Yard-Man 1000-6 User's Manual
Contents
1. MODEL 1000 6 16 INCH how 0611 674 10 70 PRINTED IN U S A ALL UNNUMBERED PARTS INTER CHANGEABLE WITH OPPOSITE SIDE SERVICE 2 Most lawn mower service shops are equipped with Tan da S i Yard Man factory built service equipment to give arpening is required when the mower will not cut Ba satisfactorily without the reel blades wiping on the your YARD MAN the same precision it had when it cutter bar came from the factory Prism REF NO V ONAOARODND N NNN e ul i u DD ODO NAT ER ON DO 24 25 26 27 28 29 30 31 32 33 34 MODEL 1000 6 HAND LAWNMOWER WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOLLOWING INFORMATION 3 THE MODEL NUMBER 4 THE NAME OF ITEM 1 THE PART NUMBER 2 THE PART NAME Your Mower is right hand R H or left hand L H as you push Do not use Reference Numbers when ordering Repair Parts always wse Part Numbers PART NO 10 2624 18 3603 55 2643 18 3622 54 41 1523 3 1689 3 169 1509 13 70 2117 15 01 67 1664 6 40 165 1616 114 2616 215 1112 23 55 41 028 1605 533 1530 6 1629 28 104 106 3 1657 19 1509 38 1540 55 1129 233 55 2135 16 55 1530 20 1629 41 1624 138 1631 26 1652 52 PARTS LIST REF PART NAME NO Trunnion u 2er en 35 Spacer let tm a ea ie at 36 Handle Brace _____ 37 Knob Wheel2. Adjust 38 Cover Plate iii 39 Screw 10 x Ph Hd Sht Mtl 40 Grass Catcher Clip 41 Bolt 5 16 18 x 2 Sq Hd 42 Bolt 5 16 18 x 2 Hx Hd 43 Nut 5 16 18 Hex ____ 44 Handle Shaft _____ _ 45 Nut 14 20 Hex ___ __ 46 Cross Handle _____ 47 Bolt 14 20 x 1 Carriage 48 Label Wheel Adjust ooo 49 Label a cdt 50 Spacer Tube Ass y ___ 51 Nut 5 16 24 Hex Lock __ 52 Name Plate ____ _ ___ 53 Rivet 3 16 x Rd Hd __ 54 Retainer _____ aaia 55 Felt Washer iii 56 Felt Retainer _________ 57 Bearing gt eee ii 58 Bushing _____ 59 Screw 10 32 x Hex Hd 60 Washer occ 61 End Plate with Trunnions L H ___ 62 Reel ASS Y z 63 Rivet 3 16 x 13 32 Rd Hd 64 Retainer io 65 Spacer une ety 66 Asler 2268255 hat ee Fan ne ed 67 Be ring me tn en 68 For Illustration See Page 2 PART NO 2619 25 1110 27 41 142 2674 33 1650 21 141 428 109 323 2118 11 55 52 11 451 453 455 2134 15 55 1643 23 1609 171 55 1609 170 55 1529 24 757 2658 23 1129 232 55 1657 23 2118 10 55 425 1622 50 1108 80 41 2616 145 1540 43 1534 8 1509 86 1155 14 1632 143 PART NAME Tre za 22 22 A Drive Wheel Less Tire ___ Cotter Pin Va x ooo Hub Cap a nern Retaining Ring Washer x 11 Pinion Gear L H _ __ Felt Wa
3. sher ____ Pawl Gear Housing Ass y L H Nut 36 24 Semi Fin Hex _ Trunnion Screw Cutter Bar Adjust Screw Rear Screw Pivot R H Thd Cutter Bar co Roller Adj Knob Roller Bracket L H Roller Brackei R H __ Roller Adjust Bolt ici Washer 5 16 x ocio Roller End Plate with Trunnions R H __ Nylon Bushing Gear Housing Ass y R H Pinion Gear R H ii Dust Cover __ ______ a Drive Wheel Ass y with Tire Label Handle Cover Washer 2 22 er te Nut 10 32 Gripco ______ Screw Cutter Bar L H Thd _____ Spring amp Trunnion Ass y ____ Shaft Roller _______ _ _ Standard Hardware ltem Purchase Locally SETTING UP 1 Attach handle brace 1 Fig 1 2 Attach handle brace spacer and handle as shown tighten nuts 2 securely 3 Attach cover plate and grass catcher clip with screws 3 4 If grass catcher is used attach catcher hooks on inside of frame under HEAD of roller bracket bolt as shown in Fig 1 CUTTING HEIGHT ADJUSTMENT Locate wheel levers and roller knobs in positions shown on chart attached to back of han dle cover plate for cutting height desired To make these adjustments with maximum ease proceed as follows PLACE WHEEL LEVER AND ROLLER KNOB IN POSITION SHOWN FOR HEIGHT OF TO ADJUST WHEELS 1 Tilt mower back on roller to raise wheels
4. slightly off the ground 2 Press levers toward outside of mower to unlock them from present position and move to new position Be sure both levers are in same position and trunnions are firmly seated in holes in chassis end plates TO ADJUST ROLLER 1 Tilt mower forward to raise roller slightly off the ground 2 Loosen roller knobs 2 full turns and move to new position Be sure both knobs are in same position and firmly seated in notch in chassis end plate then tighten securely par ono 3 178 874 lole fen ever A D 6 B B A A TO TIGHTEN CUTTER BAR 1 Fig 3 Loosen top nut 5 one quarter turn 2 Tighten lower nut 6 3 Bolts 7 and 8 must be tight after adjustment IMPORTANT REEL BLADES SHOULD NOT CONTACT CUTTER BAR SILENT YARD MAN PAPER TEST 1 Insert strip of newspaper approx 2 wide be tween cutter bar and reel Fig 4 2 Turn reel slowly backward with wheels off ground 3 Adjust cutter bar so that reel blades pinch the paper without cutting it 4 Check cutter bar clearance in this manner at several points moving toward right hand side of mow LUBRICATION 1 Seals on all bearings hold dirt out and grease in No further lubrication is required until mower is sharpened 2 Oil Roller Bearing once or twice a year
Download Pdf Manuals
Related Search