XM Satellite Radio P/N 08A15-1E1-000 User's Manual
Contents
1. SOURCE POWER Initial Setup Scrolling feature This feature allows the broadcast text information such as artist song tittle and station information to move continuously across the screen This is the default setting however this feature can be disabled if the user prefers no scrolling Below shows how to disable or enable this feature Press and hold the SETUP button for 2 seconds or more Turn the rotary encoder or press the or button to select the SCR Press the or button to set this feature ON or OFF Pumpe Press setup button to return to normal operation mode SOURCE POWER Receiving XM channels with the XM receiver 1 Turn the vehicle s radio on to FM and tune to the XM radio s modulator fre quency between 88 7 to 89 9 Refer to page 7 for how to set XM radio s modulator frequency 2 Pressthe POWER button of the display module to turn the XM radio on 3 Turnthe rotary knob to display the desired channel Pressing and holding down the or button on the display will change channels continuously a Rotary Knob SOURCE POWER 4 Up w Down Storing XM channel presets 1 After tuning in the desired channel press and hold the rotary knob for 2 seconds or more until the channel name on the display blinks 2 Turn the rotary knob to select the preset numb2. e XM radio is being updated with the latest encryption code Wait until encryption code is fully updated Channel 0 and 1 should function normally e XM signal is too weak at the current location Wait until the car reaches a location with stronger signal Display Information Display messages for XM radio operation radio is acquiring audio or program information Wait until the radio has received the information e The channel currently selected has stopped broadcasting Select another channel e The user selected a channel number that does not exist or is not subscribed to The unit will revert back to the previously selected channel e No artist or tittle information associated with the channel at this time action required 16 RF MODULATOR UNIT RF Output Frequency selectable RF Output Voltage RF Modulator input Sensitivity Impedance Recommended Operating voltage Recommended Temperature range DISPLAY MODULE Width Height Depth Weight FM MODULATOR Width Height Depth Weight SPECIFICATIONS 87 7 89 9 MHz 70 dBuV 500mV 10 k Ohms 13 4 Vdc 14 F 140F 10 C 60 113 mm 4 7 16 39 5mm 1 9 16 19 mm 25 32 0 20 kg 7 oz 130 mm 5 1 8 35 mm 1 3 8 74 mm 2 15 16 0 38 kg 13 4 oz REF NO MROHL210 HONDA 08A15 1E1 000 81 2003 American Honda Motor Co Inc All Rights Reserved Printed in U S A
3. may be ground based coverage in some of these areas that will provide uninterrupted service of satellite radio The XM radio will not operate only when there is no signal from both satellite and ground based antennas In tunnels and indoor Locations surrounded Locations surrounded parking lots by tall buildings by tall trees Sound in your car The signal is broadcast in a digital format so that if you do run into a situation where both the satellite antenna and the ground based antenna lose the signal the sound will drop off completely This condition would result in no static and may sound as though the unit were shut off As soon as the obstruction is cleared or a ground based signal is re established the sound will come back on If you do experience a loss of signal check the display module to make sure it is powered on and check the display for NO SIGNAL Refer to page 15 of this manual for a display of messages SOURCE POWER Initial Setup Turning power on and off 1 Press the SOURCE POWER button to turn the unit on NOTE The unit can be turned on by pressing any of the buttons of the display module 2 Press and hold the SOURCE POWER button for 2 seconds or more to turn the unit off NOTE When turning the unit on and off with the POWER button Be sure to lower the volume level of the vehicle s radio when turning the unit on and off with the POWER butto
4. OPERATING INSTRUCTIONS XM RADIO ac RADIO FE 7 P N 08A15 1E1 000 HONDA General information Initial Setup Operation Troubleshooting Information Specifications Please write the serial number and the XM ID number from the bottom of the tuner in the space below for your records Serial No XM ID No How the service works The XM service is based on two satellites that have fixed positions over the equator One satellite for the east coast of the United States and the other for the west coast The two satellites continuously broadcast radio signals throughout the continental United States The XM service also uses ground based antennas that broadcast into areas that may be obstructed from satellite radio signal Not all areas that are obstructed have ground based antennas as a backup signal XM radio makes every effort to minimize the areas that do not receive radio signal Visit XM Satellite radio at www xmradio com or call 1 887 XMRADIO for more information Note Service activation and antenna is necessary to receive XM Satellite radio transmission Locations where satellite signals are received easily Satellite signals are received best in the areas where there are no tall buildings trees or tall objects that can obstruct the signals Satellite radio signals may not be received in areas listed below There
