Yamaha NX-E200 Owner's Manual
Contents
1. YAMAHA o SpeakerSysem_ _ Nn PERRE 2 00000000 OWNER S MANUAL MODE D EMPLOI EF i BAB Thank you for selecting this Yamaha 200 speaker system PRECAUTIONS Read this before using the speakers To assure the finest performance please read this manual carefully Keep it in a safe place for future reference Install the speakers in a cool dry clean place away from windows heat sources sources of excessive vibration dust moisture and cold Avoid sources of humming transformers motors To prevent fire or electrical shock do not expose the speakers to rain or water To prevent the enclosure from warping or discoloring do not place the speakers where they will be exposed to direct sunlight or excessive humidity Do not place the following objects on the speakers Glass chine etc If glass etc falls by vibrations and breaks it may cause personal injury A burning candle etc If the candle falls by vibrations it may cause fire and personal injury A vessel with water in it If the vessel falls by vibrations and water spills it may cause damage to the speakers and or you may get an electrical shock Do not place the speakers where foreign objects such as water drips might fall It might cause a fire damage to the speakers and or personal injury Do not place the speakers where they are liable to be knocked over or struck by f2. but there is still a chance that placing them too close to a TV set might impair picture color Should this happen move the speakers away from the TV set REMOVING THE FRONT COVER The front cover is fastened to the enclosure at four point and can be removed if desired To remove the cover hold on to both sides and slowly pull straight away from the speaker To reattach line up the four pegs on the inner surface of the cover with the four corresponding holes on the speaker and push gently Note When the cover is removed be sure not to touch the speaker units with your hands or to exert excessive force with tools SPEGIFICATIONS 2 way bass reflex speaker system Magnetic shielding type Driver 13 cm 5 cone woofer 2 5 cm 1 dome tweeter Nominal Input Power 60 W Maximum Input Power 110 W gaan 60 Frequency Response 55 Hz 28 kHz 87 dB 2 83 V m Crossover Frequency 3 kHz Dimensions W x 186 300 222 7 5 16 11 13 16 8 3 4 4 kg 8 Ibs 13 oz x 2 A CCESSOTIES Speaker cable 4 m x 2 Please note that all specifications are subject to change without notice Care should be taken not to exceed the input power values noted above YAMAHA YAMAHA CORPORATION Printed in China
3. UIP voo V685700
4. alling objects Stable placement will also ensure better sound performance Placing the speakers on the same shelf or rack as the turntable can result in feedback Any time you note distortion reduce the volume control on your receiver to a lower setting Never allow your receiver to be driven into clipping Otherwise the speakers may be damaged When using a receiver with a rated output power higher than the nominal input power of the speakers care should be taken never to exceed the speakers maximum input Do not attempt to clean the speakers with chemical solvents as this might damage the finish Use a clean dry cloth Do not attempt to modify or fix the speakers Contact qualified YAMAHA service personnel when any service is needed The cabinet should never be opened for any reasons Secure placement or installation is the owner s responsibility YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers CONNECTION TO YOUR RX E200 RECEIVER BEFORE MAKING CONNECTIONS MAKE SURE THAT THE RX E200 RECEIVER IS SWITCHED OFF When this unit is connected to the RX E200 receiver refer also to the owner s manual supplied with the receiver CONNECTIONS Speaker R Connect the screw type input terminals at the rear of the speakers to the speaker output terminals of the receiver with the provided speaker cables One side of the speaker cable is red and the other side is bla
5. ck Connect the terminals on the receiver and speakers using the red side Connect the terminals on both components using the black side of the cable Connect one speaker to the left marked L terminals of the receiver and the other to the right marked R terminals Make sure not to reverse polarity If a speaker is connected with reverse polarity the sound will be unnatural and lack bass Speaker L Bo Speaker output terminals of the receiver J Red line Black line How to connect Loosen the knob 2 Insert the bare wire Remove the insulation coating at the extremity of each speaker cable by twisting the coating off Good No Good 3 Tighten the knob and secure the cable Test the firmness of the connection by pulling lightly on the cable at the terminal Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier or both of them PLACING THE SPEAKERS e Place the speakers on a sturdy vibration free surface You may not be able to obtain good bass quality when the speakers are placed directly on the floor Put a block etc under the speakers Better stereo images will be obtained when the speakers are slightly angled in towards the listening position Note These speakers feature a magnetically shielded design
Download Pdf Manuals
Related Search