Zinsser 262765 Use and Care Manual
Contents
1. ead Form CS2291 Rev 031813 TECHNICAL DATA COVER STAIN HIGH HIDE ALKYD STAIN BLOCKER PRODUCT APPLICATION cont LIMITATIONS Cover Stain High Hide Alkyd Primer is not intended for application to floors decks roof surfaces or any surface subject to immersion or prolonged contact with water Do not box or intermix Cover Stain High Hide Alkyd Primer with other oil base or water base products MIXING Mix thoroughly to ensure any settled pigment is re dispersed DO NOT THIN APPLICATION Apply only when air material and surface temperatures are between 40 90 F 4 32 C and the surface temperature is at least 5 F 3 C above the dew point The relative humidity should not be greater than 85 Shake or mix thoroughly before using In most cases only one coat is necessary to prime most surfaces If excessive absorption occurs over very porous substrates a second coat may be necessary Spot priming is recommended only under high hiding topcoat paints For best results prime entire surface before painting Apply with a brush roller pad or sprayer Follow manufacturer s instructions when using spray equipment Airless spraying use a 017 tip at 2000 to 2500 P S I CLEAN UP Clean up spills and paint drips with warm water and liquid detergent Wipe up splatters before they dry Follow manufacturer s directions to clean spray equipment Dispose of unused or unwanted product in accordance with loca2. interfere with adhesion If unsure of cleanliness always wash surface with an appropriate ammoniated cleaning solution or solvent do not use TSP as a cleaner Remove any peeling and or unsound coatings Sand any remaining paint film edges smooth Lightly sand exposed exterior wood with 80 to 100 grit sandpaper to remove loose or weathered wood fibers and mill glaze When priming over stained areas first attempt to remove as much of the stain as possible by washing sanding scraping etc Remove exterior mold amp mildew with Zinsser Jomax Mildew Killer and House Cleaner Remove interior mildew with an interior mildew cleaner Allow surface to dry completely before priming Countersink exposed nail heads spot prime and fill all nail holes and gouges with Zinsser Ready Patch spackling compound Wire brush rusty areas Spot prime knots and sap streaks with B I N Primer Sealer before whole surface priming with Cover Stain High Hide Alkyd WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH Approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www epa gov l
3. l we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ge RUST OLEUM BRANDS Rust Oleum Corporation Form CS2291 11 Hawthorn Parkway Phone 877 385 8155 Rev 031813 Vernon Hills Illinois 60061 www rustoleum com An RPM Company
4. l laws regulating solvent based coatings Form CS2291 Rev 031813 TECHNICA L DATA COVER STAIN HIGH HIDE ALKYD STAIN BLOCKER PHYSICAL PROPERTIES HIGH HIDE STAIN BLOCKER Resin Type Low VOC Modified Alkyd Base Pigment Type Titanium Dioxide Solvents Glycol Ethers Water Weight Per Gallon 11 2 Ibs Per Liter 1 34 kg Solids By Weight 54 0 By Volume 37 7 Volatile Organic Compounds activated material Max 100 g l 0 83 lbs gal Recommended Dry Film DFT Per Coat 1 5 2 0 mils 37 5 50p Wet Film to Achieve DFT unthinned material 4 0 5 5 mils 100 137 5p Theoretical Coverage at 1 mil DFT 25p 604 sq ft gal 14 8 m7 l Practical Coverage at Recommended DFT assumes 15 material loss 400 sq ft gal 9 8 m l non porous 300 sq ft gal 7 4 m l porous Touch 30 minutes Dry Times at 70 80 F R 21 27 C and 50 ecoat 1 hour Relative Humidity Stain Sealing ae Full Hardness 7 days Shelf Life 5 years Flash Point gt 200 F 93 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our contro
5. pF TECHNICAL DATA CVS 01 ZINSSER QUALITY SINCE 1849 DESCRIPTION AND USES Zinsser Cover Stain is a high hide modified alkyd base stain blocker designed for application to fire smoke and water damaged surfaces both interior and exterior Interior surfaces include ceilings walls doors trim cabinets furniture and related paintable surfaces Exterior surfaces include exterior siding fascia soffits trim doors walls foundations railings and related paintable surfaces damaged by fire smoke and water PERFORMANCE CHARACTERISTICS Fast drying Recoat in less than 1 hour Sticks to all surfaces and sands easily Designed for interior and exterior surfaces High hiding formula blocks stains from fire smoke and water damage Excellent tannin blocker use to seal bare cedar and redwood Easy soap and water clean up PRODUCTS 262764 1 Quart 262765 1 Gallon 262766 5 Gallon APPEARANCE Cover Stain is white but may be tinted toward the topcoat color with up to 2 oz 59 ml universal colorant per gallon Tinting the primer towards the topcoat improves the hiding power of the topcoat PACKAGING 1 quart 1 gallon and 5 gallon pail COVER STAIN HIGH HIDE ALKYD STAIN BLOCKER PRODUCT APPLICATION SURFACE PREPARATION Surfaces should be clean dry sound and free of dust dirt excessive chalky material grime grease oil wax mildew wallpaper adhesive or any contamination that may
Download Pdf Manuals
Related Search