Xerox DocuTech 180 HighLight Color Installation Guide
Contents
1. 000 ft 1830 m 701P46151 October 2006 6R90361 XE Developer Black Red NA Blue Green Royal Blue Cardinal Red Cyan Magenta Yellow Fuser Blend 8R12938 1 bottle 8R12939 6 bottles Fuser Shield 8R4077 1 bottle 8R7618 6 bottles Dry ink waste container NA HLC developer waste bottle 604K24870 4 bottles Binder tape Black 8R7186 Binder tape White 8R7187 Binder tape Gray 8R7188 Binder tape Blue 8R7189 Stitcher Wire 8R1174 Will be available in the near future NOTE The formula for the DocuTech HLC fuser lubricant was changed in 2006 to provide better image quality and to prevent image transfer The new fuser formula is called Fuser Shield The Fuser Blend and the Fuser Shield CANNOT be intermixed in a DocuTech HLC To change from one fuser lubricant to another requires a service call and cleaning or replacing components The two fuser formulas are identified with different color bottles and caps If a machine is running with in line finishing equipment the new Fuser Shield may contribute to poor binding at the binder glue seam Customers experiencing this problem can have their equipment returned to using Fuser Blend by placing a service call to clean and or replace components Do NOT place Fuser Blend in a machine that has been using Fuser Shield Monthly duty cycle is up to 6 million DT 180 HLC e The Xerox Supplies Marketing Center 1 800 822 2200 is a2. for the 20 Amp electrical service is identified below Controller 36 Track Tape Optional Line Options Dedicated Dedicated Voltage 115vac 115vac Amperage 20 20 Cycles 60 Hz 60 Hz Xerox Receptacle Part No 60083703 60083703 Receptacle NEMA Part No 5 20R 5 20R Power Cord Xerox Part No 98K19950 98K19950 Receptacle Diagram 97502370 97502370 Installation Considerations Dedicated electrical service is required for each component 2 The controller can be connected to a 15 amp or 20 amp outlet 3 The length of the cable from the controller to the printer is 16 feet 4 8 metres 4 Do not use an adapter to connect the controller to an electrical outlet that lacks a ground connection terminal 5 The customer is responsible for providing the network and the client workstation s The Ethernet interface on the DocuSP controller is a auto sensing 10 100 1000 MB sec twisted pair standard BaseT 6 The Ethernet connection to the DocuSP controller must be compatible with the Institute of Electrical and Electronics Engineers IEEE 802 3 standard XEROX Installation Preparation Document for physical installation of the product only Xerox DocuTech 180 HighLight Color Paper Handling e 16 to 110 Ib 60 to 200 gsm cut sheet paper weights e 8 by 10 in to 14 33 x 17 in 203 by 254 mm to 364 by 432 mm including A4 A3 and B4 paper sizes destination dependent e 7 by 10 in 17
3. 8 by 254 mm optional enablement kit e Transparencies label stock tab stock carbonless paper pre perforated stock Paper stock weights less than 16 Ib are not recommended e Textured stocks are not recommended e Some 65 Ib stocks may not fully fuse Input Main tray tray 1 Auxiliary tray tray 2 Capacity 1 100 sheets 20 Ib 75 gsm 600 sheets 20 Ib 75 gsm 2 600 sheets each 20 Ib Operating Supplies Reorder No Dry Ink Black 6R206 US CA Dry Ink Blue 6R1191 US CA 6R90343 XE Dry Ink Red 6R1192 US CA 6R90344 EU Dry Ink Green 6R1193 US CA 6R90345 EU Dry Ink Royal Blue 6R1255 US CA 6R90356 XE Dry Ink Cardinal Red 6R1277 US CA 6R90358 XE Dry Ink Cyan 6R1284 US CA 6R90359 XE Dry Ink Magenta 6R1296 US CA 6R90360 XE Dry Ink Yellow 6R1299 US CA High capacity trays trays 3 and 5 75 gsm Fuser bypass tray tray 4 550 sheets each 20 Ib 75 gsm Output Tray Capacity Stacker 3000 sheets 20 Ib 75 gsm Stitcher 2 70 sheets 20 Ib 75 gsm 35 000 stitches per spool Binder 15 125 sheets 20 Ib 75 gsm 425 11 in binds per spool Top tray 500 sheets 20 Ib 75 gsm Environmental Requirements Temperature 50 to 85 F 10 to 29 C Humidity 30 to 65 RH Non condensation Heat Emission printer 4454 BTU Hr Standby 32 770 BTU Hr Operating Altitude above sea level Up to 6
