might be clogged Empty cloth after each cleaning Foam filter should be replaced three times a year FORM 146 MDV III SERVICE Normal maintenance such as motor brush replacement can be made at your local service shop Motor brush life is approximately 500 hours Brushes should be checked between 200 to 250 hour intervals Filter life is 6 months unless used continually in extremely dirty conditions BUCKLE amp STRAP ASSEMBLY 1 Loop strap through buckle as shown 2 Extend length of strap through buckle approx 12 inches 3 Again loop the end of the strap back through the buckle slots as shown to complete the assembly 4 Repeat these steps at opposite end 5 Adjust strap to desired length ONE YEAR LIMITED PARTS WARRANTY TWO YEAR LIMITED MOTOR WARRANTY FOOT OT Guarantee This appliance is guaranteed to be free from defects in workmanship and material for one year from date of purchase See Registry Card The motor is guaranteed for two years The Company agrees to repair or replace any parts under this guarantee which may become defective under normal and proper use and provided the apparatus is used on the voltage circuits marked on the name plate The Company will repair or replace
3. INSTRUCTIONS FOR THE USE AND CARE OF YOUR METRO DATA VAC 2 AND METRO DATA VAC 3 ATTENTION DATA VAC 2 MODEL MDV 2 AND DATA VAC 3 MODEL MDV 3 HAS TONER PICK UP CAPABILITIES WHEN USED WITH TONER FILTERS AND TONER BAGS CAUTION DO NOT USE DATA VAC 2 OR DATA VAC 3 FOR TONER PICK UP WITHOUT SPECIAL FILTRATION PARTS 1 Start appliance by pushing the toggle switch either left or right The two speed switch controls the power level of the DATA VAC 3 The off position is in the middle 2 HOSE When use of hose is desired connect to suction end of the DATA VAC for cleaning purposes to exhaust end for blowing purposes 3 EXTENSION WANDS Reach those inaccessible spots Eliminate bending to clean low areas and under furniture stretching to reach high areas 4 PIK ALL NOZZLE Cleans desks chairs filters upholstery furniture Can also be used as air defuser by placing on exhaust end 5 CREVICE TOOL Cleans those hard to reach tight spots Can be used for vacuuming and blowing purposes 6 POWERIZER AIR MAXIMIZER This tapered accessory concentrates and maximizes air flow for both vacuuming and blowing purposes 7 DUST BRUSH The perfect tool to clean keyboards terminals printers cables and other peripherals AIR PINPOINTER AIR PINPOINTER Narrows air flow down to mere millimeters for blowing into sensitive hard to reach areas between keys printer disc drive etc Exclusive CFM power control on hose reduces
4. M OPEN CLAMPS REMOVE FRONT DOME FROM METRO DATA VAC 2 MODEL MDV 2 METRO DATA VAC 3 MODEL MDV 3 PLACE PRESSURE SENSITIVE TONER SEAL FOUND ON CARDBOARD RING OVER RUBBER DIAPHRAGM OF TONER FILTER BAG REMOVE TONER FILTER BAG AND DISCARD REMOVE CLOTH BAG REMOVE MICRO FILTER GREEN AND DISCARD REPLACE WITH NEW GREEN OR FOAM FILTER REPLACE WITH TONER FILTER BAG FOR TONER PICK UP OR DV 5PB PAPER DISPOSABLE BAG FOR STANDARD CLEANING CHECK BAG FREQUENTLY DISCARD WHEN NO MORE THAN HALF FULL TSK TBF 1105
5. defective parts under this guarantee if returned to the factory authorized service station freight or postage prepaid Please include 7 50 to cover retum mailing insurance and handling Correction of such defects by repair or replacement shall constitute a fulfillment of all its obligations with respect to the apparatus sold hereunder g IMPORTANT Do not tamper with or attempt to take this appliance apart Such action will void this guarantee METROPOLITAN VACUUM CLEANER CO Inc SUFFERN NEW YORK 10901 DATA VAC Computer Maintenance Guide NOW SOLVE COMPUTER OFFICE EQUIPMENT DUST PROBLEMS BEFORE THEY OCCUR HOW WITH METRO DATA VAC COMPUTER HOME OFFICE EQUIPMENT MAINTENANCE SYSTEMS DATA VAC GETS INTO EVERY NOOK AND CRANNY OF COMPUTERS PRINTERS ELECTRONIC OFFICE EQUIPMENT TO VACUUM OR BLOW AWAY ANY ALL DUST PAPER DEBRIS ETC AND WITH DATA VAC 2 AND DATA VAC 3 s TONER FILTER SYSTEM YOU CAN PICK UP TONER SPILLS FROM LASER PRINTERS AND COPIERS LASER PRINTER AND COPIER MANUFACTURERS PRESCRIBE REGULAR MAINTENANCE FOR CLEANER CLEARER DOCUMENTS 1 LASER PRINTERS SHOULD BE VACUUMED AT LEAST ONCE MONTH 2 TONER TENDS TO MIGRATE AND GRAVITATE INTO ACCESSIBLE AREAS CAUSING DEFICIENCIES IN PRINTING PROPER MAINTENANCE INSURES AND INCREASES LASER PRINTER LIFE SPAN 3 RECHARGED LASER TONER CARTRIDGES HAVE TENDENCY TO LEAK MORE 4 INSTALLATION AND REMOVAL OF TONER CARTRIDGE CAN RESULT IN TONER LEAKAGE
Download Pdf Manuals
Related Search