JELD-WEN H84760 Instructions / Assembly
Contents
1. 1 4 Inspect slabs prior to hanging them on the job Repair noticeable marks or defects that may have occurred from improper storage and handling Field touch up is the responsibility of the installer and includes filling of exposed nail or screw holes refinishing of raw surfaces resulting from job fitting repair of job inflicted scratches and mars and final cleaning of finished surfaces When cleaning door surfaces use a non abrasive commercial cleaner designed for cleaning wood door or paneling surfaces that does not leave a film residue that would build up or affect the surface gloss of the door finish Before finishing hang the door Then remove to finish properly INSTALLATION 1 The utility or structural strength of the doors must not be impaired in fitting to the opening in applying hardware preparing for lights louvers plants on or other detailing Use a minimum of two hinges for JELD WEN 1 3 8 doors up to 80 in height three hinges for all 1 3 4 doors and all doors up to 84 in height and four hinges for doors over 84 up to 96 in height Clearances between door edges and door frame should be a minimum of 1 16 on the hinge edge For latch edge and top rail the clearance should be 1 8 0 1 16 All hardware locations preparations for hardware and methods of hardware attachments must be appropriate for the specific door construction Templates for specific hardware prepara2. Repair refinish or replace product as necessary and adjust all hardware to ensure that it continues to function as it was originally intended RELIABILITY for real life pa a
3. 010 JELD WEN inc JELD WEN the JW icon and Reliability for real life are trademarks or registered trademarks of JELD WEN inc Oregon USA 10 10 RELIABILITY for real life JW l JELD WEN INSTALLATION amp FINISHING INSTRUCTIONS WINDOWS amp DOORS for Interior amp Exterior Wood Door Slabs FINISHING CONTINUED 6 Choose a top coat that is appropriate for the application i e exterior grade products for exterior applications Stain and Clear Finishing 1 To color and seal make first coat a stain and sealer with alkyd resin base Lacquer based toner and lacquer based finishes are only allowed for interior applications not for exterior applications 2 Top coat may be an oil base alkyd resin base polyurethane resin base or latex resin base clear finish A marine grade varnish is recommended on all wood exterior doors For best results apply at least two topcoats Paint Finish If the door is not primed use a good quality oil based primer Paint with at least two topcoats of good quality oil based or water based acrylic latex paint ADJUSTMENT amp MAINTENANCE 1 Ensure that all doors swing freely and do not bind in their frame Adjust the finish hardware for proper alignment smooth operation and proper latching without unnecessary force or excessive clearance 2 Periodically inspect all doors and hardware at least once a year more often in harsh climates for wear damage and natural deterioration
4. JELD WEN WINDOWS amp DOORS INSTALLATION amp FINISHING INSTRUCTIONS for Interior amp Exterior Wood Door Slabs STORAGE amp HANDLING Improper storage handling finishing and installation of wood doors may result in severe damage to the doors Follow these guidelines to help maintain the high quality of the product 1 Allow doors to acclimate for at least 24 hours to local conditions before installation or finishing Store doors flat on a level surface in a dry well ventilated building Doors should be kept at least 3 1 2 off the floor and should have protective coverings under the bottom door and over the top Covering should protect doors from dirt water and abuse but allow for air circulation under and around the stack Avoid exposure to direct sunlight Do not subject interior doors to extremes of heat and or humidity Prolonged exposure may cause damage Buildings where humidity and temperature are controlled provide the best storage facilities recommended conditions 30 50 RH and 30 F to 90 F Do not install doors in buildings that have wet plaster or cement unless they have been properly finished Do not store doors in buildings with excessive moisture content HVAC systems should be operating and balanced Doors should always be handled with clean hands or while wearing clean gloves Doors should be lifted and carried when being moved not dragged across one another PREPARE DOOR
5. ghtly onto glass to prevent water leakage and protect glazing putty Prepare to Finish 1 2 Door must be dry before finishing Remove all handling marks raised grain scuffs burnishes and other undesirable blemishes by block sanding all surfaces in a horizontal position with 120 150 or 180 grit sandpaper To avoid cross grain scratches sand with the grain After sanding clean entire door with a cloth removing all dust and foreign debris Avoid caustic or abrasive materials We recommend applying a pre stain conditioner prior to staining to promote a uniform appearance and avoid sharp color contrasts or a blotchy appearance Oil based sealers or primer coats provide the best base coat for finishing If a water based primer is used it should be an exterior grade product Note Water based coating on unfinished wood may cause veneer splits highlight joints and raised wood grain and therefore should be avoided If a water based primer is desired please contact the finish supplier regarding the correct application and use of these products The information contained herein is provided solely for informational and or educational purposes JELD WEN disclaims any and all liability associated with the use and or provision of this information Any reliance upon the information or advice is at the risk of the party so relying The information contained herein may be changed from time to time without notification 2
6. tion are available from hardware manufacturers Pilot holes must be drilled for all screws that act as hardware attachments Screws that are threaded to the head are preferable for fastening hardware to nonrated doors and are required on fire rated doors FINISHING All six sides of the slab as well as cutouts for hardware must be finished to ensure uniform moisture exposure and dimensional control Failure to finish as directed may result in denial of warranty claims Basic Finishing Recommendations e Use only one manufacture s products and follow all manufacturer s instructions e Stile and Rail panels can float Carefully realign with a wood block and hammer as necessary e Certain species of wood contain chemicals that react unfavorably to some finishes or to foreign materials in the finishing system Where possible test your finish prior to application and eliminate the use of steel wool on bare wood rusty containers or any other contaminate e Most finishes perform better if protected from sunlight and weathering If door is exposed to direct sunlight avoid dark colored finishes This will reduce the chance of warping veneer checking or sunburn e Multiple light coats are better than one heavy coat Be sure the door surface being finished is satisfactory in both smoothness and color after each coat Allow adequate drying time between coats e Doors with clear glass require special care Finish should flow from wood sli
Download Pdf Manuals
Related Search