4. Installation Preparation Document for physical installation of the product only Xerox DocuTech 180 HighLight Color The main DocuTech 180 HLC components are e Digital Front End Controller CD DVD combo drive color flat panel monitor keyboard and mouse Ethernet interface 10 100 1000 BaseT Two printer interface cards Controller Stand Options e USB floppy disk drive e Solaris 10 and DocuSP print services software Printer e Black plus one highlight color e Xerographic engine with laser raster imaging system for black and Light Emitting Diode for color Permanent housing for black dry ink customer changeable unit CCU for color dry ink Prints simplex or duplex e Two tray interposer In line finishing module which includes a binder stitcher and stacker e Optional Bypass Transport to provide connection to additional finishers Additional dry inks not listed on this document will be customer options as they become available and will be offered under standard Xerox terms and conditions Space Requirements Service Space Envelope The dimensions shown below are absolute minimums Configuration Min total Weight req d Width x depth With two tray 3724 Interposer and Ibs Binder Stitcher 1689 kgs Controller stand 36 in 36 in 91 cm 91 cm e The minimum total space required includes the required space necessary for the Xerox service personnel to service the printer A minimum of 78
5. L6 ASCII PDF TIFF VIPP PPML Additional data streams will be available post launch Printing Considerations Not all features and capabilities are available with every print driver and OS Protocol combination Custom software applications may produce unexpected results Other Considerations The Xerox Welcome Center at 1 800 821 2797 is available to provide customer support 701P46151 October 2006 XEROX
6. inches 198 cm clearance from the floor to the nearest overhead obstruction must be maintained e No obstructions such as power poles are allowed such that they interfere with the Xerox Service Representative s ability to access the rear of the printer for service e The printing system must be installed in a fixed location Space requirements for the controller stand are 36 x 36 inches 91 x 91 cm For proper operation the printer must be perfectly level On floors less than two degrees out of level a leveling kit must be used to level the equipment The printer will not function properly on floors more than two degrees out of level e For detailed space requirements and diagrams refer to the DocuTech 128 155 180 HighLight Color Installation Planning Guide 701P46151 October 2006 Electrical Requirements printer The printer requires for 60 HZ service 2 cords required MultiSource 2 phase dual power cord configuration Voltage 208 240 4 wire 208 240 4 wire Amperage dedicated 50 30 Cycles 60 Hz 60 Hz Receptacle Xerox Part No Receptacle NEMA Part No 14 50R 14 30R Receptacle Diagram E 54 Power Cord Kit Number Power Cord Length 15 feet 15 feet For 50 Hz service 30 amp dedicated service WYE 220 380 VAC or 230 400 VAC or 240 415 VAC 3 phase Agency certifications UL cUL CE Mark FCC Electrical Requirements Controller The Controller requires 20 AMP dedicated service The information
7. vailable for ordering Xerox supplies including paper and other throughput material e The supply of developer for each of the color toners is ordered and maintained at the customer site by the Xerox Service Representative and is not orderable by the customer e The Dry ink waste container supply is maintained at the customer site by the Xerox Service Representative and is not orderable by the customer XEROX Installation Preparation Document for physical installation of the product only Xerox DocuTech 180 HighLight Color Network Connectivity The DT 1xx HLC supports the following connectivity Network Operating Protocol Topology System Novell 3 x 4 x IPX SPX Ethernet NDS or Bindery mode Windows NT 4 0 TCP IP LPR Ethernet Token Ring Win2000 WinXP AppleTalk EtherTalk Ethernet LPD Server TCP IP Ethernet Token Ring Unix Systems Online Channel IBM Ethernet Token Ring 3211 4245 Bus and Tag NOTE Token Ring is not available for AppleTalk or Novell environments The system supports Port Printing and HTTP and IPP Printing modes Additionally SNMP Services and DocuSP Remote Workflow can be enabled on the customer s network Print Drivers Environments The DT 1xx HLC supports the following print drivers e Windows 95 98 ME 2000 XP e Windows NT 4 0 e MAC OS 8 6 amp higher e Solaris 2 8 PDL Compatibility The system interprets the following data streams PostScript Level 3 HP PCL5c HP PC
Download Pdf Manuals
Related Search