5. er you want to store 3 Press the rotary knob within 5 seconds once when the correct preset number is dis played 4 Repeat the procedure to store up to five additional channels Note If you store a channel in a preset memory which already has a station the current channel will be cleared and replaced with the new one Receiving stored XM channels 1 Press the or 4 button to access the desired satellite channel in the memory SOURCE POWER E TS A Up ww Down Category search Category search functionally allows you to search for a specific channel by the category of pro gramming it offers or to surf within a category 1 Momentarily press the rotary knob to display the category of the channel that is cur rently selected 2 While the category is displayed turn the rotary knob to select a different category Note You can also press the or button to select a category 3 Within 5 seconds of selecting the category press the rotary knob to select the next channel within that category Repeatedly press the rotary knob within 5 seconds to select additional channels with in that category SOURCE POWER ST Rotary Knob 4 Up w Down Changing the display Text information such as the channel name artist name feature and song program tittle is available with each XM channel This unit can disp
6. lay this text information as explained below 1 Press the DISP SETUP button Each time you press the button the display changes as shown below Channel name Artist name Song tittle display display display Troubleshooting Guide If you encounter a problem please review the items listed below This guide will help you to isolate the problem Make sure the rest of your system is operating properly If necessary consult your local authorized Honda dealer SYMPTOM CAUSE SOLUTION XM radio will not operate Ignition switch is in the off position Turn Ignition to the on position Power to XM radio is Turn the XM radio on not turned on Possible blown fuse Contact your Honda dealer The XM radio appears to be on Vehicle s radio volume is set too low Raise radio volume level but there is no sound from the Vehicle s radio not tuned to correct Check radio make sure the speakers frequency vehicle s radio is set correctly The antenna may not be connected Contact your Honda dealer Big difference in sound level XM radio needs Level adjustment Refer to page 8 in manual between car audio system and XM radio Poor or no reception for XM The antenna may not be connected Contact your Honda dealer 14 Display Information Display messages for XM radio operation e The XM antenna is not connected to the XM radio module Check whether the XM antenna cable is attached securely to the XM radio module
7. n This will prevent any electrical popping noises being transmitted from the unit SOURCE POWER Initial Setup Modulator frequency setting 1 2 3 4 5 Press the DISP SETUP button to return to normal mode Press and hold the DISP SETUP for 2 seconds or more Turn the rotary encoder or press or button to select the frequency setting mode displays the frequency of the desired modulation station Press the or button to set the frequency The frequency is varied by 200kHz 0 2MHz steps from 87 7 to 89 9 MHz Note In order to resume normal AM and FM radio reception turn the power of the XM radio display module off Press and hold the SOURCE POWER button for 2 seconds or more Rotary Knob SOURCE POWER 4 Up w Down Initial Setup XM level setting XM output level When your XM receiver is connected to the factory installed radio this feature will allow the user to choose between 4 levels of output XM level 1 to 4 to better match the output level of the Honda Acura radio 1 Press and hold the DISP SETUP button for 2 seconds or more 2 Turn the rotary encoder or press the or button to select the XM LEV 3 Press the or button to set the desired volume level XM LEV 1 XM LEV 4 Level 3 or 4 is recommended 4 Press DISP SETUP button to return to normal operation mode
Download Pdf Manuals
Related Search